318 is engine mounts
Moderator: martauto
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Guys I want to change the engine mounts in my car as they look quite tired, firstly are all the mounts the same across the e30 models? And then is this doable at home I've got an idea how to change the mount, undo bottom bolt from subframe and then top, raise the engine with a jack until the arm lifts off the mount and then slide the mount out and fit the new one, will I be able to jack the engine enough to remove the mount?
-
MrWhite
- E30 Zone Regular

- Posts: 721
- Joined: Fri Mar 14, 2008 11:00 pm
- Location: Renfrewshire
Engine mounts are different across the E30 range, depending on engine. M42 uses its own type, quite pricey new if I recall but I think you can fit cheaper solid mounts from another engine type. Somebody else can confirm what ones.
Swapping them is fairly straight forward, as you've outlined. Just be careful how you jack the engine up. You don't want to damage either part of the sump.
Swapping them is fairly straight forward, as you've outlined. Just be careful how you jack the engine up. You don't want to damage either part of the sump.
rust never sleeps
-
age
- Formerly twist316
- Posts: 448
- Joined: Sun Dec 28, 2008 11:00 pm
- Location: cork ireland (kosice slovakia)
e28 m5 mounts are what you want foe your iS. available from ecp iirc
-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
if the engine arm won't clear the mount bolt,remove the engine arm 

m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
With typical attention to detail, as you would expect from this marque, BMW have shaped the holes in the engine mounts to allow the rubber mount to swing inwards as soon as the bottom stud clears the subframe.Emm3 wrote:, will I be able to jack the engine enough to remove the mount?
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Many thanks, which ones would be best to go for original or e28 m5?
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
e28 m5 have different dimensions (taller or shorter iirc)
Just go for original m42 e30 318is ones, they are quite expensive though.
Just go for original m42 e30 318is ones, they are quite expensive though.
-
age
- Formerly twist316
- Posts: 448
- Joined: Sun Dec 28, 2008 11:00 pm
- Location: cork ireland (kosice slovakia)
e28 m5 ones are stronger, offer better sump clearance, and are cheaper ;)
the choice is obvious really
the choice is obvious really
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
True. However, as the m42 doesn't have the two hydraulic shock absorbers going from the subframe to engine mounting arm, the m42 mounts are filled with a hydraulic fluid.age wrote:e28 m5 ones are stronger, offer better sump clearance, and are cheaper ;)
the choice is obvious really
Therefore, noise, vibrations and harshness are severely compromised if using the e28 m5 engine mounts. However, the people who want better sump clearance and cheaper mounts probably don't care about NVH or handling of the car. Solid mounts ruin a road car.
-
jonesy318
- E30 Zone Newbie

- Posts: 212
- Joined: Thu Dec 24, 2009 11:00 pm
- Location: Peterborough..
sorry to hi-jack this thread but i'm currently putting an m42 in place of the original m40 but the m42 didnt come with any mounts on it at all, can i use the m40 arms and mounts??
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Don't use the m40 mounts.jonesy318 wrote:sorry to hi-jack this thread but i'm currently putting an m42 in place of the original m40 but the m42 didnt come with any mounts on it at all, can i use the m40 arms and mounts??
You need the m42 mounts
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Gsf quoted £6 each? And I did check if the same part number covered all models and was told is ones are specificredcar wrote:e28 m5 have different dimensions (taller or shorter iirc)
Just go for original m42 e30 318is ones, they are quite expensive though.
-
jonesy318
- E30 Zone Newbie

- Posts: 212
- Joined: Thu Dec 24, 2009 11:00 pm
- Location: Peterborough..
bugger, best start looking for some then, cheers for advice
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Hi, sorry i'm not too sure what you mean.Emm3 wrote:Gsf quoted £6 each? And I did check if the same part number covered all models and was told is ones are specificredcar wrote:e28 m5 have different dimensions (taller or shorter iirc)
Just go for original m42 e30 318is ones, they are quite expensive though.
Do you mean the m42 ones are £6 each? And yes, the e30 318i iS ones are specific and unique to the e30 318is ONLY.
-
age
- Formerly twist316
- Posts: 448
- Joined: Sun Dec 28, 2008 11:00 pm
- Location: cork ireland (kosice slovakia)
if by "people" you are refering to me, then you can take a walk.redcar wrote:True. However, as the m42 doesn't have the two hydraulic shock absorbers going from the subframe to engine mounting arm, the m42 mounts are filled with a hydraulic fluid.age wrote:e28 m5 ones are stronger, offer better sump clearance, and are cheaper ;)
the choice is obvious really
Therefore, noise, vibrations and harshness are severely compromised if using the e28 m5 engine mounts. However, the people who want better sump clearance and cheaper mounts probably don't care about NVH or handling of the car. Solid mounts ruin a road car.Unless you have a silky smooth 6 pot
can you tell me why guys using m5x engines and anyone who likes to drive on an iS is using the m5 mounts??
typical answer from a guy driving a six pot
-
age
- Formerly twist316
- Posts: 448
- Joined: Sun Dec 28, 2008 11:00 pm
- Location: cork ireland (kosice slovakia)
p.s the iS should have hydraulic shock absorbers on the engine, your problem if your's doesnt :winkeye:
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Because they're cheaper?
My car is an iS. I want an m52 though.
M42 doesn't have shock absorbers.
-
age
- Formerly twist316
- Posts: 448
- Joined: Sun Dec 28, 2008 11:00 pm
- Location: cork ireland (kosice slovakia)
mine does, but i wont argue as its my only one, the rest are m40's 
-
Emm3
- E30 Zone Regular

- Posts: 866
- Joined: Sat Apr 08, 2006 11:00 pm
Do you mean the m42 ones are £6 each? And yes, the e30 318i iS ones are specific and unique to the e30 318is ONLY.
According to Gsf £6 each
According to Gsf £6 each
-
Dave_M3
- E30 Zone Addict

- Posts: 3428
- Joined: Sat Jun 24, 2006 11:00 pm
- Location: Cork
In all fairness, you couldn't really call E28 M5 mounts solid
They are perfect for an M42.
It's a shitty little 4 pot anyway that you need to rag to get anywhere. If your worried about a refined drive and nice and smooth without any vibrations or anything, go buy a golf or something.
I can guarantee most people wouldn't be able to tell the difference between E28 mounts and original M42 mounts anyway if they drove the same car with each and wasn't told which mounts were in it.
They are perfect for an M42.
It's a shitty little 4 pot anyway that you need to rag to get anywhere. If your worried about a refined drive and nice and smooth without any vibrations or anything, go buy a golf or something.
I can guarantee most people wouldn't be able to tell the difference between E28 mounts and original M42 mounts anyway if they drove the same car with each and wasn't told which mounts were in it.
M42 rightness above 6500rpm, nobody can hear you scream
