help wanted with electric hood and mechanisms
Moderator: martauto
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
Hi as title suggests, I'm looking for some help gettin my electric hood workin, the previous owner has taken parts off, and I don't know where to start and what I need, firstly I am missing the hydraulic horseshoe catches, secondly one motor (in boot) is loose, the other the arm isn't connected that folds the roof down, also the cable isn't attached on the other side to pull the horseshoe up and down.
Is there anyone that can help me with this if I pay them cash, or alternatiely provide a detailed diagram of all hood mecahnisms and parts so I can work out what its supposed to look like, what goes where and what I am missing.
I have almost all the spare parts from the first hood-relay, both motors, metal wire, hood ecu control board etc.
Thank-you
Matt
Is there anyone that can help me with this if I pay them cash, or alternatiely provide a detailed diagram of all hood mecahnisms and parts so I can work out what its supposed to look like, what goes where and what I am missing.
I have almost all the spare parts from the first hood-relay, both motors, metal wire, hood ecu control board etc.
Thank-you
Matt
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
it's hydraulic?

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
if the k reg car in your sig pic is the one in question it will be an electric roof, hydraulic ended at about F/G reg.
I have loads of details and pics for electric roof as mended mine after being in a similar position. Let me know and I can email you any details you need.
I have loads of details and pics for electric roof as mended mine after being in a similar position. Let me know and I can email you any details you need.
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
It would be good if you could post them here. This question gets asked a lot.ben9040 wrote:
I have loads of details and pics for electric roof as mended mine after being in a similar position. Let me know and I can email you any details you need.
Ben
-
Mo13
- E30 Zone Regular

- Posts: 722
- Joined: Tue Apr 03, 2012 11:00 pm
- Location: East London
I say post them on here and get grrrmachine to WiKi itBenHar wrote:It would be good if you could post them here. This question gets asked a lot.ben9040 wrote:
I have loads of details and pics for electric roof as mended mine after being in a similar position. Let me know and I can email you any details you need.
Ben
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
there are loads of threads if you search including one by me about how I mended it. The drawings of the mechanisms are on the BMW fans website and are quite good
This one shows the two arms and the levers for the hood
http://bmwfans.info/parts/catalog/E30/C ... _assembly/
And this one for the horseshoe
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
I did a write up here and try to reply to hood threads so search under my name for more details.
This one shows the two arms and the levers for the hood
http://bmwfans.info/parts/catalog/E30/C ... _assembly/
And this one for the horseshoe
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
I did a write up here and try to reply to hood threads so search under my name for more details.
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
-
Mo13
- E30 Zone Regular

- Posts: 722
- Joined: Tue Apr 03, 2012 11:00 pm
- Location: East London
Great stuff!!!
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
based on experience from here if the hood is no longer working and various parts have been removed then chances are the roof motor top has sheared.
This is actually quite an easy repair with the strengthening plate (bought from German ebay as cheaper than UK).
You must keep the parts well oiled (see servicing guide in wiki) and help the roof to fold by giving it a helping push on the way down (as it is this part of the process that can cause the roof arm to bend and puts stress on the motor). You push the top in the air at the front to help the motor and arm deal with the strain through the heaviest lifting.
I have had mine mended for a few years now and have had no other problems with it once mended. With a bit of care and attention there really is no need for a manual conversion.
Note this is all based on an electromechanical hood. I am unsure about the hydraulic version.
This is actually quite an easy repair with the strengthening plate (bought from German ebay as cheaper than UK).
You must keep the parts well oiled (see servicing guide in wiki) and help the roof to fold by giving it a helping push on the way down (as it is this part of the process that can cause the roof arm to bend and puts stress on the motor). You push the top in the air at the front to help the motor and arm deal with the strain through the heaviest lifting.
I have had mine mended for a few years now and have had no other problems with it once mended. With a bit of care and attention there really is no need for a manual conversion.
Note this is all based on an electromechanical hood. I am unsure about the hydraulic version.
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
Hi Ben9040, unfortunately, all the images that need to be shown are missing from the above write up.ben9040 wrote:http://www.e30zone.net/modules.php?name ... highlight=

