waxoyling help
Moderator: martauto
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
basically i was going to do a quick engine swap and other bits and pieces, however ive decided to just take my time and do it properly, just invested in my first oyster card to get around, so looks like im doing a full resto!
engine and box/ struts are coming out, im going to clean and degrease the whole engine bay front arches and front floor tomorrow,
question is can i get a scraper on the arches and floorpan get rid of all th shit then get some degreaser on then a final pressure wash,
i have a 1litre tin of hammerite underbody seal, in some threads people have crisp clean arches, is that hammerite? and in other threads people claim waxoyl is sticky and collects dust and crap...
i plan to apply black hammerite to all four arches and underside, btw rear subframe is also coming off,
so are there any sections in particular i should coat the shit out off?
also once the engine bay is clean, can i apply clear waxoyl around it, etc on chassis legs, under the legs, on the front valance and will i have an issue with the heat coming off the manifold burning the waxoyl up?
can i also coat the front subframe in standard hammerite direct 2 rust paint,
will try make up a wiki page as well on waxoylin,
engine and box/ struts are coming out, im going to clean and degrease the whole engine bay front arches and front floor tomorrow,
question is can i get a scraper on the arches and floorpan get rid of all th shit then get some degreaser on then a final pressure wash,
i have a 1litre tin of hammerite underbody seal, in some threads people have crisp clean arches, is that hammerite? and in other threads people claim waxoyl is sticky and collects dust and crap...
i plan to apply black hammerite to all four arches and underside, btw rear subframe is also coming off,
so are there any sections in particular i should coat the shit out off?
also once the engine bay is clean, can i apply clear waxoyl around it, etc on chassis legs, under the legs, on the front valance and will i have an issue with the heat coming off the manifold burning the waxoyl up?
can i also coat the front subframe in standard hammerite direct 2 rust paint,
will try make up a wiki page as well on waxoylin,
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
I've used Smoothrite on loads of cars including my E30 on bits you can't see - its good stuff as long as you prep the area properly - and although you can paint over rust if its anything more than light surface rust forget it. I did my front subframe with it and have also done battery trays on numerous cars with it - followed by a thick coating of waxoyl applied with a paintbrush
Waxoyl is fine under the arches - get it up on axle stands with the wheels off, get the pressure washer in there and get it squeaky clean - you may need a stiff brush and several applications of TFR to get it properly clean.
Cover the brakes with a carrier bag before you go anywhere near it with the waxoyl and I would suggest brushing it on to all the flat surfaces and use a compressor to get it into any box sections.
As a rule of thumb I would "coat the shit out of" any area that already looks rusty AFTER you've prepped it and made sure its not rotten
Waxoyl is fine under the arches - get it up on axle stands with the wheels off, get the pressure washer in there and get it squeaky clean - you may need a stiff brush and several applications of TFR to get it properly clean.
Cover the brakes with a carrier bag before you go anywhere near it with the waxoyl and I would suggest brushing it on to all the flat surfaces and use a compressor to get it into any box sections.
As a rule of thumb I would "coat the shit out of" any area that already looks rusty AFTER you've prepped it and made sure its not rotten

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
DO NOT use a Schultz type underseal on your car! (Which I suspect this Hammerite under body seal is).
This stuff starts to lift after a couple of years, trapping water underneath it, and hastening the final demise of the car.
This stuff is aimed at scrap yard dodging Fords and the like, trying to prolong the life of these wrecks for a couple more MOTs.
I'm currently getting through litres of white spirit removing this muck from a design cab. I'm restoring, before repairing the polyurethane OE underseal with the correct materials. If it wasn't for this stuff, the restoration would have been finished weeks ago.
This stuff starts to lift after a couple of years, trapping water underneath it, and hastening the final demise of the car.
This stuff is aimed at scrap yard dodging Fords and the like, trying to prolong the life of these wrecks for a couple more MOTs.
I'm currently getting through litres of white spirit removing this muck from a design cab. I'm restoring, before repairing the polyurethane OE underseal with the correct materials. If it wasn't for this stuff, the restoration would have been finished weeks ago.
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
The Hammerite Underseal stuff doesnt fully dry. I've used it on my car and it remains slightly tacky, but not enough for stuff to stick to it.
@Brianmooore - This stiff doesnt 'lift' as it doesnt dry. If it was to lift, then who ever put it on did it wrong and didnt clean it properly. If applied to a nice clean surface there wont be any issues.
@OP - Its a very messy job but looks great when its done. I used it when I first got my chromie and only just gone over it all again and there was no evidence of it lifting or letting anything in, the rust patchs I found under it where previously there
@Brianmooore - This stiff doesnt 'lift' as it doesnt dry. If it was to lift, then who ever put it on did it wrong and didnt clean it properly. If applied to a nice clean surface there wont be any issues.
@OP - Its a very messy job but looks great when its done. I used it when I first got my chromie and only just gone over it all again and there was no evidence of it lifting or letting anything in, the rust patchs I found under it where previously there
-
rich318i
- E30 Zone Addict

- Posts: 2393
- Joined: Wed Oct 26, 2005 11:00 pm
- Location: Brands :) :)
the clue is in the name wax oil, comes back to life in hot weather
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
its "hammerite under body seal with added waxoyl" , its not just waxoyl- which is a totaly different product
inside the arches, you want to use a proper sealant, 1st fully taking back removing the old factory stuff- rust can start underneath that
inside the arches, you want to use a proper sealant, 1st fully taking back removing the old factory stuff- rust can start underneath that
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
go on, say it Carl, ffff, ffff,ffff,ffffERTAN!

-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
-
Rich320I
- E30 Zone Camper

- Posts: 1272
- Joined: Tue Dec 06, 2011 11:00 pm
- Location: Worcester
ha ha i love fertan iv been liebrally spraying it on anything suspicious looking on my new one, so basically the whole car is now covered in fertan 
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
^ that was going to be my next question, I've scoured it and got rid of most of the grease and dirt, there's no rust at all apart from some spots appearing on the subframe, looks very solid underneath and along the sills,
There was a loose bit of the BMW undersell I pulled it off like plasticy stuff, tbh is there nothing I can use over it to fill in where it's come off?
It looks like it's done a pretty good job tbh protecting it for 20 odd years! I don't want to be scraping it all off and leaving it prone to rust, I take it this underseal is all along the floorpan and rear arches etc,
Anything i can add to it, and fill in the few spots of underseal that came off
Any suggestions?
There was a loose bit of the BMW undersell I pulled it off like plasticy stuff, tbh is there nothing I can use over it to fill in where it's come off?
It looks like it's done a pretty good job tbh protecting it for 20 odd years! I don't want to be scraping it all off and leaving it prone to rust, I take it this underseal is all along the floorpan and rear arches etc,
Anything i can add to it, and fill in the few spots of underseal that came off
Any suggestions?
-
Blitz
- Married to the E30 Zone

- Posts: 11151
- Joined: Mon Jan 30, 2006 11:00 pm
- Location: East London+Basildon
Any broken under seal just reseal it with a polyurethane based under seal. I hate it when I see these nasty black Hammerite stuff underside of the car. Waxoyl or any other rust protection wax for box sections, hidden areas, under body kits, arch lips and fixings like brake pipes. No need to put it over under seal.
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
How many years ago did you first apply it to your car Jim? It does dry out and it does lift off, ive seen loads of cars that have had it chucked at them, f**king horrible stuff and a complete waste of time, clear waxoil is what you want, when warm its like water and will run into any seam/opening it can, once it has dried its just a wax coating, doesnt fall off and repels water.Jim320i wrote:The Hammerite Underseal stuff doesnt fully dry. I've used it on my car and it remains slightly tacky, but not enough for stuff to stick to it.
@Brianmooore - This stiff doesnt 'lift' as it doesnt dry. If it was to lift, then who ever put it on did it wrong and didnt clean it properly. If applied to a nice clean surface there wont be any issues.
@OP - Its a very messy job but looks great when its done. I used it when I first got my chromie and only just gone over it all again and there was no evidence of it lifting or letting anything in, the rust patchs I found under it where previously there
I use TFR and degreasing products as little as possible, all you are doing is removing any protection from the seams/sections it runs into.
A wire brush and WD40 is plenty good enough to clean any crud off with
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
is there a product name i can search, or somewhere i can get the stuff? typed in google nothing came up about poly under seal,
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
@Dan - Would have been January 2010 I last put it on so over 2 years and it was still the same tackiness when I first put it on.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
http://www.estore-central.com/bmw-acces ... rotection/
this the stuff im looking for? black undercoating
this the stuff im looking for? black undercoating
