Ok so I've fitted all my power steering bits today
Got to the crank pulley and mine is non pas so only had 1 place for a belt
I have the extra piece of the crank pulley too bolt on too let the pump have a blet
However the bolt holes line up but it seem like either my bolts are too short or its the wrongng pulley can anyone shed some light on this?
M40 engine I should add
318i non pas and pas crank pulley
Moderator: martauto
-
magpie
- Old Skooler
- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
the p/s pulley should bolt on to the crank pulley with those 6 bolts that were included .
i'm not sure why you are having problems
maybe i should of sent both pulley wheels .i'm sure the p/s one is slightly smaller in diameter than the one that is on the crank already but not 100% maybe someone else can shed some light,some pics would be a big help and measure both pulley's ?
i'm not sure why you are having problems
maybe i should of sent both pulley wheels .i'm sure the p/s one is slightly smaller in diameter than the one that is on the crank already but not 100% maybe someone else can shed some light,some pics would be a big help and measure both pulley's ?
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
dje30
- E30 Zone Regular
- Posts: 259
- Joined: Sun Jul 22, 2012 11:00 pm
- Location: gravesend, kent
some pictures here now
can anyone shed some light?
-
magpie
- Old Skooler
- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
measure both pulley's ,
here's a pic that might help ...i'll trawl my archives and see if i have a better one ....
here's a pic that might help ...i'll trawl my archives and see if i have a better one ....
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
magpie
- Old Skooler
- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
dje30
- E30 Zone Regular
- Posts: 259
- Joined: Sun Jul 22, 2012 11:00 pm
- Location: gravesend, kent
now have the pulleys next too eachother
-
dje30
- E30 Zone Regular
- Posts: 259
- Joined: Sun Jul 22, 2012 11:00 pm
- Location: gravesend, kent
magpie wrote:the p/s pulley should bolt on to the crank pulley with those 6 bolts that were included .
i'm not sure why you are having problems
do you have a picture of the other pulley wheel you have?
-
magpie
- Old Skooler
- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
it's been scrapped with the white 318is shell
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
dje30
- E30 Zone Regular
- Posts: 259
- Joined: Sun Jul 22, 2012 11:00 pm
- Location: gravesend, kent
Ahhhhh what did the other pulley look like?
The pulley off my engine can't be separated its one solid unit
And if I sit the pulley you sent onto it they don't fit flush, there's a centimer gap between them
The pulley off my engine can't be separated its one solid unit
And if I sit the pulley you sent onto it they don't fit flush, there's a centimer gap between them
-
magpie
- Old Skooler
- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
clean all the faces up and tap it on with a hammer or get some longer bolts 2 or three and tighten them till it sits flush then undo them and fit the correct 6 bolts i sent.
this is all i can think of for now dude
this is all i can think of for now dude
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
Brianmoooore
- E30 Zone Team Member
- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Duplicate thread in tech. help!