sachs thrust bearing...........
Moderator: martauto
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
.......... how much are these and where can i get one?
i have a good sachs clutch to replace the LUK piece of shite my m52 has torn appart but it didnt arrive with a thrust bearing. dont want to re-fit the luk one
t i a
i have a good sachs clutch to replace the LUK piece of shite my m52 has torn appart but it didnt arrive with a thrust bearing. dont want to re-fit the luk one
t i a
A 2 door e30 with 8 cylinders, what could be better

-
Meatballs82
- E30 Zone Camper

- Posts: 1136
- Joined: Tue Jan 11, 2011 11:00 pm
- Location: Northamptonshite
I have Boge available from stock - £20.95 excl vat
Hope this helps!
Hope this helps!

-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
stand up to an m52 and a driver with a heavy foot? 
A 2 door e30 with 8 cylinders, what could be better

-
Meatballs82
- E30 Zone Camper

- Posts: 1136
- Joined: Tue Jan 11, 2011 11:00 pm
- Location: Northamptonshite
Im afraid you'd have to let me know! 

-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
How exactly do you expect him to know that?e30-dk wrote:stand up to an m52 and a driver with a heavy foot?
You are using it on the wrong engine that's got 30-40 bhp more. What parts catalogue would have that sort of info in

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
just re use the old release bearing the new one will be the same. Thats not the part that gets hammered
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
well im sorry for asking a question Dez but these conversions have been around for a bit and it may have been tried and tested! and sachs clutch's are good for up to 300bhp so im told by a few so that has bugger all to do with it
simon - thats a fair point mate. my current thrust bearing isnt really noisey so i suppose i could go with that
simon - thats a fair point mate. my current thrust bearing isnt really noisey so i suppose i could go with that
A 2 door e30 with 8 cylinders, what could be better

-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Settle yourself matey.e30-dk wrote:well im sorry for asking a question Dez but these conversions have been around for a bit and it may have been tried and tested! and sachs clutch's are good for up to 300bhp so im told by a few so that has bugger all to do with it
My point is, asking on here if a part has been tried out and up to task on an M52 converted E30 is one thing. Asking a guy who works for ECP's if a standard M20 clutch part is going to be up to the abuse is madness. Are you going to ask for a lifetime guarantee on a £20 part?
I'm only having a laugh with you BTW. There is no need to be sorry

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
If this is for your M52 set up im sure there's another bearing you can upgrade to so the clutch bite isnt so low, iirc its E21 related.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
not a life time guarantee no dez but a year would be ok haha........ i see your point though.
lee - my clutch point right now is nearly in the rear footwell
. thats how bad its got but i may investigate the e21 bearing for when i rip it out to do the change if anyone else can shed some light on it....?......... 
lee - my clutch point right now is nearly in the rear footwell
A 2 door e30 with 8 cylinders, what could be better

-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
According to realoem most BMW release bearings are the same.
http://www.realoem.com/bmw/partxref.do?part=21517521471
E21 323i isnt listed so it could be that one, iirc the shoulders are higher so it opens the clutch more.
Or you could weld small tabs on your existing one to do the same trick.
http://www.realoem.com/bmw/partxref.do?part=21517521471
E21 323i isnt listed so it could be that one, iirc the shoulders are higher so it opens the clutch more.
Or you could weld small tabs on your existing one to do the same trick.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
i'd like to know who putting 300bhp and what sort of torque through one and its not slipping. I'm converting my e36 to manual and was going this M20 flywheel route but i'm not now. Using a 328 setup
-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
My set up is fine on standard M20 Sachs set up. Not 300bhp though.
It will spin 225,40x16 T1rs in third without any clutch slip.
It will spin 225,40x16 T1rs in third without any clutch slip.

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
So it should be fine with 230-240 bhp then 
A 2 door e30 with 8 cylinders, what could be better

-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
its the torque that causes the slip.
My LUK cluth has had it in the c2 touring 220lbs it copes with fine on the road but the 3 ring trips mean its not even done 40k total miles i reckon. Bite point is at the top now
My LUK cluth has had it in the c2 touring 220lbs it copes with fine on the road but the 3 ring trips mean its not even done 40k total miles i reckon. Bite point is at the top now
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
Imo if you had 400hp running through the clutch it wont make a blind bit of difference to the release bearing as all this is used for is to disengage the clutch, when you floor it with your foot off the clutch all the release bearing is doing is nothing but spining with the revs of the engine.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
fair point that. so on that note i will most prob go with the boge item, im not keen on re-using my luk one tbh
A 2 door e30 with 8 cylinders, what could be better

