Is there any point in getting a poly bush for the lsd?
Moderator: martauto
-
si911t
- E30 Zone Regular

- Posts: 634
- Joined: Thu Oct 07, 2010 11:00 pm
- Location: Lancashire
I am in process of ordering some front end polybushes and was wondering if there is any real benefit of spending up to £30 on a lsd poly bush ??
-
DHFiS
- Old Skooler

- Posts: 2733
- Joined: Sat Aug 12, 2006 11:00 pm
- Location: cambridge
If your rubber diff bush is wrecked the 2 part poly bush is easier to fit into the ali diff back cover. To fit the Z3M bush you need to press it in which is best done with the cover off the diff.
-
harry_p
- Engaged to the E30 Zone

- Posts: 5313
- Joined: Thu Oct 12, 2006 11:00 pm
- Location: norfolk
from what i have seen, the diff bush doesnt last well at all, seen several pictures of sagging ones. better off getting a new rubber one. i think the z3m one might be stiffer?
but they are a bit of a sod to get out and back in without cracking the alloy backplate.
but they are a bit of a sod to get out and back in without cracking the alloy backplate.
cheers,
harry
harry
-
Kos
- E30 Zone Team Member

- Posts: 15448
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: London / Cyprus
Do not fit a polly diff bush, they fail and can cause damage
Buy a ZM one and fit it. It's 1" tops to change if you have access to a press.
Buy a ZM one and fit it. It's 1" tops to change if you have access to a press.
-
DHFiS
- Old Skooler

- Posts: 2733
- Joined: Sat Aug 12, 2006 11:00 pm
- Location: cambridge
Z3M Diff bush P/N 33172228425 £95.00
-
ANDY325TOURING
- E30 Zone Regular

- Posts: 380
- Joined: Sun Jan 08, 2006 11:00 pm
- Location: Norn Iron
Its a tad pricey.....
-
harry_p
- Engaged to the E30 Zone

- Posts: 5313
- Joined: Thu Oct 12, 2006 11:00 pm
- Location: norfolk
didnt realise they were quite that much.
how much is a standard e30 one? i'd have thought a nice new one of those would be a decent improvement over a 20 year old one.
how much is a standard e30 one? i'd have thought a nice new one of those would be a decent improvement over a 20 year old one.
cheers,
harry
harry
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Standard one is more than adequate for any standard or near standard E30, but only attempt to change it with the back plate off of the car.
-
PG325
- E30 Zone Camper

- Posts: 1194
- Joined: Sat Jun 06, 2009 11:00 pm
Z3M bush (33172228425) last year when I bought one from Cotswold was £25.03 delivered.
I put the bush in the freezer for an hour, pressed it in with a bench vice, nice easy job.
I put the bush in the freezer for an hour, pressed it in with a bench vice, nice easy job.
-
ANDY325TOURING
- E30 Zone Regular

- Posts: 380
- Joined: Sun Jan 08, 2006 11:00 pm
- Location: Norn Iron
Exactly my point im sure i didnt pay anything like that much before!
-
DHFiS
- Old Skooler

- Posts: 2733
- Joined: Sat Aug 12, 2006 11:00 pm
- Location: cambridge
£95 is what Coopers BMW are selling them for.
-
Duke137
- Married to the E30 Zone

- Posts: 7207
- Joined: Sat Aug 29, 2009 11:00 pm
I'm in the wrong job!DHFiS wrote:£95 is what Coopers BMW are selling them for.
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
-
penton08
- E30 Zone Camper

- Posts: 1206
- Joined: Sat May 10, 2008 11:00 pm
The z3m diff bush went from under £30 to £90 odd about 3 months agoANDY325TOURING wrote:Exactly my point im sure i didnt pay anything like that much before!
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
The diff bush needs to move in harmony with the beam bushes. Fitting a Polly diff bush with stock beam bushes is probably what causes the sagging and rapid wear as the diff bush will be working too hard as its stiffer and limiting the beam movement. With Polly beam bushes as well they should split the load between them.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
