Flywheel help

Need technical Q/A then you're in the right place

Moderator: martauto

Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Tue Nov 28, 2006 10:38 pm

right basicaly i have acquired a m40 flywheel for my 318is which should go well with my new diff, and should also help replace the two tonne rotating mass that is the 12.2 kg m42 dual mass shitter.

The flywheel itself at the moment is 9.7 kg. I have two concerns;

1. How much do i skim it down by; im not concerned about comfort or vibration dampening etc; but i dont want the car to idle like a pig and i don't want it to spin the rear wheels when down shifting; so how light do i go baring in mind its already 9.7?

2. If i do skim it; where abouts do i skim the flywheel itself? obvioulsy the clutch face is going to need a clean up; do i machine the fly from the back face e.g. the face that is facing the engine, of from the sides? or where? i have no idea so someone please help!

Image

Image

Image

Image
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Wed Nov 29, 2006 8:41 am

that lip on the engine side can come off,making it flush with the starter gear ring.And maybe some on the outer edge OD of where the release plate bolts on.Do you have a clutch to fit to it to see if there is any spare material on the OD ?


cheers
andy
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 8:47 am

No clutch at the moment although i will obviously purchase one nearer the fitting time.

I might be able to find out the size though, then i can measure up roughly.

Im really not sure how much to remove though
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Wed Nov 29, 2006 1:11 pm

You'll really need to have it balanced again after machining, you don't want the bugger exploding and taking your ankles off :eek:

Don't take much off the clutch face or the clutch might slip, as has been said take the lip on the engine side down to the starter ring.

Leave the mounting flange well alone too.

Make sure you have it very well clocked up on the lathe or it'll vibrate like fook when engaging/disengaging the clutch. I used a rotary table surface grinder to make sure it's 100% flat after machining.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 1:15 pm

I wont be doing the machining myself so dont worry about that.

i wasnt even going to touch the clutch face; only clean it up slightly; didnt want to skim any off there.

so you reckon get it skimmed then balanced afterwards?
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Wed Nov 29, 2006 1:59 pm

You need to look at how much you can safely remove so that it doesn't burst and then do get it balanced along with the new clutch, crank and front pulley/damper as an assembly :)
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 3:51 pm

you want me to get a new crank and front pulley too? 8O i do have a spare crank!

Maybe i should just bolt on a 9.7 kilo one! instead of skimming it?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Nov 29, 2006 5:00 pm

What about an M20 flywheel? Dont know if it would fit, but you would be able to take a lot more from it than you can from that M40 thing.
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Wed Nov 29, 2006 5:04 pm

:lol: no, just the new clutch cover.
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Wed Nov 29, 2006 5:09 pm

If clocked in acurately enough doing it in a lathe will be acurate and balenced.Its just knowing where to take the material from safely so that it dont go pop !
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 5:20 pm

the m20 flywheel does fit dan but needs a large number of modifications; 323 throw out bearing, m20 starter and a holw host of other stuff. Its common in yank land though.

i will fit a new clutch with it it brown, its just knowing were to skim like andy says. i think the lip should go. is balancing and skimming it a seperate affair then?

sory dont no much about this stuff!
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Wed Nov 29, 2006 5:27 pm

Sort of.when you machine it ,if set correctly it shouldn't need to be balenced.As it is clocked in perfectly there should be no problem.
Like a good quality alloy wheel doesnt need balencing,its the tyre thats put on there that does.
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 5:29 pm

Interesting! so how much do you reckon should be taken off then? considering that installing it in its current state would mean that it would already be 2.5ish kilo's lighter than the stock one? down to 9 kilos or a bit less?
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Wed Nov 29, 2006 5:48 pm

I havent a clue mate.Different engines work better with different weights.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Nov 29, 2006 5:55 pm

You mean release bearing? If you need this and the starter theres not much else to be needed!
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Wed Nov 29, 2006 7:11 pm

DanThe wrote:You mean release bearing? If you need this and the starter theres not much else to be needed!
http://bmw.e30tuner.com/my318is_cur_fly.php
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Nov 29, 2006 9:56 pm

"Clocking" = ?