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
Thanks for this, but some of the pictures seem to have gone AWOL.ben9040 wrote:http://www.e30zone.net/modules.php?name ... highlight=
It would be good if we could get it all in the wiki to preserve them.
Ben
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
not sure why that is as my account is still active with the pictures still in.
I am happy to email them to someone to add to the wii but have never been able to figure out how it works to update it!
I am happy to email them to someone to add to the wii but have never been able to figure out how it works to update it!
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
I've PMed Grrrmachine asking him to look at getting this wikified.
Ben
Ben
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
Why not stick them in this thread for now?ben9040 wrote:not sure why that is as my account is still active with the pictures still in.
I am happy to email them to someone to add to the wii but have never been able to figure out how it works to update it!
Ben
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
i cant do it on my work computer but will have a look later today or i can send the pics to someone else to upload.
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
How much did you pay for the second hand chicken drumstick shaped lever, Ben?

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
I think it was about £20 second hand. German ebay is the best e.g. see
http://www.ebay.de/itm/BMW-E30-318i-320 ... 3f19b7eaa4
http://www.ebay.de/itm/BMW-E30-Cabrio-H ... 2c66a84d98
http://www.ebay.de/itm/BMW-E30-Cabrio-R ... 4167afc3c7
my german isnt great but e30 cabrio verdeck is e30 convertible top and is a good starting point. A quick email to see how much overseas postage would be and you are away!
Those second hand parts are the levers. The rods are harder to find and the thicker top hood one is the one that usually bends and hence is usually knackered. These are still available from BMW directly though for about £40.
http://www.ebay.de/itm/BMW-E30-318i-320 ... 3f19b7eaa4
http://www.ebay.de/itm/BMW-E30-Cabrio-H ... 2c66a84d98
http://www.ebay.de/itm/BMW-E30-Cabrio-R ... 4167afc3c7
my german isnt great but e30 cabrio verdeck is e30 convertible top and is a good starting point. A quick email to see how much overseas postage would be and you are away!
Those second hand parts are the levers. The rods are harder to find and the thicker top hood one is the one that usually bends and hence is usually knackered. These are still available from BMW directly though for about £40.
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
Advise on this, please, Ben. You see the circular disk, it sits higher than it should, so when the roof is closed, the top "drumstick shaped" lever catches. Any ideas on what may be causing it to do that?
You can also see that it has already had the repair plate fitted.

You can also see that it has already had the repair plate fitted.


PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
Cheers Ben. For some reason, the image I just posted ^^ isn't showing - probably a photbucket issue! 
showing now. Any ideas?
showing now. Any ideas?

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
In Ben's linked thread he mentions a washer under the main arm.Gert_8 wrote:Advise on this, please, Ben. You see the circular disk, it sits higher than it should, so when the roof is closed, the top "drumstick shaped" lever catches. Any ideas on what may be causing it to do that?
You can also see that it has already had the repair plate fitted.
Another Ben
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
i fitted a spacer washer in the motor hole where the drumstick lever slots in and also on the end of the drumstick lever where the roof rod fits. This lifts the drumstick lever and the roof rod up a few mm and prevents anything catching.
I cant see your pic on my work computer but i assume the circular disc is the disc screw that holds the triangular lever down. This needs to be screwed in tight as possible using a small screwdriver or similar that will fit in the hole in the disc. This should fit flush with the lever.
I cant see your pic on my work computer but i assume the circular disc is the disc screw that holds the triangular lever down. This needs to be screwed in tight as possible using a small screwdriver or similar that will fit in the hole in the disc. This should fit flush with the lever.
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
Hi Ben,
You got it right, the circular disc is the problem, so I'll try the washer solutions. However, I have noticed that when the circular disc is screwed down as far as it will go, it's not flush, it has a slight lip to one side, which suggests that the thread has a problem - this hasn't always been the case. Do you think the motor needs to be removed (that it fits into) from the boot?
If I can resolve this, I think I may be able to resynch and get things moving again. Thanks for your help. Sorry for the hijack, but hopefully Matt's problem is electromech, rather than hydraulic, so he finds this useful.
You got it right, the circular disc is the problem, so I'll try the washer solutions. However, I have noticed that when the circular disc is screwed down as far as it will go, it's not flush, it has a slight lip to one side, which suggests that the thread has a problem - this hasn't always been the case. Do you think the motor needs to be removed (that it fits into) from the boot?
If I can resolve this, I think I may be able to resynch and get things moving again. Thanks for your help. Sorry for the hijack, but hopefully Matt's problem is electromech, rather than hydraulic, so he finds this useful.

