wanted head
be extremely carefull mate if you do chop it off
one slip with the grinder could become very very expensive
if i was closer id come and whip off for ya
is there no one else that can have a bash before you get brutal with it??
exhaust intake manifold.
Moderator: martauto
-
dazleeds
- old skool raver
- Posts: 12883
- Joined: Fri Apr 01, 2005 11:00 pm
- Location: Empire Building @
his next threads gonna read
wanted head
be extremely carefull mate if you do chop it off
one slip with the grinder could become very very expensive
if i was closer id come and whip off for ya
is there no one else that can have a bash before you get brutal with it??
wanted head
be extremely carefull mate if you do chop it off
one slip with the grinder could become very very expensive
if i was closer id come and whip off for ya
is there no one else that can have a bash before you get brutal with it??
www.oldskoolfantasy.co.uk
in the shit,the one to blame,yeh its all my fault ;)
in the shit,the one to blame,yeh its all my fault ;)
-
Jon_Bmw
- Dangerous when thinking
- Posts: 7604
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Salisbury
Again not to state the obvious, but have you tried lying underneath the car with it jacked up a bit. Then its pretty easy to see them/remove them 
-
Martinaston
- E30 Zone Addict
- Posts: 3749
- Joined: Mon Mar 14, 2005 11:00 pm
- Location: London
Small mirror ?
There is NO nucleus.
-
dazleeds
- old skool raver
- Posts: 12883
- Joined: Fri Apr 01, 2005 11:00 pm
- Location: Empire Building @
gooner
at least your not fitting a btb 6 branch mate lol
had a right job doing mine last week
you think the cast job is hard lol try the 6branch mate
ended up with steering coupling off engine mount off and engine jacked up and was still a pain in the arse
at least your not fitting a btb 6 branch mate lol
had a right job doing mine last week
you think the cast job is hard lol try the 6branch mate
ended up with steering coupling off engine mount off and engine jacked up and was still a pain in the arse
www.oldskoolfantasy.co.uk
in the shit,the one to blame,yeh its all my fault ;)
in the shit,the one to blame,yeh its all my fault ;)
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
Thanks all, car is jacked up jon amd ive tried from below and above.Tried hammering socket on ,still no joy.Was going to use hacksaw Daz.Wonder if i can hammer a size 11 socket on?
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
Mmmmmmmmmm, thats someting to look forward to Daz.dazleeds wrote:gooner
at least your not fitting a btb 6 branch mate lol
had a right job doing mine last week
you think the cast job is hard lol try the 6branch mate
ended up with steering coupling off engine mount off and engine jacked up and was still a pain in the arse
-
dazleeds
- old skool raver
- Posts: 12883
- Joined: Fri Apr 01, 2005 11:00 pm
- Location: Empire Building @
wouldnt advise hammering in that area at all mate
are they nuts chewed up??
im off out to play with my zorst in a minute
fortunatly im at the other end of the car tho just replacing a rubber
and straightening my rear box as my pipes look pissed at the moment
are they nuts chewed up??
im off out to play with my zorst in a minute
fortunatly im at the other end of the car tho just replacing a rubber
and straightening my rear box as my pipes look pissed at the moment
www.oldskoolfantasy.co.uk
in the shit,the one to blame,yeh its all my fault ;)
in the shit,the one to blame,yeh its all my fault ;)
-
Jon_Bmw
- Dangerous when thinking
- Posts: 7604
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Salisbury
Another thought use the sockets that look like this:
_
/ \
\_/
Rather than the multi ones(can't think of the proper name.) These are harder to get on, but there is less chances of slipping and rounding with the 6 sided sockets. With a halfords socket set you HAVE to be able to do this job, come on geezer, if you haven't got one they are a 1/3 off at the moment, they are actually really good quality. Shame about having to walk into halfords in the first place though.
Edit:damn that picture of the socket looked really good on my screen
_
/ \
\_/
Rather than the multi ones(can't think of the proper name.) These are harder to get on, but there is less chances of slipping and rounding with the 6 sided sockets. With a halfords socket set you HAVE to be able to do this job, come on geezer, if you haven't got one they are a 1/3 off at the moment, they are actually really good quality. Shame about having to walk into halfords in the first place though.
Edit:damn that picture of the socket looked really good on my screen
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
Cheers Jon, will try that, as it happens ive never had a prob with halfords.
Then again i only ever get stuff like spark plugs from them.
Then again i only ever get stuff like spark plugs from them.