multilpe m20 throttle bodies
Moderator: martauto
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
You say that TBs don't suffer from having low air speed, but that's not strictly speaking true.
You can mask the effects, but that's it.
I've got 48mm runners into 40mm TBs on mine which is simply too big. The over sizing leads to very low air speed in the inlets at idle with the consequence that my car uses almost as much fuel at idle as it does driving along at 30mph as it's needing to have so much fuel added to compensate for fuel dropout! And that's with the injectors in the standard position right next to the head.
The other downside to oversizing is that you'll get to a point where opening the throttle any further doesn't give any more power as the butterfly isn't the biggest cause of restriction anymore so effectively you have some wasted travel left.
You can mask the effects, but that's it.
I've got 48mm runners into 40mm TBs on mine which is simply too big. The over sizing leads to very low air speed in the inlets at idle with the consequence that my car uses almost as much fuel at idle as it does driving along at 30mph as it's needing to have so much fuel added to compensate for fuel dropout! And that's with the injectors in the standard position right next to the head.
The other downside to oversizing is that you'll get to a point where opening the throttle any further doesn't give any more power as the butterfly isn't the biggest cause of restriction anymore so effectively you have some wasted travel left.
-
maxfield
- Old Skooler

- Posts: 15185
- Joined: Sat Nov 26, 2005 11:00 pm
- Location: Mansfield
this is player6s (scotts) car.tee wrote:Whos car is this? tried to search "Dhiblas" and got nothing. Anyone know the name of this fit and if it is still available anywhere?Andy335Touring wrote:link doesn't work, i think they sold the Dhiblas(Sp?) TB's the same as Scotts ?
running 260hp

-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
At the end of the day you're fitting a set of throttle bodies that would be adequate for an E36 M3 - with four valves per cylinder and Vanos to alter valve timing. That's the theory.
Blowing all this apart is an Alfa Romeo twin cam from 1000 years ago. Even the little 1300 (1290) Veloce units were running 40DCOE's, never mind the 1570, 1750 and 1970cc units. They all idled smootgly, were very driveable and weren't bad on fuel. The 2 litre did 130 solid bhp using some pretty mild cams - so I've shot myself in the foot somewhat........
The Hartge H27SP used individual throttle bodies (I think) and the power was supposedly 220 bhp. I have never seen one and wonder if any were actually sold. From the pic I have, it still draws though a throttle body sized inlet and an air flow meter. A bit crap then.
Blowing all this apart is an Alfa Romeo twin cam from 1000 years ago. Even the little 1300 (1290) Veloce units were running 40DCOE's, never mind the 1570, 1750 and 1970cc units. They all idled smootgly, were very driveable and weren't bad on fuel. The 2 litre did 130 solid bhp using some pretty mild cams - so I've shot myself in the foot somewhat........
The Hartge H27SP used individual throttle bodies (I think) and the power was supposedly 220 bhp. I have never seen one and wonder if any were actually sold. From the pic I have, it still draws though a throttle body sized inlet and an air flow meter. A bit crap then.
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
From Hartge literature on the H27SP:
" The 10.2:1 compression six cylinder two valve engine delivers 220 hp at 6400 rpm. This is the technical maximum performance based on the small six cylinder engine. In order to acheive the considerable 81 bhp per litre output, the advanced single throttle system was required, the function being that each cylinder has its own mixture control system with throttle valve and fuel injector. Extensive development was required due to the optimisation of the intake length and cross sectional area combined with the detailed reprofiling of the Motronic system".
0-62 mph in 7 seconds (same as a standard 325i according to some zoners....
) and 146 mph.
" The 10.2:1 compression six cylinder two valve engine delivers 220 hp at 6400 rpm. This is the technical maximum performance based on the small six cylinder engine. In order to acheive the considerable 81 bhp per litre output, the advanced single throttle system was required, the function being that each cylinder has its own mixture control system with throttle valve and fuel injector. Extensive development was required due to the optimisation of the intake length and cross sectional area combined with the detailed reprofiling of the Motronic system".
0-62 mph in 7 seconds (same as a standard 325i according to some zoners....
-
trigger
- E30 Zone Newbie

- Posts: 123
- Joined: Wed Apr 12, 2006 11:00 pm
- Location: harlow
why cant you fit a remote servo that were used one rovers, thats what i used to use and it frees up that space, motoring news paper is a good source for these sort of parts,Turbo-Brown wrote:Don't the magnolesti manifolds point no. 6 cylinder's inlet straight at the servo though?
Why would you need a hairy cam to make it run too?
cant see the point of going to the trouble of fitting unless you couple it up with a worked head and defo a trick cam of some sort, i would have thought the gains otherwise would be quite minor pound for pound and not really worth the expense
-
tee
- E30 Zone Newbie

