Quick question - radiator cap issue

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Sun Jul 15, 2012 9:51 pm

Hi, I have a 318i m40 and have recently replaced the rad cap (expansion tank cap). Now though I have noticed that when I squeeze the radiator hose air comes out of the rad cap then sucked back in when I let go. Quite freely, no pressure required at all.

Basically, is this normal? I don't remember noticing this before.

Thanks

Dan
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Sun Jul 15, 2012 9:58 pm

sure it's the cap? if so, check it's freely screwing down & there are 2 O rings present.

secondly make sure it has a yellow part on the inside - these are the recall version.

if you're not completely sure, check the cross-head bleed screw, right next to the cap..
User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Mon Jul 16, 2012 7:53 am

Hi,

Thanks for the reply. It's definately the cap. There are two o-seals present and it screws down tight. It's the yellow version too as I only replaced it about a week ago because I don't think it was before.

For info, the bleed screw is fine.
mani
E30 Zone Camper
E30 Zone Camper
Posts: 1143
Joined: Mon May 26, 2008 11:00 pm
Location: London

Post Mon Jul 16, 2012 8:26 pm

could need a washer
User avatar
Billwill
E30 Zone Regular
E30 Zone Regular
Posts: 363
Joined: Sun Jun 26, 2011 11:00 pm
Location: South Africa

Post Tue Jul 17, 2012 8:38 am

I just checked the cap on my M40....fairly new from BMW.

It has the yellow plastic inside section and has "140" stamped on it.

Has two O rings and a large black rubber washer that seals tightly on the inner rim of the bottle when screwed down tight.

Maybe they have given you a faulty part? :?
User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Tue Jul 17, 2012 1:04 pm

Thanks for checking yours.

I'm starting to doubt my radiator to be honest, I've borrowed a rad cap from an E46 (same cap, different pressure "200") and put that on. Screwed it up tight but can still squeeze the hose easily expelling air out of the rad cap.

I put my hand over the hole and squeezed the hose, no leaks at all but with a cap on air flows freely. I'm wondering if the thread is too long or tank neck too wide or something. Whatever it is, neither cap seals the system.
User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Tue Jul 17, 2012 1:14 pm

Just to confirm, if you squeeze either the in or out hose on the radiator, is air supposed to blow/suck from the radiator cap easily?

Thanks
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jul 17, 2012 1:28 pm

DanTheDoc wrote:Just to confirm, if you squeeze either the in or out hose on the radiator, is air supposed to blow/suck from the radiator cap easily?

Thanks
With the cap in place, air can enter reasonably easy, but you shouldn't be able to expel it.
User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Tue Jul 17, 2012 3:49 pm

Right, thanks. Something is definately up then because I can expel air incredibly easily by squeezing any coolant hose. I'm going to put my old expansion tank back on and see what that does.

Thanks everyone, I'll keep you posted.

Dan
User avatar
DanTheDoc
E30 Zone Newbie
E30 Zone Newbie
Posts: 73
Joined: Fri Oct 21, 2011 11:00 pm
Location: Wells, Somerset

Post Wed Jul 18, 2012 8:33 am

Well, the rad cap turned out to be fine.

I put the old radiator back in and bled the system and all seems to be ok (with the exception of the original leak).

So, to sum up, got sent a faulty radiator. And you CANNOT get the coolant system functioning correctly when the radiator cap does not seal, it just pi**es out everywhere!

Thanks for the replies

Dan