my turbo project - new vids inside !!

[breakermart]

love it, i can tell this is going to look good, you do realise youl get people asking "how much to do me one"? lol

hopefully should look good mate

i aint making non for no one else lol

good lad, tell them now before they get any ideas lol, bet they still ask though haha

[fowler]

ross you have far too much time on your hands bell me if you need some ideas

[ross2009]

lol i know man but its more shits and giggles and aesthetics
but then again when its all fully forged wont hurt by getting more air flow in

[fowler]

the TSD mani is actually very good aprt from about 2200rpm goes a little flat as volometric efficenncy of the M20 is poor then no sure why just is what you need is similar to the E36 or e46 M3 inlet plenums large expansion chamber for induction noise lol
PLus you need to make ikt out of carbon too you free for a chin wag ?

[ross2009]

yeah mate its gonna be sort of similar to the 666fab one but with a larger plenum hopefully yeah mate only watching the footy

gonna be some thing like this

[fowler]

whats there website address again cant remember it

[ross2009]

who 666fab ? lol

[fowler]

just tried site is under construction. yeah them excatly what i thought the design would be you could use a dirty big throttle then as well but you are gonna have to do some serious amount of mappin/dvelopment good luck

[ross2009]

yeah its been under construction for quite a while now
dirty big throttle that almost sounds naughty

yeah they guy that did my mapping is cool hell spend all the time he can to get it right
this is the 666fab one volk makes

[fowler]

i know some where does a 78mm one will try and find the web address

[ross2009]

i was going to go 75 mm ive looked on the summit racing website there shit loads on there

[fowler]

have a look at this one http://www.gb-ent.com/index.php?page=sh ... t&Itemid=1
cheap too

[ross2009]

yeah theres ones like that all over ebay cheaper than that aswell theres ones on ebay that are 115 mm inlet thats over 4 inch inlet lol

[fowler]

far to big lol 80mm will do fine squire

[ross2009]

yeah i know thats just HUGE lol mmmmm 80mm i really want a polished one tho coz im a tart lol not a blue one lol

[ross2009]

holes cut for the bk plate just gotta shape the ends and cut to width

finished article

[ross2009]

a few more its taking shape slowly

[breakermart]

do it do it

[ross2009]

do it do it

lol ha
what ya reckon ??

[breakermart]

yes looks like its going perfectly. just need the welds to be neat and tidy to finish it off nicely. i do like to see some good fabrication. alot of the sh** you can buy off internet can be done so much better by a good fabber and it seems your doing just that mate. DO IT DO IT

[ross2009]

ha got bit more cutting and fabbing to do be for i weld it i want it to fit nicely together first then i can weld it all in one go

[ross2009]

new arps going in too

[kingcruizer]

new arps going in too

hello mate, can i ask where you got your arp's from and how much. I'm looking for a set and will need them soon.

nice project there too, I'm also doing a itb/plenum job for my supercharger and reading this has spurred me back into it.

clive

[ross2009]

yes mate cheers
its a guy i know in america can get them im not going to say on here how much tho ill pm you

over here there 300 quid and there cheaper than that i can tell ya

[Steve]

I'm after a set also mate if you can help me out

[ross2009]

I'm after a set also mate if you can help me out

no worry pm on its way

[fowler]

ross make me a manifold you owe me !!!!!

[ross2009]

ross make me a manifold you owe me !!!!!

your selling your motor why do you want one lol

[fowler]

the daily has been written off due to an old codger so driving the tourer ATM so need some shiney bits so get your finger out and get mine made

[ross2009]

ha I ain't even made mine yet bert ;)

[ross2009]

A little bit more done today

[Rav335uk]

Will the masking tape hold up to the pressure Ross

[ross2009]

Na I'll change it to some duc tape

[fowler]

lol well hurry up then ross

[ross2009]

made the side plates today