That doesn't sound good... (M20 problem)
Moderator: martauto
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
List is complete, I think.
Engine mounts are easy to refit if you slacken the nuts right off at the bottom where they fix to the crossmember as well as removing the top nuts. Easier to refit if you have some help.
Engine mounts are easy to refit if you slacken the nuts right off at the bottom where they fix to the crossmember as well as removing the top nuts. Easier to refit if you have some help.
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Cheers, i've written that down for when I go to the auto factors tomorrow, hopefully they'll have it all in-stock,
That kinda makes sense, guessing you can move them around a bit to get them lined up easier, then tighten the bolts at the same time as lowering the engine and moving it slightly...
Will I need the front of the car lifted up to make it easier (although it would limit the amount I can lift the engine up I think...) because i've got a set of ramps if that is gonna make it easier
That kinda makes sense, guessing you can move them around a bit to get them lined up easier, then tighten the bolts at the same time as lowering the engine and moving it slightly...
Will I need the front of the car lifted up to make it easier (although it would limit the amount I can lift the engine up I think...) because i've got a set of ramps if that is gonna make it easier
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
No advantage in lifting the car, AFAIK. Bonnet off would make life easier.
Holes in the engine mount alloy arms are shaped to make fitting easy. Don't need to tighten any nuts until the engine's sitting on the mounts again.
Be very surprised if anywhere (except possibly GSF/ECP) has a rocker in stock). You should be able to get one of someone on here.
Holes in the engine mount alloy arms are shaped to make fitting easy. Don't need to tighten any nuts until the engine's sitting on the mounts again.
Be very surprised if anywhere (except possibly GSF/ECP) has a rocker in stock). You should be able to get one of someone on here.
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Just got back from trying to get stuff from camberly auto factors, got everything bar the rocker itself (should've checked here before we left :p)
gonna ring gsf now and see...
gonna ring gsf now and see...
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
i like this sort of thing...new lad comes on the site admits he knows very little, asks sensible questions, gets sensible answers, actually bothers to get off his arse to check and find the problem, locates the fault and hopefully rectifies it easily.
mrlee
mrlee

-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Ihave a s/h rocker that I can post,PO is shut now so Monday AM would be the soonest I can help.
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
cheers, gsf had one although i didn't buy it because i wasn't 100% sure it was right (although after spending a couple of hours trying to get one off think it was right after all, so i'll probably just go there and buy it once my housemate returns...
also found out i need a 32mm open ended spanner to take off the fan :p
Basically i've now got to the point of removing the rocker shaft, but i'm a bit stuck, I've taken out the bit of metal that holds them in place and both rubber end bits, but now i can't see a decent way of getting the damn thing out, any hints here?
also is there another way to get the fan off (although i'm thinking it might just be possible to get the belts off around the fan without removing it?
also found out i need a 32mm open ended spanner to take off the fan :p
Basically i've now got to the point of removing the rocker shaft, but i'm a bit stuck, I've taken out the bit of metal that holds them in place and both rubber end bits, but now i can't see a decent way of getting the damn thing out, any hints here?
also is there another way to get the fan off (although i'm thinking it might just be possible to get the belts off around the fan without removing it?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
If all the rockers are free like I described, in theory at least, it should just slide out.
You may have to clean the gunge off it first.
I've come across the odd fan nut where some cowboy has been at it with a cold chisel. Fan spanners are available in Halfords or a motor factors.
Don't forget it's a reverse thread.
You may have to clean the gunge off it first.
I've come across the odd fan nut where some cowboy has been at it with a cold chisel. Fan spanners are available in Halfords or a motor factors.
Don't forget it's a reverse thread.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
There is a tech article on the site that shows this,but I use a long socket extension...but I am working with the head on a bench!!As Brian has said,you need to slide the rocker shaft far enough to free one rocker,can you lever it with a long screw driver?You will need to take off all the spring clips on the shaft you are playing with...open up all the clearances at the ajusters may help to take the strain off any open valves...do NOT turn the cam with the belt off and the head on.The 32mm nut on the fan is a left hand thread.Good luck!!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
You'd have to drill a strategically placed hole in the bulkhead and work from inside the car to do this with the engine in the car, unfortunately!daimlerman wrote:There is a tech article on the site that shows this,but I use a long socket extension!
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Drilling the hole in the bulkhead could work :p
Just been out some more, it is just about loose enough to move, tried using a couple of tools as levers against the bulkhead and got it to move about 1-2mm total, all the rockers are free, to move from side to side, although the way the cam is the broken one is pushing against the top of the valve spring a bit, still possible to move from side to side but it twists the valve spring stuff around with it...
Getting a bit fed up with it and seriously contemplating taking the head off now, from where I am is there much more work to that than undo head bolts and pull?
And if I did do that would it just be head bolts and head gasket needed on top of what i've already got (although still not got the rocker as gsf closed, does your offer still stand daimlerman? and if so how much do you want for it?
Just been out some more, it is just about loose enough to move, tried using a couple of tools as levers against the bulkhead and got it to move about 1-2mm total, all the rockers are free, to move from side to side, although the way the cam is the broken one is pushing against the top of the valve spring a bit, still possible to move from side to side but it twists the valve spring stuff around with it...
Getting a bit fed up with it and seriously contemplating taking the head off now, from where I am is there much more work to that than undo head bolts and pull?
And if I did do that would it just be head bolts and head gasket needed on top of what i've already got (although still not got the rocker as gsf closed, does your offer still stand daimlerman? and if so how much do you want for it?
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Offer still stands,free to a good home,just let me have an address.If you could refund my postage cost I would be grateful.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
To get the head off from where you are, you have to disconnect the exhaust manifold from the downpipes, take off the inlet manifold and everything associated with it, buy new head bolts, drain the coolant and skim the head.
All the rockers can be parked sideways off of the valves to completely take pressure off the shaft.
Keep cleaning the gunge off it, and push it backwards first if necessary - you can lever it over again off the bulkhead.
All the rockers can be parked sideways off of the valves to completely take pressure off the shaft.
Keep cleaning the gunge off it, and push it backwards first if necessary - you can lever it over again off the bulkhead.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Still no PM recieved,I have two cracked heads(sob sob)one is stripped so a single rocker is yours!!
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Hmm, thats a bit odd, could you email me at noskilluk@gmail.com and we can sort it out over email which will hopefully work :p
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
WooHoo, I got my first rocker off, tried pretty much every tool I own to use as a lever to move the rocker shaft and eventually after 45 mins got it far enough to remove the first rocker, the broken one is the fifth rocker along, and soon I think i'll be able to get a hammer and an extension in to make it easier to move the rocker shaft along 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Carefull you don't damage the end of the shaft or it definitely won't slide out.
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Ended up just continuing on levering it out slowly but surely, after taking out the second rocker it got a lot easier and as I removed each rocker in turn it got easier still 
Got all but the end one out (broken one being the last one I removed), In the end I didn't undo the engine mounts and lift the engine, I was prepared to but never needed to, I did have to remove the centre section of the front grill and the rocker shaft pokes out there but it wasn't a problem, any further and the bonnet would've gotten in the way though
Anyway, heres a couple more pics for your enjoyment...
One broken rocker:

One rocker shaft:

I'd like to thank everyone that posted in this thread, might have some more questions to follow but you've all been really helpful in helping me getting this fixed
Got all but the end one out (broken one being the last one I removed), In the end I didn't undo the engine mounts and lift the engine, I was prepared to but never needed to, I did have to remove the centre section of the front grill and the rocker shaft pokes out there but it wasn't a problem, any further and the bonnet would've gotten in the way though
Anyway, heres a couple more pics for your enjoyment...
One broken rocker:

One rocker shaft:

I'd like to thank everyone that posted in this thread, might have some more questions to follow but you've all been really helpful in helping me getting this fixed
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Pink fan!!!!????
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
email just sent.
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Cheers daimlerman, just replied 
More orange/red than pink, phone isn't the best camera :p
More orange/red than pink, phone isn't the best camera :p
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Never seen a BMW fan anything other than black.
That's two things I've learn't from this post then. Wouldn't have thought that the shaft would come out through there.
That's two things I've learn't from this post then. Wouldn't have thought that the shaft would come out through there.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Just been out popping bonnets,both the E30s have black fans but the Daimler has a red one!!
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Well, i'm back
:p
not got it fully fixed yet but the finish line is in sight:
Got all the rockers on,
Got the cambelt back on and checking the TDC marks it looks good
Done the valve clearances
So, my list of stuff to do:
fit the new rocker cover gasket and put the rocker cover back on
Put back the spark plugs (although i've got a set of Bosh Super X 4's iirc, my dad bought these for his old 520i (b reg) and was wondering if they'd fit?)
Refit the radiator and re-fill with coolant
cross every possible body part and turn the key... :s
other than the spark plugs question i've got one other, Is it 'safe' to quickly start the engine without the radiator on there? My thinking is that if there's a problem (which there shouldn't be :p) then i'd rather not have to remove the radiator once more after spending time to re-fit and re-fill it, just being lazy i guess :p
not got it fully fixed yet but the finish line is in sight:
Got all the rockers on,
Got the cambelt back on and checking the TDC marks it looks good
Done the valve clearances
So, my list of stuff to do:
fit the new rocker cover gasket and put the rocker cover back on
Put back the spark plugs (although i've got a set of Bosh Super X 4's iirc, my dad bought these for his old 520i (b reg) and was wondering if they'd fit?)
Refit the radiator and re-fill with coolant
cross every possible body part and turn the key... :s
other than the spark plugs question i've got one other, Is it 'safe' to quickly start the engine without the radiator on there? My thinking is that if there's a problem (which there shouldn't be :p) then i'd rather not have to remove the radiator once more after spending time to re-fit and re-fill it, just being lazy i guess :p
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Put the old spark plugs back in, and refitted and refilled the radiator (not bled as kinda need the engine running to do that)
Anyway gave it a go eventually (bit scared to) and she just turns over and over, seems to get close to running on her own accord but never quite manages it, the exhaust is getting hot so it seems to be firing a bit at least...
Any idea's on this, any chance it could be something really simple like the battery being a little bit too flat, or is it the timing being out, and if thats the case then am I likely to have just messed up my valves/pistons or is it not that bad?
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Recheck the cambelt,its difficult to get it tensioned and in the correct place.Put the battery on charge just in case. Clean the spark plugs,double check the valve clearances-if they are too tight/no existent -no compresion=non starting.Check anything else you may have disturbed,coil lead?H/T leads properly on plugs?What you have done so far is major work that would put lots off,keep your spirit up and keep trying!!Can Briiiiiianmoore think of anything else?
-
ed325i
- E30 Zone Addict

- Posts: 4146
- Joined: Mon Jan 10, 2005 11:00 pm
My 323 has a red/pink fan.Brianmoooore wrote:Pink fan!!!!????
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Fuel lines the wrong way around and plugs on the bracket beneath the diagnostic socket interchanged are the most common.daimlerman wrote:Can Briiiiiianmoore think of anything else?
-
tomson
- E30 Zone Addict

- Posts: 3598
- Joined: Sun Nov 06, 2005 11:00 pm
- Location: Bristol
NoSkill, did you get her running and where abouts do you live?
Tom
Tom
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Not yet, was getting a bit annoyed with it so called it a day...
Looking at your location it would appear I live semi-close to you, Bradley Stoke in bristol (well technically little stoke, but close enough :p)
Looking at your location it would appear I live semi-close to you, Bradley Stoke in bristol (well technically little stoke, but close enough :p)
-
tomson
- E30 Zone Addict

