**Mtec I lump in Mtec II engine bay**

Need technical Q/A then you're in the right place

Moderator: martauto

BIGJO
E30 Zone Camper
E30 Zone Camper
Posts: 1191
Joined: Thu Apr 27, 2006 11:00 pm
Location: N.W London & Brighton

Post Wed Nov 29, 2006 5:45 pm

Hello people, i'm getting myself an earlier 2.5 engine (from Mtec I) for my Mtec II Sport that requires a new lump.


Can I just ask what complications there might be with installing the lump? For example, will it be a straight out & in jobby or will there need to be any customising? Assuming that all the bits are there etc?


Also, considering whether I can put my 288/288 cam in with high performance valve springs but need to get the tolerances checked by a specialist as had a problem with my engine, hence the replacement.


Would anyone recommend swapping the valves as well as my old head was rebuilt 1k miles ago. Not swapping the heads over, my mechanic says it's too much hassle-so fair play!

What are the benefits from the Mtec I lumps? A few people have mentioned that they are livlier to drive?


Any help will be much appreciated.....


Regards, BJ.
Last edited by BIGJO on Wed Nov 29, 2006 5:47 pm, edited 1 time in total.
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 5:47 pm

The early lump will require a later front pulley, later crank shaft position sensor, and later water pump I THINK, i cant remeber exactly although its easily done mate. ask ant/brianmooore resident hal-e30 bots.
BIGJO
E30 Zone Camper
E30 Zone Camper
Posts: 1191
Joined: Thu Apr 27, 2006 11:00 pm
Location: N.W London & Brighton

Post Wed Nov 29, 2006 5:50 pm

I have all the later bits in my Mtec II engine bay. The only problem is swapping a few of the parts over, correct? Anyone know what the bits are exactly?

I will ask Ant & Brianmoore for help as well...


Regards, BJ.
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Wed Nov 29, 2006 7:10 pm

Dan is spot on, trigger wheel and front sensor, waterpump and the HT leads , other than that drop her in for the full fat 9.75:1 Compression M20

night and day livlier, will seem less torquey though ( its not)

:cool:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 7:12 pm

BIGJO wrote:I have all the later bits in my Mtec II engine bay. The only problem is swapping a few of the parts over, correct? Anyone know what the bits are exactly?

I will ask Ant & Brianmoore for help as well...


Regards, BJ.
iirc, the only problem you will occur upon is torqueing the front pulley; 410n/m i believe is the torque; air gun territory im afraid!!
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Wed Nov 29, 2006 7:15 pm

Not true Dan, the pulleys are held on with 13mm headed M8 bolts, the nose bolt(24mm) can stay put - result

:wink:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
BIGJO
E30 Zone Camper
E30 Zone Camper
Posts: 1191
Joined: Thu Apr 27, 2006 11:00 pm
Location: N.W London & Brighton

Post Wed Nov 29, 2006 7:52 pm

Thanks Ant & Dan. The information provided is much appreciated :wink:


Regards, BJ.