My car was a 318i auto and am doing m52 swap and swaping brakes and suspension to 325i. My car does not have ABS but 325i set up has sensors in place. Would it be worth me fitting ABS system? I will be using the car for fast road and occasional track action.
Thanks in advance. John
Converting to 325i disc set up, ABS?
Moderator: martauto
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
It's a pretty heavy task to retrofit, and personally I loathe ABS so for me it would be a no
-
johnmaccow
- E30 Zone Regular

- Posts: 351
- Joined: Mon Aug 23, 2010 11:00 pm
- Location: Gateshead
Thanks mate. Doing a bit research it seems a lot of people remove it for track. 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I'm going to present the exact opposite view! Whereas ABS has no advantage on a track, and lengthens the braking distances of a competent driver, when it comes to a car used on public roads, ABS should be compulsory, IMHO.
On a track, all braking is done in a straight line, as it ideally should also be on the road, but when the unexpected happens, ABS performs tricks that no human can do, however good a driver they may be.
I've just retrospectively fitted ABS to a 1.8i auto, as it happens, as part of a full rebuild.
On a track, all braking is done in a straight line, as it ideally should also be on the road, but when the unexpected happens, ABS performs tricks that no human can do, however good a driver they may be.
I've just retrospectively fitted ABS to a 1.8i auto, as it happens, as part of a full rebuild.
-
johnmaccow
- E30 Zone Regular

- Posts: 351
- Joined: Mon Aug 23, 2010 11:00 pm
- Location: Gateshead
Is it a hard task to retrofit ABS? Am aslo looking at rx7 front set up so don't know if its actually worth doing.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Not all front legs and disc braked rear trailing arms are drilled for the ABS sensors, and even those that are may not have bearings fitted with ABS toothed rings, but on the car I've just converted, I was changing these for a spare set that did have the ABS bits anyway, and this was really what prompted the rest of the ABS conversion.
I cut the pump mounts off of a scrap shell and welded them into position, acquired the pipes from the same source, and the loom plus ECU came from 'stock'.
I cut the pump mounts off of a scrap shell and welded them into position, acquired the pipes from the same source, and the loom plus ECU came from 'stock'.
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
I had the fear with regards to plumbing a pump in, the extra lines needed I imagine would be a dear do from BMW & making them up could lead to one messy looking install. You're right though Brian, my dad (in the early years of ABS) had a truck force him onto the central reservation, he slammed on with 2 wheels on the tarmac and didn't stop talking about it for weeks..
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Emergency braking with two wheels on tarmac and two on loose gravel or grass is an almost daily occurrence for me, with the type of single track road/blind corners I do a lot of my local driving on. ABS gets well used!
-
johnmaccow
- E30 Zone Regular

- Posts: 351
- Joined: Mon Aug 23, 2010 11:00 pm
- Location: Gateshead
The rear arms and front legs have the ABS rings all in place just no sensors. I was planning on renewing the brake lines for copper ones anyway. If it wouldnt be too bad to fit the pump and fit the loom in then I may consider it
.
-
cypriot_boy_2k7
- E30 Zone Squatter

- Posts: 1641
- Joined: Mon Jan 29, 2007 11:00 pm
If you need a kit as in sensors, ecu, pump, wiring send me a PM
