2.5 cam in 2.0

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 4:36 pm

Got a 2.5i intake manifold and a cam sitting there, getting itchy fingers to try it out

Anyone done this, sound like a recipe for disaster?
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Tue Aug 14, 2012 5:09 pm

See about 3/4 of the way down this page:

http://e30tech.com/forum/showthread.php?t=48288

"Originally Posted by mulishaflesh969

10. camshaft - I heard you could use a 325i's camshaft... but what are the advantages of using a camshaft with a higher number? would it benefit the motor any if someone was to spend the extra cash up front for a better cam?

Cams are very important and deserve a separate thread.

The 325i cam will make a lot of low end and midrange torque but fade at top end and probably requires <10:1 CR to run without ignition retard. On a hotter cam you can use more CR and get more top end but may lose some low end depending on how wild you go. Usually a 270-280degree is reasonable”¦anymore than this requires some thought as to the type of power band you want (track car or streetcar). The cam you use also has to match the CR. The last thing you want to do is over cam your m20."
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 5:18 pm

So i could probably run the 2.5 cam reasonably safely, I would see low/midrange benefit but lose a bit off the top end?
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Tue Aug 14, 2012 5:23 pm

verde wrote:So i could probably run the 2.5 cam reasonably safely, I would see low/midrange benefit but lose a bit off the top end?
ask yourself this, if it can be run safely & you may lose some top end but gain some bottom end & midrange, how often will you be using the top of the rev range?? Not very often I bet.
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Tue Aug 14, 2012 5:23 pm

I don't know, that may apply to a stroker (2.7) M20 only.

Where's Ant when you need him?
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 5:27 pm

steve_k wrote:
verde wrote:So i could probably run the 2.5 cam reasonably safely, I would see low/midrange benefit but lose a bit off the top end?
ask yourself this, if it can be run safely & you may lose some top end but gain some bottom end & midrange, how often will you be using the top of the rev range?? Not very often I bet.
Well thats exactly it, im not a fast driver at all, I dont enjoy extreme speed so it really wouldnt bother me

The only worry i have is sticking a piston through the head. If its reasonably safe il give it a try
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Tue Aug 14, 2012 5:32 pm

Andyboy's Restoration Bible says about modifying the 320i:

"fitting a suitable Schrick/Piper/Kent camshaft, such as a 272, will work wonders."

He goes on to say about the 325i:
"a good exhaust, along with a 272 (or 284/272) Schrick camshaft and re-chip..."

So, it would seem that both 320i and 325i use a similar camshaft duration.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 5:40 pm

I might go ahead and do it then. The 325i cam. Order a wild m20b20 chip off yourself. Use the 325i intake aswell? seems slightly wider. That should give me a smoother bottom end with the cam, top end be heightened with the chip. Maybe see if i can get my mate to make up a 6 branch for me
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Tue Aug 14, 2012 5:51 pm

Sounds like a plan. The 325i intake should be useable, though may reduce torque owing to the larger pipes, reducing the airflow speed (venturi effect), so not necessarily what you want on a 320i.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Tue Aug 14, 2012 5:53 pm

i'd just fit a 325i donk and have 50 more ponies ,jobbed. :D
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 5:54 pm

Well il try the cam first. My old man was tryna get me to put that ECU in it that i just sold you to " see what happens " but I cant afford to be taking massive risks. Hence safety being the key point in this operation ha
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Tue Aug 14, 2012 6:44 pm

Do check if there is any variance between a 320 cam and a 325 cam first, if there is only a few degrees difference it will be a lot of work for little benefit.

However i thought the cam you had kicking about was a performance grind of some sort?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 6:59 pm

HairyScreech wrote:Do check if there is any variance between a 320 cam and a 325 cam first, if there is only a few degrees difference it will be a lot of work for little benefit.

However i thought the cam you had kicking about was a performance grind of some sort?
I have a high lift and a regular one. I dont have the scratch to do another engine swap just now and when i do itl be m52. Just wondered if i could make use of the parts i have for now
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Tue Aug 14, 2012 7:23 pm

ahh fair enough, there are a few cam profiles in my 2.8 thread around page 5-10 if you have a hunt, i think reggid may have done a 320 cam.

