Timing marks help please

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
jesmond
E30 Zone Newbie
E30 Zone Newbie
Posts: 107
Joined: Thu May 19, 2005 11:00 pm
Location: Darlington, County Durham

Post Mon Jan 30, 2012 4:52 pm

Hi chaps

I'm trying to do the valve gaps on my E reg Tech 1 325 Sport switchable auto. I've had the top off, found my painted mark on the flywheel, marked up my distributor body with the cylinders, but no marks are on the timing belt covers or anything to mate the flywheel mark up to for TDC. In the absence of this, I've used what I thought to be the correct mark which is effectively the edge of the riveted holder for the timing slug. It seemed to make sense at the time. However, now that I've got it back together and I've driven it, it's awful. Much worse than before. The engine tick over note now seems to sound slightly quicker and 'busier' in the tick type noise these engines make anyway, though the revs seem ok. Also, the gearbox isn't changing up to top gear (4th) properly - it goes in, then immediately changes down to 3rd. This wasn't happening before, oil level is correct etc in the box and in good condition (I know that these auto's can go into 'get you home mode' if the oil level is incorrect/in need of renewal. This isn't that). I'm thinking that I didn't have TDC when aligning the flywheel to my supposed mark. Do you line the flywheel mark to the timing slug or something?
Any advice would be great, thanks guys.

Paul
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Mon Jan 30, 2012 5:03 pm

TDC marks on cam and head , approx 2 O'clock position viewed from the front, line to line

crank TDC mark in front timing ( inner cover) and 2 O'clock is on the innner belt drive pulley, remove mass damper to see it , notch to line if that makes sense

all are really easily seen once the area is cleaned...

why are you using the flywheel(flexplate on autos) for timing BTW ????
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
User avatar
jesmond
E30 Zone Newbie
E30 Zone Newbie
Posts: 107
Joined: Thu May 19, 2005 11:00 pm
Location: Darlington, County Durham

Post Mon Jan 30, 2012 5:17 pm

Ant wrote:TDC marks on cam and head , approx 2 O'clock position viewed from the front, line to line

crank TDC mark in front timing ( inner cover) and 2 O'clock is on the innner belt drive pulley, remove mass damper to see it , notch to line if that makes sense

all are really easily seen once the area is cleaned...

why are you using the flywheel(flexplate on autos) for timing BTW ????
Sorry Ant, you've lost me mate ha ha. I don't know what you're saying. Marks on cam and head? Crank TDC mark in front timing (inner cover)? - I can't see any marks on the covers anywhere. Why are you using the inner belt drive pulley? I think I am using this, but I've just called it the damper. Remove mass damper? Don't know what you mean, I didn't expect to be removing any damper. Last time I saw that come off the timing belt was being renewed!
All I've found is the white painted mark on the 'pulley' with a 't' and 'c' on either side of it (it also has marks like 'Z' on it, and a pair of holes). I assume this painted mark is the main mark. But I just can't see anything to line it up to, and I've cleaned the area's. Please confirm I'm not removing any damper.
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Mon Jan 30, 2012 5:26 pm

Why are you farting about with TDC marks to do the tappets? Just turn the engine over with a 22mm spanner until the lobe you're doing is 180 degrees away from the rocker, check the clearance and adjust if required.
User avatar
jesmond
E30 Zone Newbie
E30 Zone Newbie
Posts: 107
Joined: Thu May 19, 2005 11:00 pm
Location: Darlington, County Durham

Post Mon Jan 30, 2012 5:29 pm

Blimey mate, now I am really lost!
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Mon Jan 30, 2012 5:34 pm

Don't think it can be explained any simpler than Andys explanation. TDC is of no relevance to what you are trying to do.

Here's what a quick Google returned though;
http://www.pelicanparts.com/bmw/techart ... Adjust.htm
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
mrb27
E30 Zone Regular
E30 Zone Regular
Posts: 345
Joined: Wed Nov 17, 2010 11:00 pm
Location: Essex

Post Mon Jan 30, 2012 5:41 pm

to check/adjust valve clearance, timing has nothing to do with it m8. all you have to do is turn the crank with a 22mm spanner as said above and check/adjust the tappets as the cam lobe is furthest away from contact. it should be a 20 min job at most. engine should be stone cold at the time.

so have you lost your timing on the engine? i.e removed the belt from the cam etc?
Image

Uploaded with ImageShack.us
User avatar
jesmond
E30 Zone Newbie
E30 Zone Newbie
Posts: 107
Joined: Thu May 19, 2005 11:00 pm
Location: Darlington, County Durham

Post Mon Jan 30, 2012 5:54 pm

Oh no, nothing like that. It's just that everything I've read so far on how to do the valves states you should use the firing order, get TDC for each cylinder. That's what I've done, trying to line up the marks, do number 1, then turn the engine to number 5 etc, but I've got myself confused with the lack of a mark and obviously have norsed it up. The Pelican advice and you guys seem to suggest firing order isn't necessary, which is confusing. All I need to do is redo properly.

Have to go off line now, but thanks for your help.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Jan 30, 2012 7:23 pm

It helps if you know the firing order, since this tells you which valves are going to open next, and you can be looking in the right place, buts it's by no means essential. Tappets can be adjusted in any order you like, as long as you adhere to the "rule of 7" - if the valves of cylinder 2 are open, then adjust the tappets of #5, if the valves of #4 are open, then adjust #3, and so on.