After my auto electrician arrived to remove the imboliser I thought that would be the end of my electrical problems... I wish.
Went to crank the engine and it will now turn the starter off the key which is nice but it won't fuel or get spark. This is very weird considering that it was fine before a service and the imboliser packed up. So far I've replaced
ICV, AFM, Blue & Brown Pin Sensors, Timing Belt inc Tensioner, PS belt, Fan belt, Inlet Manifold inc Gaskets, Waterpump and Injectors. This was all done over a peroid of about 3 weeks without the car being actually cranked but with the ignition going on and off for various reasons. The sparky tested the fuel pump connection, ecu and connections, relay, fuses and most other things he could think of but it's still not getting spark or fuel. I was wondering if it's a crank sensor or something of the like because he mentioned that it was the only thing he could think of to try.
Anyone shed any light for me, this is starting to really piss me off and god knows how much the sparky is going to charge...
No spark or fuel...
Moderator: martauto
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
Cyruz
- E30 Zone Newbie

- Posts: 219
- Joined: Sat Oct 15, 2005 11:00 pm
- Location: Bournemouth
Also thought I'd add that if you disconnect the starter the fuel pump runs constantly like it's being bridged, does it work of some sort of system where it earths itself and cuts off on initial ignition of the engine just to fill the rail and injectors.

-
Cyruz
- E30 Zone Newbie

- Posts: 219
- Joined: Sat Oct 15, 2005 11:00 pm
- Location: Bournemouth
Where abouts is this, I'm fine at most DIY jobs but this is a little out of my league so I'm learning fast. It's not the connector on the front of the block that reads from a large pully is it? Also whats the connector that runs to the sump on the right hand side (in drivers seat), just low oil warning sensor?Could well be crank sensor...
Thanks

-
Nelly
- Gumbo

- Posts: 4239
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Divorce Central
-
Ant
- Retired Team Member

- Posts: 10496
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: PD+E dept :D
crank sensor is indeed @ the front reading off the trigger wheel, trace the wires back to the plug under the dia socket( m20) and unplug it, using a multimeter measure the resistance accross the two conected pins, you should get 330 ohms
if with the engine cranking the rpms are displayed on the tacho, I doubt the crank sensor is to blame dude
the fuel pump should prime on ign on, then be dormant until the engine is cranked and running.
do you have poer to the ECU itself ? there's an ign on feed and a 12V perm feed, both must be OK for the engine to run.
and just check for any obvious faileure like plug adrift somewhere, auto sparkies are good, but forgetful @ times
HTH
if with the engine cranking the rpms are displayed on the tacho, I doubt the crank sensor is to blame dude
the fuel pump should prime on ign on, then be dormant until the engine is cranked and running.
do you have poer to the ECU itself ? there's an ign on feed and a 12V perm feed, both must be OK for the engine to run.
and just check for any obvious faileure like plug adrift somewhere, auto sparkies are good, but forgetful @ times
HTH
Product Development and Endurance for Delphi.
Original performance chips, original works not unlicensed copies
Email FTW
Original performance chips, original works not unlicensed copies
-
Nelly
- Gumbo

- Posts: 4239
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Divorce Central
-
Nelly
- Gumbo

- Posts: 4239
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Divorce Central
-
Cyruz
- E30 Zone Newbie

- Posts: 219
- Joined: Sat Oct 15, 2005 11:00 pm
- Location: Bournemouth
Will check all this crap in the morning, I hate my new e30, every time I fix something, something else breaks...
I blame god... well god and karma.
I blame god... well god and karma.