If it means what i think it means, then "Perfect clocking" has no affect on the balance of a turned part.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Nov 29, 2006 11:14 pm

The 323 release bearing is the same as any other M20 bearing. So you need a flywheel, starter and clutch kit. This would be the best way IMO. The M20 flywheel is lighter to start with and you can remove more material from it, in a safer way.
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Wed Nov 29, 2006 11:27 pm

kam-325i wrote:"Clocking" = ?

If it means what i think it means, then "Perfect clocking" has no affect on the balance of a turned part.
Clocking means using a DTI gauge to measure the run-out ensuring that it's fitted nice and true in the lathe chuck.

A DTI is usually accurate down to 1 um (micrometer).

I machined a couple of M20 flywheels, they were clocked up perfectly (took more time to clock them than to machine them) machined and then setup on a rotary table surface grinder to grind the surface perfectly flat. They were then balanced and were found to be slightly off balance :mad:

New brake discs are ground on a rotary table surface grinder, you can see the unique pattern on the surface. These machines are supremely accurate.

Flywheel balance is critical to engine main bearing shells, for the cost of a cheap night out I wouldn't dream of not having it balanced.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Nov 29, 2006 11:33 pm

Templ8e30 wrote:
kam-325i wrote:"Clocking" = ?

If it means what i think it means, then "Perfect clocking" has no affect on the balance of a turned part.
Clocking means using a DTI gauge to measure the run-out ensuring that it's fitted nice and true in the lathe chuck.

Iain T
Thought it was.....

I know that "out of balance" is caused by slight differences in material density. thats why you might see strange holes drilled around things like flywheels....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Nov 29, 2006 11:39 pm

Who could ballance a flywheel Iain? Engineer's or is it a specialist only job?
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Nov 29, 2006 11:41 pm

A good engineering firm, one's that will do things like cranks should do flywheels aswell....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Thu Nov 30, 2006 12:27 am

I use this firm in Rochdale http://www.impulsedevelopments.co.uk/ma ... rvices.htm

They build race/rally engines for local teams and firms.

What they don't know about engines isn't worth knowing.

Their prices are pretty resonable too.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 12:36 am

DanThe wrote:The 323 release bearing is the same as any other M20 bearing. So you need a flywheel, starter and clutch kit. This would be the best way IMO. The M20 flywheel is lighter to start with and you can remove more material from it, in a safer way.
iv got a m40 flywheel sitting here; or i could go out and find all those bits? im at uni which means i have extremely limited facilities; also i dont want to too light as it will lock up the rear wheels and cause all sorts of nonsense im told; about 8kg is perfect im figuring; the one here is 9.7 so i only have to take 1.7 kg of it which isnt really a lot is it?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Thu Nov 30, 2006 7:11 am

An M20 flywheel is only about 8 kgs to start with
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 10:41 am

DanThe wrote:An M20 flywheel is only about 8 kgs to start with
fair play; but dont you think its rather a lot of hastle to acquire all those bits when iv got one here that bolts up?
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Nov 30, 2006 12:07 pm

dan, whem i changed the clutch on my iS, the flywheel did not seem to be a dual mass type. also, i have a flywheel at work from my rebuild, and this too, does not seem to be dual mass.

i was gonna send my flywheel to sutton rebore, as they do lightening and balancing of many parts.

can somebody please list EVERY part that is needed for an M20 flywheel conversion?
Image
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 1:08 pm

stuartgallafant wrote:dan, whem i changed the clutch on my iS, the flywheel did not seem to be a dual mass type. also, i have a flywheel at work from my rebuild, and this too, does not seem to be dual mass.

i was gonna send my flywheel to sutton rebore, as they do lightening and balancing of many parts.

can somebody please list EVERY part that is needed for an M20 flywheel conversion?
http://www.r3vlimited.com/Tech/318is.htm

