Powder coated engine parts?
Moderator: martauto
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Hello all I've just had the cam cover and inlet manifold powder coated in black but the company that have done this didn't mask the underside so there is like an over spray also where the gasket fits on the cam cover, they have coated the area where the seal fits my concern is will the seals for the cam cover and spark plugs still seal? Regarding the overspray if its left on will the oil eventually breakdown the powder coating that in turn will end up around the engine?
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Id be more concerned about whats inside the manifold, especially if they sandblasted it
-
staley_turbo
- E30 Zone Camper

- Posts: 1391
- Joined: Tue Jan 19, 2010 11:00 pm
- Location: Leicester
Its worth cleaning the gasket area, as when the engine gets hot, it could melt the powder again. I usually mask everything off first.
-
staley_turbo
- E30 Zone Camper

- Posts: 1391
- Joined: Tue Jan 19, 2010 11:00 pm
- Location: Leicester
I washed mine out with water as much as I could,DanThe wrote:Id be more concerned about whats inside the manifold, especially if they sandblasted it
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
I wouldn't use it until you know 100% that it's clean! I know of a few guys who's engines got destroyed because of powdercoat overspray getting into the engine.
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Well a word of advice ask your powdercoater to do the masking before you end up in worse shit. I was not going to leave that over spray on so I thought id clean the underside of the cam cover my mistake instead of using soap and a wire brush I used carb cleaner within half an hour all of that on the under side started to peel off like rubber the bad bit was through the oil filler hole the carb cleaner got to the face and it left white marks all over it which wouldn't come off so I gave it back to the coaters to re-do And I asked them to mask this time 
-
G-Bear
- E30 Zone Squatter

- Posts: 1631
- Joined: Wed Mar 12, 2008 11:00 pm
- Location: Hertfordshire
Surely they should be doing that for free, or is clumsy overspray accepted as part of the process...?
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
They're charging a tenner to re do so it's ok
-
G-Bear
- E30 Zone Squatter

- Posts: 1631
- Joined: Wed Mar 12, 2008 11:00 pm
- Location: Hertfordshire
Good work (although I don't how much powder coating is), it's always a pain chasing up things like that but worth it if you get something back without it getting sour..
-
rix313
- E30 Zone Team Member

- Posts: 4970
- Joined: Fri Oct 31, 2008 11:00 pm
- Location: Silverstone
Surely powder coat shouldn't fall off if it comes into contact with carb cleaner. I'd be taking the parts some where else.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
All depends what's in the carb cleaner, some of them have some fairly nasty shit in.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&