If you are going to stick one in though don't expect marvels, the 320 engine is maimed by its small valves.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 7:40 pm

Yeah im not expecting huge results just want to get the most out of it. Il buy one of speedtouches chips too and see if I can borrow a btb 6 branch. A family friend is a shit hot machinist/welder and could make a replica
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
ross_jsy
Married to the E30 Zone
Married to the E30 Zone
Posts: 7307
Joined: Sun Jul 12, 2009 11:00 pm
Location: Jersey, C.I.

Post Tue Aug 14, 2012 8:19 pm

Pay for postage and I'll lend you one bud
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Tue Aug 14, 2012 8:23 pm

i wouldn't copy a btb3 directly for a 320, primary's will be too large and i expect the length to be off.
i can run a 325 cam with 320 valve sizes and stroke through pipemax later on and tell you sizes and lengths latter on if you want.

Then its just a case of make them fit.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 9:05 pm

HairyScreech wrote:i wouldn't copy a btb3 directly for a 320, primary's will be too large and i expect the length to be off.
i can run a 325 cam with 320 valve sizes and stroke through pipemax later on and tell you sizes and lengths latter on if you want.

Then its just a case of make them fit.
Pipemax? Thatd be cool of you man. If i had a rough idea of lengths that would be needed im sure gary could rattle one up for me.


Might not be necessary if the lengths wont be any good for motor Ross, thanks for the offer though. Not many people would lend a btb to be cloned!
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Tue Aug 14, 2012 10:00 pm

Length might be similar, as they are due a lot to CR, cam timing and valve/port size, so they may either be very similar or a hell of a difference.

Pipemax is a header design software.
http://maxracesoftware.com/pipemax36xp2.htm
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Tue Aug 14, 2012 10:06 pm

My brain literally blew out the back of my head. I suppose i could just give it a crack. If i get more power and its all good, woohoo, if not...well i may put an m20b25 in again one day so il save it for then!
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
BATTS91
E30 Zone Squatter
E30 Zone Squatter
Posts: 1764
Joined: Sat May 01, 2010 11:00 pm
Location: clacton on sea essex

Post Wed Aug 15, 2012 1:41 am

Your still on this 2l ? The money ur spending on things u dnt need on the car could be towardsa real engine , ie m50/52
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Wed Aug 15, 2012 3:18 am

the 320i (L) cam is almost identical to the 325i (K) except the 320i one has a 4 degree advance built in probably to help with the lower displacment. You can use a B25 cam but dont expect much difference.
E30 325is with M20B31
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Wed Aug 15, 2012 3:23 am

HairyScreech wrote:i wouldn't copy a btb3 directly for a 320, primary's will be too large and i expect the length to be off.
i can run a 325 cam with 320 valve sizes and stroke through pipemax later on and tell you sizes and lengths latter on if you want.

Then its just a case of make them fit.
BTB3 are too big for a 2.5L TBH even though they work well in midrange and topend. I guess they wanted to cater for the 2.7+ crowd aswell.
E30 325is with M20B31
ross_jsy
Married to the E30 Zone
Married to the E30 Zone
Posts: 7307
Joined: Sun Jul 12, 2009 11:00 pm
Location: Jersey, C.I.

Post Wed Aug 15, 2012 8:14 am

BATTS91 wrote:Your still on this 2l ? The money * I tried to use text speak but the text speak filter stopped me * spending on things u * I tried to use text speak but the text speak filter stopped me * need on the car could be towardsa real engine , ie m50/52
All this isn't costing much/out of parts he has knocking around. An m5x conversion will cost around £2k to do properly not including things like brakes and suspension, plus he doesn't have a license, not going to be able to insure a converted car
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Wed Aug 15, 2012 10:36 am

ross_jsy wrote:
BATTS91 wrote:Your still on this 2l ? The money * I tried to use text speak but the text speak filter stopped me * spending on things u * I tried to use text speak but the text speak filter stopped me * need on the car could be towardsa real engine , ie m50/52
All this isn't costing much/out of parts he has knocking around. An m5x conversion will cost around £2k to do properly not including things like brakes and suspension, plus he doesn't have a license, not going to be able to insure a converted car
Exactly. I dont wanna go mental right away, most people start in a 900 polo or something, iv jumped into a 2l rwd notoriously tail happy car, and as ross says iv got all these things floating around so its costing nothing to tweak a little.
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
mcbonio
E30 Zone Squatter
E30 Zone Squatter
Posts: 1868
Joined: Sun Feb 12, 2012 11:00 pm

Post Wed Aug 15, 2012 11:00 am

Verde,
If you want more power than what the m20b20 offers, you really won't get it by bolting m20b25 parts to it. You're wasting your time mate.

