M42 cam cover bolts

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

User avatar
Emm3
E30 Zone Regular
E30 Zone Regular
Posts: 866
Joined: Sat Apr 08, 2006 11:00 pm

Post Tue Aug 14, 2012 12:06 am

Hello all,

I've changed the cam cover gasket on the I.s together with the gaskets for the plugs. Luckily I did some research as to what was involved with the job before I refit and I've read so many horror stories about stripped threads due to over tightening. If I hadn't read up I would have probably overtightened the bolts too. Now I've got all the bolts back In and they have all threaded in fine which is good but I darent tighten them with a wratchet just in case I knacker a thread, so far I've tightened them by hand with just the extension bar and socket but don't know if it's enough to seal

Your advice please
DHFiS
Old Skooler
Old Skooler
Posts: 2733
Joined: Sat Aug 12, 2006 11:00 pm
Location: cambridge

Post Tue Aug 14, 2012 8:14 am

Mine are only hand tight and I havent had problems. Might be worth putting a bit of thead lock on them but the rubber round the bolt seems to stop the vibration loosening mine.
jimbom30cab
Tech 1 freak
Posts: 7631
Joined: Mon Oct 12, 2009 11:00 pm
Location: in the garage

Post Tue Aug 14, 2012 8:32 am

yer i think you have done it enough, give it a run and it should not leak
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Aug 14, 2012 9:07 am

if you're going to do much work on cars, you should really invest in a torque wrench, but as a general rule, the correct torque for a nut or bolt is that which you can apply with one finger hooked over a 'standard' length spanner for the size of fastener in question.
No thread lock required, and FAR more damage is caused on vehicles by fasteners being overtightened than under tightened.
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Tue Aug 14, 2012 9:58 am

you can give it a nip with 1/4 " ratchet ,just a quarter turn and it's sealed .

all this talk of finger tight on an m42 screamer.They will rattle loose and leak leaving you to clean it all up and if your on a long drive and don't notice the smell of burning oil , bang goes your Donk .

fire it up and check for leaks before driving,give it some revs when warmed up as we don't drive around on tick over do we .

NEXT! :D
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
User avatar
Emm3
E30 Zone Regular
E30 Zone Regular
Posts: 866
Joined: Sat Apr 08, 2006 11:00 pm

Post Tue Aug 14, 2012 11:00 am

Brianmoooore wrote:if you're going to do much work on cars, you should really invest in a torque wrench, but as a general rule, the correct torque for a nut or bolt is that which you can apply with one finger hooked over a 'standard' length spanner for the size of fastener in question.
No thread lock required, and FAR more damage is caused on vehicles by fasteners being overtightened than under tightened.
Got a torque wrench Brian but I wasn't sure on using it as I thought the threads may have weakened over time with heat and may not be as strong?
User avatar
Emm3
E30 Zone Regular
E30 Zone Regular
Posts: 866
Joined: Sat Apr 08, 2006 11:00 pm

Post Wed Aug 15, 2012 12:28 am

Well I had to use the wratchet as the hand tightening technique did not work started the car and it burnt oil like mad as the plug gaskets were not sealing due to the bolts between the plugs not being tight enough, the oil dribbled down onto the plug and then into the bore. I did them up until I could feel the resistance, fired the car up and voila no leaks and no oil burning. I've removed the throttle body heater plate and all the nasty pipe work the car idles so perfect now
appletree
E30 Zone Addict
E30 Zone Addict
Posts: 3479
Joined: Fri Jan 20, 2006 11:00 pm
Location: Retford

Post Wed Aug 15, 2012 4:47 am

Even in the worse case of one stripping you can buy a helly coilset as I had to as mine had 3 stripped threads when I got it.
Image

You should never underestimate the predictability of stupidity

M42 Supercharged 285bhp + M3 6speed box