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
the disc screws into the strengthening plate not the motor. Thats the whole point of the plate as the original point on the motor always shears.
The second pic in this german ebay link shows the plate. It should have a brass washer over the mounting screw input on the plate which the triangular lever fits onto. The round screw thing then screws into the plate. Mine goes in flush so it is either a missing brass washer (as the washer raises the triangular lever), a knackered thread in the plate, a blockage in the plate screw hole or a knackered round screw.
The second pic in this german ebay link shows the plate. It should have a brass washer over the mounting screw input on the plate which the triangular lever fits onto. The round screw thing then screws into the plate. Mine goes in flush so it is either a missing brass washer (as the washer raises the triangular lever), a knackered thread in the plate, a blockage in the plate screw hole or a knackered round screw.
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
Cheers Ben - both Bens!ben9040 wrote:the disc screws into the strengthening plate not the motor. Thats the whole point of the plate as the original point on the motor always shears.
The second pic in this german ebay link shows the plate. It should have a brass washer over the mounting screw input on the plate which the triangular lever fits onto. The round screw thing then screws into the plate. Mine goes in flush so it is either a missing brass washer (as the washer raises the triangular lever), a knackered thread in the plate, a blockage in the plate screw hole or a knackered round screw.

PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
PeteE30Tourer
- E30 Zone Camper

- Posts: 1317
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: Dorset
This is all great stuff! I really must get mine sorted. I've got the kit from german ebay, so all I need to do is fit it and get it all working. I think the problem I'll have is that the fabric of the hood doesn't fold naturally in the right way. I've tried the "crimping" mod, but this hasn't helped sadly. I found another website form the US that showed using wide elastic strips with velcro on the ends to help pull back the bar that is supposed to swing back - got all that sorted, but it's the fold in front of this that doesn't fall in place right.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
Apologies for the thread hi-jack by the way, but I've suggested before that all roof problems should be collated in one place for future beneficiaries.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
Apologies for the thread hi-jack by the way, but I've suggested before that all roof problems should be collated in one place for future beneficiaries.

Back behind an M20, but now I can hear it better.
-
PeteE30Tourer
- E30 Zone Camper

- Posts: 1317
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: Dorset
This is all great stuff! I really must get mine sorted. I've got the kit from german ebay, so all I need to do is fit it and get it all working. I think the problem I'll have is that the fabric of the hood doesn't fold naturally in the right way. I've tried the "crimping" mod, but this hasn't helped sadly. I found another website form the US that showed using wide elastic strips with velcro on the ends to help pull back the bar that is supposed to swing back - got all that sorted, but it's the fold in front of this that doesn't fall in place right.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
Apologies for the thread hi-jack by the way, but I've suggested before that all roof problems should be collated in one place for future beneficiaries.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
http://bmwfans.info/parts/catalog/E30/C ... lding_top/
Apologies for the thread hi-jack by the way, but I've suggested before that all roof problems should be collated in one place for future beneficiaries.

Back behind an M20, but now I can hear it better.
-
PeteE30Tourer
- E30 Zone Camper

- Posts: 1317
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: Dorset
Sorry - something weird going on here - typed a long response and submitted it, but it comes up as a blank post! Copied the text to a new reply and that's now blank too! Wassup??

Back behind an M20, but now I can hear it better.
-
PeteE30Tourer
- E30 Zone Camper

- Posts: 1317
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: Dorset
This is all great stuff! I really must get mine sorted. I've got the kit from german ebay, so all I need to do is fit it and get it all working. I think the problem I'll have is that the fabric of the hood doesn't fold naturally in the right way. I've tried the "crimping" mod, but this hasn't helped sadly. I found another website form the US that showed using wide elastic strips with velcro on the ends to help pull back the bar that is supposed to swing back - got all that sorted, but it's the fold in front of this that doesn't fall in place right.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
Does anyone have part 25 of the horse-shoe exploded view (link below) fitted? I don't have this and if I'm right, this should prevent the horse-shoe lifting mechanism from catching/rubbing on the roof fabric when folded away. My roof has sadly got a small tear now where this has been rubbing too much.
Last edited by PeteE30Tourer on Wed Jul 11, 2012 12:35 pm, edited 1 time in total.

Back behind an M20, but now I can hear it better.
-
PeteE30Tourer
- E30 Zone Camper

- Posts: 1317
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: Dorset
WTF??!! Just tried again and it's still coming up blank. I give up. Hopefully I'll see you on Sunday Matt so we can compare notes.

Back behind an M20, but now I can hear it better.
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
To be honest mate this is what I thought also, because then we can put cars side by side and see what I'm missing and I'll bring my digital voltmeter down and check all the voltages etc, both of the motors, are now working after alot of fiddling and changing one motor for a spare I had.PeteE30Tourer wrote:WTF??!! Just tried again and it's still coming up blank. I give up. Hopefully I'll see you on Sunday Matt so we can compare notes.
so we are getting somewhere, but my horseshoe cable has snapped and missing some bits and bobs.
-
stew72
- E30 Zone Regular

- Posts: 653
- Joined: Fri Dec 02, 2011 11:00 pm
I had similar issues to you matt, with parts being removed and also found that the spigot on the motor had sheared. In my case the control unit is also suspect, the gas struts that should help the hood mechanism are weak and I can't get the hood to fold consistantly so that it wouldn't trap so to save the hassle I just converted the horseshoe to work off a switch and fold it down manually.
-
ben9040
- E30 Zone Newbie

- Posts: 222
- Joined: Thu Apr 17, 2008 11:00 pm
- Location: Newcastle
I have a few spares in my garage including horseshoe cables etc so if you are missing anything I might be able to provide it for a reasonable price, let me know ideally with pics if something is broken or what you think is missing and I can see if I have it.
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
I've PMed my email to you if you want me to try and put the missing pictures up.ben9040 wrote:not sure why that is as my account is still active with the pictures still in.
I am happy to email them to someone to add to the wii but have never been able to figure out how it works to update it!
Ben
-
Gert_8
- Married to the E30 Zone

- Posts: 11302
- Joined: Mon Dec 08, 2008 11:00 pm
- Location: In your back passage faster than a rat up a drainpipe!
For those of you that might be interested - I discovered ONE of the problems that is stopping my roof operating properly....
Thanks for the link Ben, I ordered the replacement plate this morning. Once this arrives and is fitted, I'll try to reengage the motors and keep my fingers crossed...! Cheers.
1. Plate has been distorted (see gap, which should be perfectly flat)

2. This above causes this..

3. The actual pivot post is at an angle, therefore the brass collar has a slight lip.

4. Which raises the circular disc in my earlier image, that then catches the drumstick shaped upper lever to catch on the roof closing movement.


Thanks for the link Ben, I ordered the replacement plate this morning. Once this arrives and is fitted, I'll try to reengage the motors and keep my fingers crossed...! Cheers.
1. Plate has been distorted (see gap, which should be perfectly flat)

2. This above causes this..

3. The actual pivot post is at an angle, therefore the brass collar has a slight lip.

4. Which raises the circular disc in my earlier image, that then catches the drumstick shaped upper lever to catch on the roof closing movement.



PONY, 2013 - "Anyway span 360 degrees hitting the kerb and giving the old man two fingers as I was spinning like Michael Schumacher would
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
thanks for your help guys, I also need the strengthening plate, the horseshoe motor bolts and possibly the horseshoe wire looks like it has broken.
Where do you find the allen key to close the horseshoe and lock it manually??
cheers
Where do you find the allen key to close the horseshoe and lock it manually??
cheers
