How come BMW engines sit at an angle?
Moderator: martauto
-
Adammcf
- E30 Zone Squatter

- Posts: 1578
- Joined: Sun Jan 23, 2005 11:00 pm
Just wondering that Ive noticed that nearly all BMW engines except the biggest ones tend to sit tilted over at an angle in the engine bay instead of sitting vertical like most other cars.
Only reason I can think of is that the inlet manifolds are alot bigger than the exhausts and by tilting it over towards the exhaust side it makes more room for the inlet and also balances the engine over the crank.
Only reason I can think of is that the inlet manifolds are alot bigger than the exhausts and by tilting it over towards the exhaust side it makes more room for the inlet and also balances the engine over the crank.
-
d6dph
- Married to the E30 Zone

- Posts: 12435
- Joined: Sun Aug 14, 2005 11:00 pm
- Location: Tiptree. Essex
rb26 skyline engines and sr20 200sx engines sit at a similer angle.
Dont know why, just thought id share that with you!!
Dont know why, just thought id share that with you!!

-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
cosworth engines sit slightly out of line aswell, no idea why though.
-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
Also, if they were upright, it would cause some problems shutting the bonnet! The inlet manifold get's very close to the bonnet on the M20, and on the E30 M3, you leave anything on the plenum, and you'll have nice dent in your bonnet!

-
koos
- E30 Zone Regular

- Posts: 584
- Joined: Wed Jun 29, 2005 11:00 pm
- Location: Crawley, West Sussex
-
Adammcf
- E30 Zone Squatter

- Posts: 1578
- Joined: Sun Jan 23, 2005 11:00 pm
Suppose, never thought of that one.
-
swindy
- E30 Zone Regular

- Posts: 574
- Joined: Fri Feb 11, 2005 11:00 pm
- Location: Lancashire
Check out almost any VW engine, they are the same, the most I have ever seen in fact, and the audi quattro engines are on a major tilt, I gotta back the other two, sat upright deffinately wouldnt fit under the bonnet.
Mark
Mark
"We aint here for a long time, we're here for a good time."
"Don't take life too seriously, you'll never get out alive."
"Don't take life too seriously, you'll never get out alive."
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Its to reduce the height of the engine, if you no what i mean...
When a car is designed, they look at the visual aspect first, mechanical later, if a current engine will do the job, but to tall to fit, they will tilt it to fit, or redesign a current engine to fit the car.
Otherwise the E30 would have a nice power bulge in the bonnet......
When a car is designed, they look at the visual aspect first, mechanical later, if a current engine will do the job, but to tall to fit, they will tilt it to fit, or redesign a current engine to fit the car.
Otherwise the E30 would have a nice power bulge in the bonnet......
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Its for weight distribution.
Andrew
Andrew
-
Geeman
- Married to the E30 Zone

- Posts: 7641
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Grimsby, Lincolnshire
weight distribution....?
I don't follow... surely if it was upright, the same amount of weight is spread over the front axle.
Are you on about spreading the weight from one side of the car to the other...? Surely that's not a good thing to do...
I don't follow... surely if it was upright, the same amount of weight is spread over the front axle.
Are you on about spreading the weight from one side of the car to the other...? Surely that's not a good thing to do...
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
You want as much of the wight as close to the ground as you can get it.
Andrew
Andrew
-
Geeman
- Married to the E30 Zone

- Posts: 7641
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Grimsby, Lincolnshire
Aaaaaaah, I getcha now.
-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
As for the weight distribution, it goes againts RHD cars, as the engine leans over to the right, in a LHD car, the driver helps balance the weight distribution out, this would also explain why most cars in rallying/touring car are LHD.