- Posts: 3598
- Joined: Sun Nov 06, 2005 11:00 pm
- Location: Bristol
pi55er mate, you'll get there in the end.
If id read this thread sooner id of offered a hand this weekend but alas its dark now and back to work tomorrow
I live in Bedminster btw, i work in Fishponds.
Tom
If id read this thread sooner id of offered a hand this weekend but alas its dark now and back to work tomorrow
I live in Bedminster btw, i work in Fishponds.
Tom
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Does your engine have a distributer driven from the intermediate shaft?Or is there a H/T type cap on the end of the camshaft?IF the first type,when the belt was slack,you may have upset the ignition timing.....I did that once on an E28 520i.....
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
There was a 'cap' on the end of the camshaft, but didn't look like it did anything? so i'm guessing it's the first type...daimlerman wrote:Does your engine have a distributer driven from the intermediate shaft?Or is there a H/T type cap on the end of the camshaft?IF the first type,when the belt was slack,you may have upset the ignition timing.....I did that once on an E28 520i.....
I didn't touch the fuel lines or the diagnostic socket so don't think it's those...Brianmoooore wrote:Fuel lines the wrong way around and plugs on the bracket beneath the diagnostic socket interchanged are the most common.daimlerman wrote:Can Briiiiiianmoore think of anything else?
I'll look into doing all that at the weekend, got a car for this week and in the course of going to/from and actually doing work that takes up 11 hours of my day, so not really got the time to do it on a weekday...daimlerman wrote:Recheck the cambelt,its difficult to get it tensioned and in the correct place.Put the battery on charge just in case. Clean the spark plugs,double check the valve clearances-if they are too tight/no existent -no compresion=non starting.Check anything else you may have disturbed,coil lead?H/T leads properly on plugs?What you have done so far is major work that would put lots off,keep your spirit up and keep trying!!Can Briiiiiianmoore think of anything else?
For the moment i'm using my housemates car and put my mk1 mr2 into the garage to be mot'd when they have time (should pass easily enough)
I know what you mean about work, I work in trowbridge so it's 30-35 miles there and back each day,tomson wrote:pi55er mate, you'll get there in the end.
If id read this thread sooner id of offered a hand this weekend but alas its dark now and back to work tomorrow![]()
I live in Bedminster btw, i work in Fishponds.
Tom
As above not gonna be doing anything really till the weekend so if you fancy coming over to help then feel free :p
It will live again, it may take time but I will do it :p
-
NoSkill
- E30 Zone Newbie

- Posts: 39
- Joined: Fri Sep 15, 2006 11:00 pm
Just had a look and it seems I got the timing way out somehow I think...
I turned the crank till the dip in the big wheel part was directly under the sensor (I believe thats the TDC sensor so at that position the crank should be at TDC yes?)
And with it like that the arrow on the camshaft sprocket was almost exactly 180 degrees from where it should be, I don't see how I got it that far out but it seems I did, is this likely to have fucked all my valves etc? or am I gonna be lucky in the fact that it's 180 degrees so (i'm thinking hopefully here :p) it was still doing the valves in an order that stopped them hitting the pistons but stopped it firing as well?
either way it seems like I have to take the rad and cambelt off again, fun :p
I turned the crank till the dip in the big wheel part was directly under the sensor (I believe thats the TDC sensor so at that position the crank should be at TDC yes?)
And with it like that the arrow on the camshaft sprocket was almost exactly 180 degrees from where it should be, I don't see how I got it that far out but it seems I did, is this likely to have fucked all my valves etc? or am I gonna be lucky in the fact that it's 180 degrees so (i'm thinking hopefully here :p) it was still doing the valves in an order that stopped them hitting the pistons but stopped it firing as well?
either way it seems like I have to take the rad and cambelt off again, fun :p
