fixtures and fittings re build !
Moderator: martauto
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
finished off stripping the car today- last job was taking front/rear bumpers/kit apart and putting them inside the car, cars ready to roll out to paint shop and hes waiting for it, just waiting on a mate to take it up there on the truck
so now.. i have pretty much aquired all the parts and morsels i need, and have all sorts of boxes of fittings, so many nuts and bolts, things like head light units need refurbing, powder coating the plates and a few other parts, and new fittings etc, and then a case of cleaning and refurbing and wrapping/boxing up every part from the car along with a nice clear out of the garage and new shelving and storage ideas, so when the car comes back....i aim to haver a 100% clean and tidy garage with all the parts clean wrapped and ready to put on like new carefully and orderly boxed and stored in some sort of order, ready for a nice re assembling-cant wait for that time to come
and also all the fixtures and fittings waiting new, so no rusty nuts or bolts go back on.. some i need to get from bmw, but is there anywhere you can get big selection type boxes of stainless nuts bolts and screws or anything like that ? , when you look at them all in plastic chinese takeaway boxes...theres shed loads ive got and i dont want to put any back on the car like that
also dont suppose anyones gone through a similar process and got a big bmw parts number list of nuts/fittings required for a tech 1 car ? although a comming job is to pad and paper and real oem mission...
so now.. i have pretty much aquired all the parts and morsels i need, and have all sorts of boxes of fittings, so many nuts and bolts, things like head light units need refurbing, powder coating the plates and a few other parts, and new fittings etc, and then a case of cleaning and refurbing and wrapping/boxing up every part from the car along with a nice clear out of the garage and new shelving and storage ideas, so when the car comes back....i aim to haver a 100% clean and tidy garage with all the parts clean wrapped and ready to put on like new carefully and orderly boxed and stored in some sort of order, ready for a nice re assembling-cant wait for that time to come
and also all the fixtures and fittings waiting new, so no rusty nuts or bolts go back on.. some i need to get from bmw, but is there anywhere you can get big selection type boxes of stainless nuts bolts and screws or anything like that ? , when you look at them all in plastic chinese takeaway boxes...theres shed loads ive got and i dont want to put any back on the car like that
also dont suppose anyones gone through a similar process and got a big bmw parts number list of nuts/fittings required for a tech 1 car ? although a comming job is to pad and paper and real oem mission...
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
-
spook
- League two here we come !!!
- Posts: 7583
- Joined: Sat Aug 19, 2006 11:00 pm
- Location: portsmouth
I just cleared out my garage, it all went up the tip.
One more to do
One more to do

-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
thanks jim, but its not suspension/running gear parts, thats all very nice still and previous owner overhauled and refurbed all that sort of thing thank god
its more everything else, all interior and exterior nuts and bolts and fittings for everything , not underside
its more everything else, all interior and exterior nuts and bolts and fittings for everything , not underside
-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
spook wrote:I just cleared out my garage, it ALL went up the tip.
One more to do

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
spook
- League two here we come !!!
- Posts: 7583
- Joined: Sat Aug 19, 2006 11:00 pm
- Location: portsmouth
It is nice, its all the spare parts i cant be arsed with.

-
jimbom30cab
- Tech 1 freak
- Posts: 7631
- Joined: Mon Oct 12, 2009 11:00 pm
- Location: in the garage
i did this Carl and spent hours on real oem making parts lists to order through BMW. You could refub many of the fittings, wire brush and hammerite should protect them ok.
-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
next garage open day spook?
Carl, you could do what jim says, wire brush and rust-killer and keep original
received your msg Jim, Thursday evening is fine with me
Carl, you could do what jim says, wire brush and rust-killer and keep original
received your msg Jim, Thursday evening is fine with me

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
Its all about the FERTAN ! 
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
Can you post up what ever list of parts you compile, like in the wiki link only for the interior? It would be greatly appreciated 
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
Only way to do it is sit on RealOEM for hours, it's easy enough to workout what you need.
-
cecotto479
- Caution Unreliable Seller

- Posts: 2949
- Joined: Sun May 13, 2007 11:00 pm
- Location: On a golf course somewhere probably
Namric for fixings or your local engineering shop will have a fasteners supplier.
1981 E23 735i
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
-
jimbom30cab
- Tech 1 freak
- Posts: 7631
- Joined: Mon Oct 12, 2009 11:00 pm
- Location: in the garage
thanks Adit, i'll pop round after work on thursday - should be about 17:30 if that is ok, could you pm me your address again - sorry. thanks
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
What exactly are we referring to? Every clip, nut, bolt and plastic sleeve that's used on the outer bodywork of the car? Or every piece of trim, including gutter covers and chromework?
Do you want part numbers for the rubber cover around the fuel pipe, and the battery bracket too?
Do you want part numbers for the rubber cover around the fuel pipe, and the battery bracket too?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Set up an electrolysis tank to completely remove rust from any parts small enough to go into it.adit wrote:next garage open day spook?![]()
Carl, you could do what jim says, wire brush and rust-killer and keep original![]()
received your msg Jim, Thursday evening is fine with me
Plastic tank, sodium carbonate (washing soda), bits of scrap iron/steel (NOT stainless), and a DC power supply (battery charger at a push).
-
BATTS91
- E30 Zone Squatter

- Posts: 1764
- Joined: Sat May 01, 2010 11:00 pm
- Location: clacton on sea essex
any more on an electrolysis tank ? that sounds interesting to make presume you just put sodium in steel and add water ? +electricity ?
edit : any specific measurments of soda to water or how much metal to put in , this would would good for calipers n lil bits ect ?
edit : any specific measurments of soda to water or how much metal to put in , this would would good for calipers n lil bits ect ?
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
Yes mate pleaseGrrrmachine wrote:What exactly are we referring to? Every clip, nut, bolt and plastic sleeve that's used on the outer bodywork of the car? Or every piece of trim, including gutter covers and chromework?
Do you want part numbers for the rubber cover around the fuel pipe, and the battery bracket too?
Basicly..apart from underside and wheels etc,every part has been stripped inside and out,most interior bolts n nuts are ok/nice, but external/bolt on to shell fittings n screws,nuts,etc are rusting as t,hey do, so want to put all new
Il compile on real oem a list, but for general screws n washers are bmw stainless ? or should i source from elsewhere ?
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
That's a tall order
If anyone's done it, for example in Excel, then I can dump it into the Wiki in due course but I don't have anywhere near enough time to trawl through RealOEM and effectively type it out all over again.
If anyone's done it, for example in Excel, then I can dump it into the Wiki in due course but I don't have anywhere near enough time to trawl through RealOEM and effectively type it out all over again.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
they are mainly Passivated apart from some new stock,polsta wrote:for general screws n washers are bmw stainless ? or should i source from elsewhere ?
it's easy just go through real OEM grab the part numbers and order, it's not that expensive either compared to the time spent looking for the correct sizes/threads from elsewhere,
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
What does passivated mean ?
Gr- a tall order ,but the car is having a top top paint job,and parts n morsel wise everything is splendid,i dont want to put any rusty fittings back on,the car will be one of the best
Gr- a tall order ,but the car is having a top top paint job,and parts n morsel wise everything is splendid,i dont want to put any rusty fittings back on,the car will be one of the best
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
I went to a nut and bolt shop with all the nut's bolts labeled with size and quantity on them. Pretty much all thats in the wiki and it set me back about 30euro's.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I have a stock of hex headed stainless steel self tappers, with 8mm and 10mm heads, with matching 20mm diameter washers, that I use to replace all the screws holding the arch liners, etc. They aren't cheap at about 20p each, but well worth doing.
-
Duke137
- Married to the E30 Zone

- Posts: 7207
- Joined: Sat Aug 29, 2009 11:00 pm
pacerpete wrote:Its all about the FERTAN !
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
me toodiable wrote:Where did you get these from as I could do with replacing mine.Brianmoooore wrote:I have a stock of hex headed stainless steel self tappers, with 8mm and 10mm heads, with matching 20mm diameter washers, that I use to replace all the screws holding the arch liners, etc. They aren't cheap at about 20p each, but well worth doing.
what about the bolts that fix/hold the bumper sections together ? and the ones that hold the kit on,and attach it ?
a mate recomended this place which is local,so im going to pop in there with a few boxes and see what he can match up in stainless
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Use washing soda at a concentration of about one table spoon full to one gallon of water. The concentration isn't at all critical, and doesn't get 'used up' with the process. The solution does get full of orange sludge though, so needs renewing from time to time.BATTS91 wrote:any more on an electrolysis tank ? that sounds interesting to make presume you just put sodium in steel and add water ? +electricity ?
edit : any specific measurments of soda to water or how much metal to put in , this would would good for calipers n lil bits ect ?
The de rusting process takes place most effectively on whichever part of whatever you are derusting is nearest the iron or steel anode, so you ideally need several pieces of scrap iron to serve as anodes around the edges of the tank.
Just take any pieces of scrap iron or steel, clean off an area so that a crocodile clip can make electrical contact, and place them around the sides of your tank, make sure that the crocodile clip and wire is above the level of the solution, and take all the wires back to the positive terminal of your power supply.
Stainless steel will work as an anode, but apparently releases toxic chromium salts into the solution, so shouldn't be used.
Clean off a small area of the part to be derusted, so that a crocodile clip can make contact, then totally immerse the part in the tank. Doesn't matter if the crocodile clip and wire is submerged. Take the wire to the negative terminal of your power supply.
I use an adjustable 0 - 30 volt 2.5A maximum bench power supply, but a basic battery charger can be used, with a high wattage 12 volt bulb connected in series to limit the current if needed.
I find that it can take anything between about 5 volts and the full 30 volts to get a current of about 2A flowing.
The soda solution is non toxic and non corroding to other metals, and no harm is done by leaving the object in longer than needed.
A day in the tank will clean up the most heavily scaled brake calliper or differential, leaving them ready for painting.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The labels on my boxes of screws say "Stainless hex head s/tapping screws A2 10 X 5/8" and "stainless etc. 14 X 3/4" and came from here: http://www.taylorfasteners.co.uk/
I bought a part box of the smaller ones a couple of weeks ago, and they said that it wasn't a stock item, but could get them in if I needed more.
I bought a part box of the smaller ones a couple of weeks ago, and they said that it wasn't a stock item, but could get them in if I needed more.
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
Very interesting reading that Brian. Judging by the last sentence you don't need to remove the worst of the rust prior to starting the electrolysis!?Brianmoooore wrote:Use washing soda at a concentration of about one table spoon full to one gallon of water. The concentration isn't at all critical, and doesn't get 'used up' with the process. The solution does get full of orange sludge though, so needs renewing from time to time.BATTS91 wrote:any more on an electrolysis tank ? that sounds interesting to make presume you just put sodium in steel and add water ? +electricity ?
edit : any specific measurments of soda to water or how much metal to put in , this would would good for calipers n lil bits ect ?
The de rusting process takes place most effectively on whichever part of whatever you are derusting is nearest the iron or steel anode, so you ideally need several pieces of scrap iron to serve as anodes around the edges of the tank.
Just take any pieces of scrap iron or steel, clean off an area so that a crocodile clip can make electrical contact, and place them around the sides of your tank, make sure that the crocodile clip and wire is above the level of the solution, and take all the wires back to the positive terminal of your power supply.
Stainless steel will work as an anode, but apparently releases toxic chromium salts into the solution, so shouldn't be used.
Clean off a small area of the part to be derusted, so that a crocodile clip can make contact, then totally immerse the part in the tank. Doesn't matter if the crocodile clip and wire is submerged. Take the wire to the negative terminal of your power supply.
I use an adjustable 0 - 30 volt 2.5A maximum bench power supply, but a basic battery charger can be used, with a high wattage 12 volt bulb connected in series to limit the current if needed.
I find that it can take anything between about 5 volts and the full 30 volts to get a current of about 2A flowing.
The soda solution is non toxic and non corroding to other metals, and no harm is done by leaving the object in longer than needed.
A day in the tank will clean up the most heavily scaled brake calliper or differential, leaving them ready for painting.
Be perfect prep to then get them zinc plated.
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
There's a place near me who do that electrolysis to bare shells.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
Gavla
- E30 Zone Squatter

- Posts: 1586
- Joined: Tue Dec 06, 2011 11:00 pm
Namrick.co.uk
Worth a look?
Worth a look?


