Question about an aparent overheating M40?

Need technical Q/A then you're in the right place

Moderator: martauto

geo1400
E30 Zone Regular
E30 Zone Regular
Posts: 275
Joined: Mon Feb 20, 2006 11:00 pm
Location: Paphos, Cyprus

Post Sun Oct 29, 2006 8:48 pm

Whenever I start my car the temp reading in the cluster works fine, as in it warms up nicely. However once it is actually at operating temp the needle starts jumping irratically. It will creep up to just below the red and then suddenly jump back again. And if you bang (or punch) the dash board it will always return back to the half way point.

Do you think i've got a prob with the sensor or cluster? dry solders or summit? or is my M40 getting all hot bothered?

:cry:
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Sun Dec 03, 2006 12:28 am

Thankfully it looks like you do have just a sensor problem as hitiing the dash won't suddenly 'cool' your car! :D

Have you actually checked to see if your engine is overheating visually/physcially? Pop the bonnet and check for steam or pressure at the rad cap/bleed valve?

My M40 Touring is overheating when stood still despite brand new fan coupling, new water pump and endless coolant fill/bleeding.

Last thing to try is new thermostat and if it's not that I'm in real trouble.

The owner before me obviously used tap water and no anti-freeze as the thermostat housing is caked in limescale. Perhaps this is causing the overheating as the radiator/engine coolant channels could be all clogged up?

Might try flushing the heater matrix too but past this I would be utterly mystified.

Thoughts on geo1400 and my issues?
Jesus325iTouring
Frog freak !
Frog freak !
Posts: 11356
Joined: Sun Jan 09, 2005 11:00 pm
Location: Omnipresent!

Post Sun Dec 03, 2006 12:59 am

Royalratch wrote:Thankfully it looks like you do have just a sensor problem as hitiing the dash won't suddenly 'cool' your car! :D

Have you actually checked to see if your engine is overheating visually/physcially? Pop the bonnet and check for steam or pressure at the rad cap/bleed valve?

My M40 Touring is overheating when stood still despite brand new fan coupling, new water pump and endless coolant fill/bleeding.

Last thing to try is new thermostat and if it's not that I'm in real trouble.

The owner before me obviously used tap water and no anti-freeze as the thermostat housing is caked in limescale. Perhaps this is causing the overheating as the radiator/engine coolant channels could be all clogged up?

Might try flushing the heater matrix too but past this I would be utterly mystified.

Thoughts on geo1400 and my issues?
Sounds like you have the same battle I did,put up with mine for two years of constant coolant top ups,bleeding etc,still didn't suss it out.
Now I have a different engine,i'm part way through stripping my old one down,I'm interested to see what my channels looks like in the head.I'll let you know the result when I have the head off.
Mines an M20 mind,but all the symptons and problems are the same as yours.

geo1400,sounds almost certain you have a loose connection in the back of the cluster,only one half of my cluster comes on until I hit it!
Image

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Sun Dec 03, 2006 9:17 am

Just nip the nut on the back of the temp gauge a little.
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 03, 2006 11:41 am

Definitely the nut on the back of the cluster!
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Tue Dec 12, 2006 7:47 pm

Royalratch wrote:My M40 Touring is overheating when stood still despite brand new fan coupling, new water pump and endless coolant fill/bleeding.

Last thing to try is new thermostat and if it's not that I'm in real trouble.

The owner before me obviously used tap water and no anti-freeze as the thermostat housing is caked in limescale. Perhaps this is causing the overheating as the radiator/engine coolant channels could be all clogged up?

Might try flushing the heater matrix too but past this I would be utterly mystified.

Thoughts on geo1400 and my issues?
Going to finish this this week. Got a new thermostat but was wondering if I need a gasket when reattaching the housing?

Also, have to get 2 threads out the block - stripped 2 heads off as they were quite corroded. I swear they would be too small for a tap and dye.

Any ideas?
geo1400
E30 Zone Regular
E30 Zone Regular
Posts: 275
Joined: Mon Feb 20, 2006 11:00 pm
Location: Paphos, Cyprus

Post Wed Dec 13, 2006 9:15 am

Well guys, I didn't even have a nut on the back of my temp gauge!! So put one on and its workin fine. WHOO!

Royal, are you losing water? white smoke? Head gasket symptoms?

As for the sheared heads, I watched my cousin take a thread out my Cyl head with a good quality (Stanley) fine flat head screwdriver. I think he just patiently etched away at the top of the thread until he grooved a slot, then just unscrewed it!

Good luck and cheers for the help with mine.
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Wed Dec 13, 2006 9:37 am

Nah, the engine runs fine, no smoke, no gunk in the oil and even revs etc. The temp guage creeps up and I switch it off before it gets to the red so I never know how far it will go. I suspect if it's not the thernmostat it's crap in the coolant channles as there's a fair bit of limescale everwyhere. Maybe the radiator is full of crap in that case...

The screwdriver thing is a good idea. It's a bit dark and damp down there and not much space but worth a try - cheers.