-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
this was the biggest contributing factor to my clutch getting battered so bad.!

since changing this, the gear changes dont feel like the box is wankered lol but with the rod sticking out like this it obv gave the impression i was riding the clutch. so new slave in and sachs going in should be fine

since changing this, the gear changes dont feel like the box is wankered lol but with the rod sticking out like this it obv gave the impression i was riding the clutch. so new slave in and sachs going in should be fine
A 2 door e30 with 8 cylinders, what could be better

-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
if everything is ok, that rod physically can't get like that when the slave is fitted to the box. That looks like someone pushing the clutch pedal after its been removed from the box. I'm not sure about the LUK hang up on the release bearing you really are wasting money by buying a new one.
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
it may well have pulled out like this when i took it out of the box then. it just didnt look good when i saw it lol. clutch still slips so i am going to go ahead and change it.
so you think re using the luk bearing would be ok?
so you think re using the luk bearing would be ok?
A 2 door e30 with 8 cylinders, what could be better

-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
it will be fine, unless it feels all knarly like the bearings are worn re use it. Its got nothing to do with the clutch slipping thats the clutch disc not being man enough.
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
yeah that sounds about right mate lol. it just cant take the power and my lead foot doesnt help its cause,,, poor clutch disc haha
A 2 door e30 with 8 cylinders, what could be better

-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
Is this the same thing as a release bearing? I've a e21 323 item, it's meant to be stronger
Also cost a good lot more! It's an all metal affair though which the sachs one that came with the clutch isn't.
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
its a different length to the e30 325i one so it pushes the pressure plate a bit further 5mm or so. From what i've read its not really needed the 325i one does the job.
About £70 odd from bmw when i bought one
About £70 odd from bmw when i bought one
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
Sounds about inline with when I got it.
What is the effect of it allowing the clutch fork to push on the pressure plate further? (uncharted territory for me and still learning
)
What is the effect of it allowing the clutch fork to push on the pressure plate further? (uncharted territory for me and still learning
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
Makes the biting point higher up,
Im on a standard M20 set up with my M52 an really its not that bad, you just get used to it.
Im sure it was Danthe who welded little tabs onto the shoulders of a standard bearing to give the same effect as the 323i one.
Im on a standard M20 set up with my M52 an really its not that bad, you just get used to it.
Im sure it was Danthe who welded little tabs onto the shoulders of a standard bearing to give the same effect as the 323i one.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
cant see why i would want the clutch bite to be higher tbh
before the clutch got so bad the bite point was brill and i liked it
before the clutch got so bad the bite point was brill and i liked it
A 2 door e30 with 8 cylinders, what could be better

-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Depends on what box/clutch combo your using
Dan had issues because he was using e90 derv box. He had a low biting point. That's why he spaced the spigot bearing.
I need to use a stopper on my clutch pedal to stop the plunger coming out too much and hitting the cover. Other than that clutch is perfect.
Dan had issues because he was using e90 derv box. He had a low biting point. That's why he spaced the spigot bearing.
I need to use a stopper on my clutch pedal to stop the plunger coming out too much and hitting the cover. Other than that clutch is perfect.

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
Another option is to tack a couple of blows of weld onto the fork where the bearing sits. That way you can use a stock bearing and get any amount of slack you want.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
ive been using an m42 box, e30 slave and m20 thrust bearing and i was entirely happy with the bite ect ect. my clutch point is only through the roof because the clutch is so buggered. i will be using an m20 bearing again for sure as i wouldnt want my bite to be any higher than what it was when healthy.
if that was the case, with how bad it is right now i wouldnt have any clutch at all
if that was the case, with how bad it is right now i wouldnt have any clutch at all
A 2 door e30 with 8 cylinders, what could be better

-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
I have both the 323 one and the one from the new clutch, I don't want the clutch bite to be to high! I'll compare both side by side I think. A mate used the same combo as myself (and what Ant has) I'll ask him what his is like.
-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Ant you don't have to worry. Just put it back as it was with a new slave sorted.

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
i have dez, new slave is in but clutch is fooked. rippin it out next week 
A 2 door e30 with 8 cylinders, what could be better

-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Yeh I meant with a new clutch aswell mate.
No need to worry about which thrust bearing to use or modding one
No need to worry about which thrust bearing to use or modding one

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
ah right yeah i get you mate, will use the same setup as i did before.
for anyone else looking in on this, it was fine
for anyone else looking in on this, it was fine
A 2 door e30 with 8 cylinders, what could be better