- Posts: 150
- Joined: Sat Jan 22, 2005 11:00 pm
I have just aquired 6 38mm throttle bodies from a K1200 bike engine, will these be big enough for a 2.7 M20?
Also how do you deal with idle as there is no idle control valve when using these. Do you just use the idle stop on the TB's instead? I will using Megasquirt so I presume this is what you do??
Also how do you deal with idle as there is no idle control valve when using these. Do you just use the idle stop on the TB's instead? I will using Megasquirt so I presume this is what you do??
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
I reckon those will be perfect Tee 
Idle control can be done one of two ways.
Either you put up with a very low idle when the engine's cold and have the throttle cracked open just enough to give a reasonable idle when warm (mine's like this idling at around 400rpm cold and 900warm). The ECU takes care of idle stabilisation by advancing the ignition (by up to 20degrees on mine) when the engine's below your preset target idle.
The other (and better) way is to incorporate a balance chamber into your manifold which can serve two purposes. The first is to give a nice steady vacuum signal to the servo and a MAP sensor if you have need of one, the second is that you can connect an IACV to it so that the ECU can control the idle speed properly.
Idle control can be done one of two ways.
Either you put up with a very low idle when the engine's cold and have the throttle cracked open just enough to give a reasonable idle when warm (mine's like this idling at around 400rpm cold and 900warm). The ECU takes care of idle stabilisation by advancing the ignition (by up to 20degrees on mine) when the engine's below your preset target idle.
The other (and better) way is to incorporate a balance chamber into your manifold which can serve two purposes. The first is to give a nice steady vacuum signal to the servo and a MAP sensor if you have need of one, the second is that you can connect an IACV to it so that the ECU can control the idle speed properly.
-
tee
- E30 Zone Newbie

- Posts: 150
- Joined: Sat Jan 22, 2005 11:00 pm
On the throttle bodies I have there is a electronic control box with a plunger on it that opens the throttles slighty on cold start, just need to find out whether the Megasquirt can control this. Will be looking at the K1200 wiring diagrams to see whether it is pulse width modulated or what.
Also how have you made your plenum chamber? metal, plastic, fibreglass??
Also how have you made your plenum chamber? metal, plastic, fibreglass??
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
I'd guess at the plunger just needing a switch to make it go on or off. Had thought about rigging something up for mine that's operated by a simple switch.
Made my plenum from aluminium sheet about 1.2mm thick, ali plate around 6mm thick and 2" aluminium pipe.

Made my plenum from aluminium sheet about 1.2mm thick, ali plate around 6mm thick and 2" aluminium pipe.

-
Ant
- Retired Team Member

- Posts: 10496
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: PD+E dept :D
MS can do a 3 wire PWM idle valve, or a two wire on/off valve as used on LE jetronic equipped carsOn the throttle bodies I have there is a electronic control box with a plunger on it that opens the throttles slighty on cold start, just need to find out whether the Megasquirt can control this. Will be looking at the K1200 wiring diagrams to see whether it is pulse width modulated or what.
I dont fit an ICV of any sort, MS for warmup enrichment with a look up table for ignition timing based upon coolant and IAT to prop the cold idle speed up, turn key, hold rpm @ 1K for 10 seconds, then idle/drive fine
Product Development and Endurance for Delphi.
Original performance chips, original works not unlicensed copies
Email FTW
Original performance chips, original works not unlicensed copies
-
tee
- E30 Zone Newbie

- Posts: 150
- Joined: Sat Jan 22, 2005 11:00 pm
Turbo-brown - would it be poss to meet up with you at some point to see your car and get a few ideas? I work in Bracknell so not too far away.
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
-
tee
- E30 Zone Newbie

- Posts: 150
- Joined: Sat Jan 22, 2005 11:00 pm
Yeah stu, and I have 2 left over and poss be able to get another 2 aswell
Perfect for a 4 pot
Working where I do comes in handy sometimes.
p.s notice the old e30 avantar
Working where I do comes in handy sometimes.
p.s notice the old e30 avantar
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
Yeah no worries, gimme a shout when you're free!tee wrote:Turbo-brown - would it be poss to meet up with you at some point to see your car and get a few ideas? I work in Bracknell so not too far away.
Guess a weekend would be better as it's a bit lighter for poking and prodding things
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
yes, i hear ya, my good friend!! and you know what my next question is....tee wrote:Yeah stu, and I have 2 left over and poss be able to get another 2 aswellPerfect for a 4 pot
Working where I do comes in handy sometimes.
p.s notice the old e30 avantar
and yes i did notice the avatar! i bet tat brings back memories? stick a few pics of it up mate, everyone will love it
i'll talk to you at the weekend about them t'bodies. i still got some tools of yours anyway...
-
miniblob
- E30 Zone Addict

- Posts: 3153
- Joined: Thu Jan 05, 2006 11:00 pm
- Location: Croydon/Uckfield
What, no spare tb's for my car!?!?!?!?! 
327 Touring with bass!!!
>>> WWW.DNRVINYL.CO.UK >>> UK GARAGE SPECIALIST >>>
>>> WWW.DNRVINYL.COM >>> FREE MIX DOWNLOADS!!! >>>
>>> WWW.DNRVINYL.CO.UK >>> UK GARAGE SPECIALIST >>>
>>> WWW.DNRVINYL.COM >>> FREE MIX DOWNLOADS!!! >>>
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
-
tee
- E30 Zone Newbie

- Posts: 150
- Joined: Sat Jan 22, 2005 11:00 pm
You never know whats laying around up here Rob!miniblob wrote:What, no spare tb's for my car!?!?!?!?!
I'll see whats available
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon


