Erratic temp gauge

Need technical Q/A then you're in the right place

Moderator: martauto

Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Thu Jul 12, 2012 10:24 pm

So for a long time now I have been putting up with a rather erratic temp gauge. Basically it stays steady rising to operating temperature between the half and 3/4 mark.

It's fine for about 10 mins then starts bouncing all over the place, if I stop the gauge immediately settles back to around half way. It's worse at motorway speeds than around town.

I removed the cluster and tightened the brass nut on the back and that has made no difference.

There is no signs of a failed head gasket I.e no mayo in the oil, no oil residue in the coolant, no loss of coolant and no white smoke.

I'm not 100% sure the viscous is OK though as I tried the test of the old rolled up newspaper and it did stop the fan but not immediately.

So all I can think of is possibly a failing water pump making the temperature erratic or the brown sensor is playing up.
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Thu Jul 12, 2012 10:27 pm

I should also mention that the timing belt, tensioner and all v belts were replaced less than 200 miles ago, but I did not replace the water pump as it looked fairly recent.
User avatar
bimanut
E30 Zone Camper
E30 Zone Camper
Posts: 1194
Joined: Thu Oct 30, 2008 11:00 pm
Location: Warrington

Post Fri Jul 13, 2012 2:25 pm

might be a daft thing to say but you say you tightened the brass nut and not plural there are two brass nuts.Had the same problem one of my mine was missing :eek:
Image
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Fri Jul 13, 2012 2:37 pm

On the back of the cluster there was only one nut directly behind the guage on the outer casing of the cluster.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jul 13, 2012 6:35 pm

Pull the plug off of the brown sensor, and connect a 330 or 470 ohm resistor between the single pin in the plug and a good earth. This should make the gauge read somewhere in the middle section when the ignition is turned on.
If the reading is stable, then the brown sensor is probably faulty. If it's still jumping, then further investigation is needed.
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Fri Jul 13, 2012 9:26 pm

Thanks Brian looks like its off to the electrical store tomorrow to source one, I'll post back once I know more.
User avatar
harry_p
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5313
Joined: Thu Oct 12, 2006 11:00 pm
Location: norfolk

Post Fri Jul 13, 2012 10:10 pm

I've had a broken wire under the rubber boot just behind the plastic connector on the temperature sensor cause the exact same symptoms.
cheers,

harry
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Fri Jul 13, 2012 11:47 pm

Thanks harry_p that's something for me to look for tomorrow as well.