Heater troubles-> fixed but I have a doubt....

Need technical Q/A then you're in the right place

Moderator: martauto

clipper
E30 Zone Squatter
E30 Zone Squatter
Posts: 1980
Joined: Mon Aug 22, 2005 11:00 pm
Location: Madrid

Post Fri Jan 27, 2012 7:24 am

I'm sure that my heating isn't as good as it used to be. but I'm puzzled as to what can go wrong on such a simple system....

The heaters do put out warm air (but not "hot") so the valve to the matrix must be operating at least partially, but what else could restrict the flow of hot water through the matrix? (the matrix has been flushed through several times since the car was "recued" and since then I have kept the cooling system spotlessly clean)

I am assuming that my prefacelift car uses the electrically operated valve, is this right?

The only other thing "wrong" is that there is quite a lot of free slack in the temperature wheel (play in the cable), but as far as I know this cable only varies the flaps in the box to channel hot / cold air, and no real "cold" air is noticed so I don't think its that...

I'm using mt car to go to work in sub zero tmperatures so I want to have a look at this over the weekend, any ideas?
Last edited by clipper on Sun Jan 29, 2012 8:26 pm, edited 1 time in total.
These are sensations as hard to forget as they are to ignore.....
User avatar
blingsta
Boost Junkie
Posts: 2930
Joined: Fri Jan 27, 2006 11:00 pm
Location: Enfield

Post Fri Jan 27, 2012 10:52 pm

i posted the same topic last week mate.. im in the same boat.. low water pressure was mentioned by mr mooore, ie the water pump no good, but ive only just changed it and changed the radiator too...

my next step is to change the matrix and see what happens
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 27, 2012 11:30 pm

The temperature of the air from the heater is controlled totally by the flap on the end of the bowden cable that runs from the temp. knob. The electrics associated with the knob are solely to ensure that the heater is completely off when the knob is at full cold.
If there's free play in the cable, then that could well be your problem.
clipper
E30 Zone Squatter
E30 Zone Squatter
Posts: 1980
Joined: Mon Aug 22, 2005 11:00 pm
Location: Madrid

Post Sat Jan 28, 2012 12:50 am

Ok, I'm 99% certain that I have no problem with my cooling system in general (it's all less than two years old and the car has no problem maintaining a constant working temperature).

So I'll have to see why there's so much slack in the temp knob cable.

Thanks.
These are sensations as hard to forget as they are to ignore.....
e301988325i
E30 Zone Addict
E30 Zone Addict
Posts: 3701
Joined: Fri Feb 01, 2008 11:00 pm
Location: Taunton, Somerset

Post Sat Jan 28, 2012 12:13 pm

IIRC if the two hoses that feed the matrix on the bulkhead are fitted the wrong way around then problems occur
I said:

Can anyone suggest how to test if the boot lights are staying on with the boot shut?

e30topless said:

lock the wife in there
clipper
E30 Zone Squatter
E30 Zone Squatter
Posts: 1980
Joined: Mon Aug 22, 2005 11:00 pm
Location: Madrid

Post Sun Jan 29, 2012 8:39 pm

So today I spent a good few hours in awkward positions in the footwells trying to sort out the bowden cables... what a nightmare. I got stuck upside down at one point when cramp set in...

Anyway I adjusted all the slider cables to the best of my ability (the footwall vest closes better now)

But when I set about doing the temp wheel cable the slack wasn't really the issue.

At the opposite end to the wheel there is a simple lever which operates a flap in the heater box, but (assumingly related to my dealer aircon), this lever has been extended with a longer metal overlay from which a rod operates another lever on what looks like a rheostat in a metal box (has two wires coming off it).

The ratio of the two levers and the movement in the shafts that they operate is not matched perfectly, so the rheostat was reaching the end of its travel before the flap in the heater box was getting fully opened (turning knob to hot).

I adjusted everything as best as I could but I had to sacrifice a bit of movement in the rheostat in order to get full heating.

It has worked for the heating ( I now have full heat and even heat from the dash vents which I didn't have before), but what about this rheostat?

I can't see why a basic dealer aircon needs to know at what position the temp knob is at, a switch to detect fully cold I could understand.

Anyone any ideas about this?
These are sensations as hard to forget as they are to ignore.....
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 29, 2012 9:35 pm

You're into unknown territory for me now, with dealer fitted aircon, but I can't see any reason for an added switch to detect that the heater's set to cold, since there's already one on the temp knob that could be used.
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Sun Jan 29, 2012 9:40 pm

Brianmoooore wrote:You're into unknown territory for me now,
Holy Bejesus Batman !!!!!


I thought i would never here those words from you Brian !
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
clipper
E30 Zone Squatter
E30 Zone Squatter
Posts: 1980
Joined: Mon Aug 22, 2005 11:00 pm
Location: Madrid

Post Mon Jan 30, 2012 10:27 am

kam-325i wrote:
Brianmoooore wrote:You're into unknown territory for me now,
Holy Bejesus Batman !!!!!


I thought i would never here those words from you Brian !
Brian only gets involved with genuine BMW goods, none of this aftermarket Spanish/Italian rubbish !

Still, surely someone with A/C knowledge might know what this component is and what I may have done by sacrificing part of it's operation...
These are sensations as hard to forget as they are to ignore.....