I know tims was also a single mass. i think the early ones had them; what reg/year is yours stu? The Etk also showed, iirc, that tims had a dual mass but it didnt!
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Nov 30, 2006 2:04 pm

not a bad website actually. i was under the impression all M20 clutches were the saem, therefore the release bearing will also be the same

so basically, you would need M20 flywheel, M20 complete clutch, and M20 starter motor? will the starter motor fit in the same place as the M42?

also, i've done loadsa M54 clutches, and they use the dual mass flywheel. with these, you can actually move the centre plate with your hands, so you get to feel the take up of the rubber ring between the 2 flywheel plates

i still dont know what im better off doing. i have an M42 flywheel, but im not sure if i should get an M20 setup?

sorry that this isnt really helping you, and hi-jacking your thread?!
Image
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 4:21 pm

stuartgallafant wrote:not a bad website actually. i was under the impression all M20 clutches were the saem, therefore the release bearing will also be the same

so basically, you would need M20 flywheel, M20 complete clutch, and M20 starter motor? will the starter motor fit in the same place as the M42?

also, i've done loadsa M54 clutches, and they use the dual mass flywheel. with these, you can actually move the centre plate with your hands, so you get to feel the take up of the rubber ring between the 2 flywheel plates

i still dont know what im better off doing. i have an M42 flywheel, but im not sure if i should get an M20 setup?

sorry that this isnt really helping you, and hi-jacking your thread?!
it says here:
"The 325i flywheel requires a few other modifications to be fitted in the 318iS. Here's what you need: 325i flywheel, 325i clutch, 325i pressure plate, 325i drive-pinion for the starter motor, and a â€Ëa78-'83 323 throw-out bearing. Replace all these with the 318iS parts and it bolts right together"

so thats what you need; if i had the car in bits i would use the m20 but as it is i might just skim this flywheel to about 8.5 kg and bolt it on.
User avatar
Kos
E30 Zone Team Member
E30 Zone Team Member
Posts: 15448
Joined: Tue Jul 12, 2005 11:00 pm
Location: London / Cyprus

Post Thu Nov 30, 2006 4:31 pm

all IS have a dual mass flywheel dan,

just that some had a lighter one, than others i belive ( to be honets i think it was the later m42 and in the E36 which hav the heavier ones)

as for lightening, it will need to be re-balanced but you will not notice a major difference unless you take off a lot of weight imo

JB racing do a single mass 3kg one for the IS for about 300quid and its mental mate !!

save your beer tokens from th SU bar and get it LoL
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 4:38 pm

3kg? thats just stupid. thats 3/4 of the weight of the one on there; totally silly and would lock up the rear wheels surely and would be useless uphill and would also idle like a pig. I think with 4kg taken off i would notice a bit of a difference mate especially with a different rear diff.now too.

How much shall i machine off do you think? Im pretty sure il machine the one iv got at least i know its going to be ok?
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Nov 30, 2006 4:38 pm

t says here:
"The 325i flywheel requires a few other modifications to be fitted in the 318iS. Here's what you need: 325i flywheel, 325i clutch, 325i pressure plate, 325i drive-pinion for the starter motor, and a â€Ëa78-'83 323 throw-out bearing. Replace all these with the 318iS parts and it bolts right together"
dan, when you buy a clutch, it comes complete as a pressure plate, driven plate and release bearing kit.

kos, im absolutely certain that these flywheels are not dual mass. i'll take a picture of it and post it up, so others can see

also, if you have a dual mass flywheel, the clutch plate does not have torsion springs on it, as the operation/purpose of the dual mass flywheel renders these torsional springs useless. the clutch i fitted to my iS was of the type with the torsion springs in it
Image
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Nov 30, 2006 4:40 pm

Yes the dual mass was fitted to reduce vibration in the four pot (cue mincer jokes) but i dont really give a shit about vibration, or comfort. hence why i want to get rid of it;

re: the clutch stu, i know that, probably means you have to buy a 325i clutch then!
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Nov 30, 2006 4:41 pm

i meant to add, if its easy enough to throw an M20 flywheel setup on there, then im gonna do that

when that bloke mentions the starter pinion, is it just a case of stripping down both starter motors and putting the M20 pinion inside the M42 starter motor?

is there anyone on here that has done it?
Image