-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Most cars are LHD because 95% of the world drives on the wrong side of the road !!!
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Dude i cant say thats true as the S14 has perfect 50/50 weight distribution at the front when the engine is sitting on the cross member.Simon wrote:As for the weight distribution, it goes againts RHD cars, as the engine leans over to the right, in a LHD car, the driver helps balance the weight distribution out, this would also explain why most cars in rallying/touring car are LHD.
Andrew
-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
I read this on S14, I'm pretty sure you commented on the thread, it mentioned the fact that with a driver sitting in the seat (LHD) the car was perfectly balanced!Demlotcrew wrote:Dude i cant say thats true as the S14 has perfect 50/50 weight distribution at the front when the engine is sitting on the cross member.Simon wrote:As for the weight distribution, it goes againts RHD cars, as the engine leans over to the right, in a LHD car, the driver helps balance the weight distribution out, this would also explain why most cars in rallying/touring car are LHD.
Andrew

-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
Even cars built for motorsport in RHD countries though...kam-325i wrote:Most cars are LHD because 95% of the world drives on the wrong side of the road !!!

-
Martinaston
- E30 Zone Addict

- Posts: 3749
- Joined: Mon Mar 14, 2005 11:00 pm
- Location: London
mY first guess was to keep the low profile of the bonnet, but thinking about it the top of the engine is quite low anyway, it's just the manifold that sticks up so surely they could have designed it to sit even lower.
So i'd say it's due to the weight issue, shame it leans the wrong way though
So i'd say it's due to the weight issue, shame it leans the wrong way though
There is NO nucleus.
-
DieselMeister
- E30 Zone Regular

- Posts: 388
- Joined: Sat Nov 12, 2005 11:00 pm
The way I understand it is that it's 99% about weight distribution. Tilted engine = lower centre of gravity, which in turn means better stability and agility. It's the very same reason BMW puts the battery in the boot and especially important with long, tall engines like straight sixes.
To oversimplify, equal (or as close to) weight distribution and the lowest possible low C of G means better handling.
Shame they gave the E30 steering from a cruise liner....
To oversimplify, equal (or as close to) weight distribution and the lowest possible low C of G means better handling.
Shame they gave the E30 steering from a cruise liner....
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
You've got that mod aswell then !!!DieselMeister wrote:
Shame they gave the E30 steering from a cruise liner....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Thing is SI, most race cars use coilovers which can adjust corner weights and ARB preloads, so even if this was true and the engine was making the car heavy to one side it would be corrected when they adjust the suspension on the scales. When I was messing about with my engine I found it to have really good balance from left to right with all the associated parts attached and lifted up by the two jacking points on the block and on the front timing covers.Simon wrote:I read this on S14, I'm pretty sure you commented on the thread, it mentioned the fact that with a driver sitting in the seat (LHD) the car was perfectly balanced!
Andrew
-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
OK then, I think it was a good theory!Demlotcrew wrote:Thing is SI, most race cars use coilovers which can adjust corner weights and ARB preloads, so even if this was true and the engine was making the car heavy to one side it would be corrected when they adjust the suspension on the scales. When I was messing about with my engine I found it to have really good balance from left to right with all the associated parts attached and lifted up by the two jacking points on the block and on the front timing covers.Simon wrote:I read this on S14, I'm pretty sure you commented on the thread, it mentioned the fact that with a driver sitting in the seat (LHD) the car was perfectly balanced!
Andrew

-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Two reasons:
1, lower centre of gravity for engine.
2, To make the engine fit under the bonnet.
Thats it...........
1, lower centre of gravity for engine.
2, To make the engine fit under the bonnet.
Thats it...........
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Simon
- E30 Zone Team Member

- Posts: 14939
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: South Wales
And to make access to the dipstick easier..kam-325i wrote:Two reasons:
1, lower centre of gravity for engine.
2, To make the engine fit under the bonnet.
Thats it...........

