325i running like a dog after head swap?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Mal_w
E30 Zone Newbie
E30 Zone Newbie
Posts: 6
Joined: Sat Jan 14, 2006 11:00 pm
Location: FEEL GOOD INC

Post Wed Nov 29, 2006 1:01 am

Hi,

Finaly got the head swapped on my 88 325i touring but now it wont run right at all can be off as many as 3 cyl's usually last 3 in firing order.

The head i put on was a new head a guy had put on and then 6 months later wrecked the car it came complete wit inlet and exhaust manifolds on it (i didn't change these) fitted it all started car she was off cyl's checked all sensors seamed fine noticed crank sensor had fryed wire at the sender after bending it started the car and it ran on all 6 cyl's so i thought that was the prob took it for a run about 3 mile going fine apart from the hesitation when you put your foot down (also poss slight loss of power) then all of a shot back on 4-5 cyl's ordered up a new crank sensor no difference.

Its running really rough and throwing out black smoke with the odd bang al sparks seam to be there any ideas?

Ps
im pretty crap typing so you might need to read that a few times :)
GDBN
E30 Zone Camper
E30 Zone Camper
Posts: 1415
Joined: Fri Apr 08, 2005 11:00 pm
Location: Copenhagen

Post Wed Nov 29, 2006 7:55 am

You sure the crank and cam were at tdc when you put the timing belt back on ?

G
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Nov 29, 2006 9:01 am

Check out the injector/temp sensor plug and socket (fixed to the metalwork under the inlet manifold).
User avatar
Mal_w
E30 Zone Newbie
E30 Zone Newbie
Posts: 6
Joined: Sat Jan 14, 2006 11:00 pm
Location: FEEL GOOD INC

Post Wed Nov 29, 2006 9:43 am

Yep she's dead on tdc.

Brian thats the small round plug under the manifold if so that was corroeded slightly when i undone it first i gave it a clean with wd 40 and connected it up to the plug wich came on the head it was mint is all injector harnesses the same?

Thanks for replys
wildeian
E30 Zone Regular
E30 Zone Regular
Posts: 851
Joined: Thu Mar 09, 2006 11:00 pm
Location: Colchester, Essex

Post Wed Nov 29, 2006 1:05 pm

engine earth strap ok?
User avatar
Mal_w
E30 Zone Newbie
E30 Zone Newbie
Posts: 6
Joined: Sat Jan 14, 2006 11:00 pm
Location: FEEL GOOD INC

Post Wed Nov 29, 2006 3:04 pm

Yep checked that too even used jumpleads as extra earth to be sure.
The car drive in fine apart from the tick of the worn cam however there was certain times when i started it over the past few months that it would only start (somtimes hard to start) on a few cyl's but after a good steady rev it cleared it self each time it has always been down on power from other 325's i had but i always just blamed the worn cam sometimes you could feel it surgeing under hard acceleration you got the sensation it was about to fly but somthing was holding it back.

All this makes me think it's a problem that was there and ive just annoyed it more could it be the ecu?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Nov 29, 2006 7:23 pm

Mal_w wrote: all injector harnesses the same?
All M20s are wired the same in this plug AFAIK.
The engine ECU temperature sensor connections go through this connector, and a poor connection would tell the ECU that the engine is colder than it is. This could result in black smoke.
The injectors are divided into two groups of three. The two batches are fired by two wires in this connector, so a poor connection on one of them would put three cylinders out of action.
User avatar
Mal_w
E30 Zone Newbie
E30 Zone Newbie
Posts: 6
Joined: Sat Jan 14, 2006 11:00 pm
Location: FEEL GOOD INC

Post Wed Nov 29, 2006 11:10 pm

Problem found brian was on the right tracks tried cleaning conectors in that plug no difference so looked at it again decided to pull back rubber seal and there it was 2 wires broke and a 3rd on its way out soldered on couple of temp piggy back wires and all was well apart from a slight miss/hesitencey when you put your foot to the board and a little jumpy when changeing gears under hard acceleration.


thanks brian and everyone else who replyed :cool: