floor pan
Moderator: martauto
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
Hi, my e30 325i has a large amount of water on the passenger footwell.
Where do you think it is coming from?
Thank you.
Where do you think it is coming from?
Thank you.
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
That's the lake of tears it generates every time it loses a race to a Subaru
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
There is a large rubber grommet behind/underneath the glove box, with wiring looms passing through it into the engine compartment. Check that this is in place properly, the condition of the metal surrounding it, and the condition of the two 6mm studs on the bulkhead that the glovebox hinge bolts to.
If everything here is OK, pull back the carpet, and prod at anything that looks remotely orange with a pointed object.
If everything here is OK, pull back the carpet, and prod at anything that looks remotely orange with a pointed object.
-
e30den
- E30 Zone Regular

- Posts: 502
- Joined: Fri Jul 27, 2007 11:00 pm
- Location: East Kent
It is either rain water or a leak from the heater matrix [ check header tank ]Maltit wrote:Hi, my e30 325i has a large amount of water on the passenger footwell.
Where do you think it is coming from?
Thank you.
-
unmol
- E30 Zone Newbie

- Posts: 170
- Joined: Wed Sep 16, 2009 11:00 pm
- Location: West London, Southall
This happened to mine. But to weld this you have to remove the loom.Brianmoooore wrote:There is a large rubber grommet behind/underneath the glove box, with wiring looms passing through it into the engine compartment. Check that this is in place properly, the condition of the metal surrounding it, and the condition of the two 6mm studs on the bulkhead that the glovebox hinge bolts to.
If everything here is OK, pull back the carpet, and prod at anything that looks remotely orange with a pointed object.
-
nickso
- E30 Zone Addict

- Posts: 4396
- Joined: Sat Jul 23, 2005 11:00 pm
- Location: Go do that voodoo that you do so welllllllll!!
No you don't.unmol wrote:This happened to mine. But to weld this you have to remove the loom.Brianmoooore wrote:There is a large rubber grommet behind/underneath the glove box, with wiring looms passing through it into the engine compartment. Check that this is in place properly, the condition of the metal surrounding it, and the condition of the two 6mm studs on the bulkhead that the glovebox hinge bolts to.
If everything here is OK, pull back the carpet, and prod at anything that looks remotely orange with a pointed object.

'88 e30 328i M52 track bint.
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
Shall i put metal filler on it, and sell it? a’ª
-
penton08
- E30 Zone Camper

- Posts: 1206
- Joined: Sat May 10, 2008 11:00 pm
p40 is much easier to use.Maltit wrote:Shall i put metal filler on it, and sell it? a’ª
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
penton08 wrote:p40 is much easier to use.Maltit wrote:Shall i put metal filler on it, and sell it? a’ª
Decorators Caulk is probably even easier...
Maltit, its your car, fix it how you see fit. It seems you already know what kinda reaction your after
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Do it properly or don't do it at all.Maltit wrote:Shall i put metal filler on it, and sell it?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
Would anyone like to purchase an E30 325i Motorsport? I can assure you it is MINT!
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Minty mint?Maltit wrote:Would anyone like to purchase an E30 325i Motorsport? I can assure you it is MINT!
-
iceox
- E30 Zone Camper

- Posts: 1147
- Joined: Fri May 30, 2008 11:00 pm
- Location: Scottish Borders
what like out the factory mint? get it on swapz bruv, u'll get a 97 plate scooby for it, easyredcar wrote:Minty mint?Maltit wrote:Would anyone like to purchase an E30 325i Motorsport? I can assure you it is MINT!

-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Mint = better condition than it left factory in.iceox wrote:what like out the factory mint? get it on swapz bruv, u'll get a 97 plate scooby for it, easyredcar wrote:Minty mint?Maltit wrote:Would anyone like to purchase an E30 325i Motorsport? I can assure you it is MINT!
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
you can eat your dinner off the floorpan
-
Tom_Maverick
- E30 Zone Camper

- Posts: 1343
- Joined: Wed Aug 25, 2010 11:00 pm
- Location: Brighton
It'd be fortified with iron oxide!
And damp...
And damp...

-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
From birmingham
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Prefer NaCl on my chips not Fe2O3 lolMaltit wrote:you can eat your dinner off the floorpan
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
redcar wrote:Prefer NaCl on my chips not Fe2O3 lolMaltit wrote:you can eat your dinner off the floorpan
You guys are a wierd bunch.
I think you guys need to hit a titty bar and sell your E30's.
-
unmol
- E30 Zone Newbie

- Posts: 170
- Joined: Wed Sep 16, 2009 11:00 pm
- Location: West London, Southall
Oh. I was under the impression that the loom has to be taken out to weld here because the hole that requires welding is the one that passes through the loom into the engine bay.nickso wrote:unmol wrote:This happened to mine. But to weld this you have to remove the loom.Brianmoooore wrote:There is a large rubber grommet behind/underneath the glove box, with wiring looms passing through it into the engine compartment. Check that this is in place properly, the condition of the metal surrounding it, and the condition of the two 6mm studs on the bulkhead that the glovebox hinge bolts to.
If everything here is OK, pull back the carpet, and prod at anything that looks remotely orange with a pointed object.
-
nickso
- E30 Zone Addict

- Posts: 4396
- Joined: Sat Jul 23, 2005 11:00 pm
- Location: Go do that voodoo that you do so welllllllll!!
It can be done without it. I wrapped the loom in a plumbers heat mat.unmol wrote:Oh. I was under the impression that the loom has to be taken out to weld here because the hole that requires welding is the one that passes through the loom into the engine bay.

'88 e30 328i M52 track bint.
-
suchy
- True Zone Relic
- Posts: 6604
- Joined: Tue Apr 26, 2005 11:00 pm
- Location: Portsmouth
What and miss out on all the handbag dramas that unfold here? That would mean leading a normal life....Maltit wrote:redcar wrote:Prefer NaCl on my chips not Fe2O3 lolMaltit wrote:you can eat your dinner off the floorpan
You guys are a wierd bunch.
I think you guys need to hit a titty bar and sell your E30's.
-
kieran325
- Old Skooler

- Posts: 5015
- Joined: Sun Oct 30, 2005 11:00 pm
I'm off to titty bars in Prague this weekend 
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
kieran325 wrote:I'm off to titty bars in Prague this weekend
Don't forget the Instamatic !
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
kieran325 wrote:Will Polaroids do?
Let me ask Barry
-
kieran325
- Old Skooler

- Posts: 5015
- Joined: Sun Oct 30, 2005 11:00 pm
I can't wait 29 days
I'm off in 4 days.
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
Who actually cares that your going Prague? Do you not have any real friends to talk to?
You guys really do lead very sad lives. I feel sorry for your parents and your e30's.
You guys really do lead very sad lives. I feel sorry for your parents and your e30's.
-
ross_jsy
- Married to the E30 Zone

- Posts: 7307
- Joined: Sun Jul 12, 2009 11:00 pm
- Location: Jersey, C.I.
Jesus, you feel sorry for our parents? You are trolling the internet. Well done son.
And as for feeling sorry for our e30's, wtf does that even mean?
And as for feeling sorry for our e30's, wtf does that even mean?
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
Maltit wrote:Who actually cares that your going Prague? Do you not have any real friends to talk to?
You guys really do lead very sad lives. I feel sorry for your parents and your e30's.
Barebacking in Prague or P40ing your 325 / stickerbombing an impretzel - I know which I would rather be doing
-
318isPMK
- E30 Zone Camper

- Posts: 1499
- Joined: Tue Jan 10, 2012 11:00 pm
-
Maltit
- E30 Zone Newbie

- Posts: 20
- Joined: Fri Jun 15, 2012 11:00 pm
You have got the idea mate, well done.318isPMK wrote:Im beginning to think he's got a point... they are shite arent they... Im going to go set fire to mine immediately
-
Mo13
- E30 Zone Regular

- Posts: 722
- Joined: Tue Apr 03, 2012 11:00 pm
- Location: East London
Guys I have had a look under my carpet and the drivers side is moist with a little rust (now a hole after I poked it) any idea where the water might have came from? also do I need to remove the dash to take the carpet out?
Thanks,
Thanks,
-
cecotto479
- Caution Unreliable Seller

- Posts: 2949
- Joined: Sun May 13, 2007 11:00 pm
- Location: On a golf course somewhere probably
I wonder if Barry has already expressed his opinion on this very thread?kieran325 wrote:I can't wait 29 days 8O I'm off in 4 days.
1981 E23 735i
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
As in Polo mint - with a hole?Maltit wrote:Would anyone like to purchase an E30 325i Motorsport? I can assure you it is MINT!
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421