Better spend this time you're wasting and go source a nice m50b28 engine and gear box and get that in. Instant 190 bhp from a much more modern and powerful engine 24v engine.

Or if you want to keep it original and do an easier conversion source M20b25 and drop that in.

:cool:
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Wed Aug 15, 2012 11:08 am

Alright man thanks. It did have an m20b25 when I bought it, but it blew up and I had a spare 2 litre so I dropped it in. My mates possibly turning his e36 into an m3 so he offered to give me his 2.5 engine. Tht might be worth using?
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
ross_jsy
Married to the E30 Zone
Married to the E30 Zone
Posts: 7307
Joined: Sun Jul 12, 2009 11:00 pm
Location: Jersey, C.I.

Post Wed Aug 15, 2012 11:34 am

I used an m50 (2.5 from an e36) as I want to boost it eventually. Nowt wrong with an m50 and they are bullet proof. Can get more power easily out of an m52 though and it's a lighter engine but I wouldn't turn my nose up at an m50 especially if it's free.

It's a fair chunk of change to do properly though, and if funds are tight I wouldn't bother for now. Also you will need to consider things like 51mm struts/rear disc conversion if your car doesn't have them already and that all adds up
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Wed Aug 15, 2012 11:58 am

Iv got lots of room so I might just take it and it can sit til im ready. I already have the big struts but I need disks on the back. When I bought the car it had around 190hp and drum rear brakes :s harrowing combination
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
mcbonio
E30 Zone Squatter
E30 Zone Squatter
Posts: 1868
Joined: Sun Feb 12, 2012 11:00 pm

Post Thu Aug 16, 2012 11:58 pm

Yep, was a bloke on here selling a 540i big brake conversion. Stopping is always a good idea.!

My first e36 had a m50b25 lump in, was a lovely engine, pulled like a train. Extremely well made engine.
BATTS91
E30 Zone Squatter
E30 Zone Squatter
Posts: 1764
Joined: Sat May 01, 2010 11:00 pm
Location: clacton on sea essex

Post Fri Aug 17, 2012 2:16 am

My whole m50 conversion. cost around £800 Tops! , its all about who you know ! And what u can do yourself , i done exhaust ,wiring all myself its easy tbh just save sone more n do it euan , would waste time and money upgrading a 2L .ever heard of pissing in the wind lol
BATTS91
E30 Zone Squatter
E30 Zone Squatter
Posts: 1764
Joined: Sat May 01, 2010 11:00 pm
Location: clacton on sea essex

Post Fri Aug 17, 2012 2:19 am

Oh and im using 318is brakes which being on 51mm legs i presume are the same calipers as 325 , and some cheap drilled and grooved discs ! I stop fine ;)
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Fri Aug 17, 2012 10:43 am

Only 800 quid? Thats fuck all. Would be even less if kamil gave me his 2.5 for free
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift
ross_jsy
Married to the E30 Zone
Married to the E30 Zone
Posts: 7307
Joined: Sun Jul 12, 2009 11:00 pm
Location: Jersey, C.I.

Post Fri Aug 17, 2012 11:24 am

Don't forget insurance Verde, you won't get insured on a converted car and it isn't worth the risk
User avatar
verde
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5438
Joined: Thu Aug 25, 2011 11:00 pm
Location: The Sticks

Post Fri Aug 17, 2012 11:33 am

Yeah good point, no danger. The 2 litre in the 1.6 is bad but the 2.5 would be ridic. It wouldnt be til next year atleast.
Marrakesh brown tech 2 LSx loading.....
Raise hell praise Dale.
North East Drift Club - Hollerboys Drift