-
TheDutch
- E30 Zone Regular

- Posts: 433
- Joined: Sat Jan 15, 2005 11:00 pm
It seems to me that this statement:
equates to:Demlotcrew wrote:even if...the engine was making the car heavy to one side it would be corrected when they adjust the suspension on the scales
Demlotcrew wrote:with good suspension the weight distribution of a car is irrelevant
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
^ Not quite, as we are talking about very small amount of weight. As there are other counter balance parts on the car (Exhaust, petrol tank, battery, electrics)
Andrew
Andrew
-
Adammcf
- E30 Zone Squatter

- Posts: 1578
- Joined: Sun Jan 23, 2005 11:00 pm
So I was pretty much right then. 
Its just that when you compare the engine on a 325 for example the angle at which it is tilted at is alot more than most other rwd cars.
Its just that when you compare the engine on a 325 for example the angle at which it is tilted at is alot more than most other rwd cars.
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Have you seen the tilt on some of the older peugot diesel engine ?
Looks like 45Ԛ°.
Looks like 45Ԛ°.
Last edited by kam-325i on Mon Dec 05, 2005 2:21 pm, edited 1 time in total.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
TheDutch
- E30 Zone Regular

- Posts: 433
- Joined: Sat Jan 15, 2005 11:00 pm
OK Andy that's true, just wanted to make sure you weren't enjoying a day out at the Fantasy Dreamworld theme park!
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
Just to throw this into the mix, My E36 M3 Evo engine when sitting on the ground and at the correct angle only has ever such a slight tendancy to fall over, i.e. you can hold it up with one finger kind of thing.
I'd say that it is just to keep the weight and bonnet line low.
Surely they wouldn't have designed it to counter balance the weight of the driver as the mass of the average bratwurst eating Geman could vary hugely!
I'd say that it is just to keep the weight and bonnet line low.
Surely they wouldn't have designed it to counter balance the weight of the driver as the mass of the average bratwurst eating Geman could vary hugely!
-
MrDazzle
- E30 Zone Regular

- Posts: 451
- Joined: Fri Oct 21, 2005 11:00 pm
- Location: On the path to the dark side
You think that's bad...look at the angle at which they mount the engines in their bikes 

As others have said...it's too lower the CoG and improve packaging. I cannot recall ever seeing a car (or indeed, vehicle of any kind!) with a perfectly upright engine. Upright inline anyway...v's are usually upright, but that's like two inlines cranked

As others have said...it's too lower the CoG and improve packaging. I cannot recall ever seeing a car (or indeed, vehicle of any kind!) with a perfectly upright engine. Upright inline anyway...v's are usually upright, but that's like two inlines cranked
-
Fushion_Julz
- E30 Zone Camper

- Posts: 1295
- Joined: Tue Jun 07, 2005 11:00 pm
- Location: Blackwater
The Nissan 200sx S13 has a perfectly upright engine....inline 4
The old mini also had a perfectly upright engine...transverse 4
Mk2 Jags...inline 6
probably plenty of others, too...either where the motor is not too tall or where the bonnet line is high...
The old mini also had a perfectly upright engine...transverse 4
Mk2 Jags...inline 6
probably plenty of others, too...either where the motor is not too tall or where the bonnet line is high...
1987 Henna Rot M3 (was 195bhp CAT..now more and no cat)
2001 E46 330i SE Touring (manual)
2001 E46 330i SE Touring (manual)
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
For our RHD cars the battery should be on the passenger side really, lazy Germans !
Impractical for a road car but i'd guess the best place for it would be in a battery box mounted to the rear passenger foot well ?
I'd love to get my car corner weighed, not that i could make much improvements/adjustments as my car stands but still interesting.
Impractical for a road car but i'd guess the best place for it would be in a battery box mounted to the rear passenger foot well ?
I'd love to get my car corner weighed, not that i could make much improvements/adjustments as my car stands but still interesting.
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
aye, in addition to the direction in which the motor leans, that choice (e30's anyway) is due to manifold routing & servo linkage..Simon wrote:Even cars built for motorsport in RHD countries though...kam-325i wrote:Most cars are LHD because 95% of the world drives on the wrong side of the road !!!
On the engine lean, in addition to the above points, the mount arms offer greater torsional resistance. win win really..



