Throttle Help

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
GreatOldOne
E30 Zone Newbie
E30 Zone Newbie
Posts: 111
Joined: Thu Sep 08, 2005 11:00 pm
Location: Northants, UK

Post Thu Jan 26, 2012 8:56 pm

Hi chaps, I wonder if you could help me out.

Could you tell me what these screws do, and how they effect engine performance / fuel mix / whatever?

On top of the throttle:

Image

On the AFM:

Image

I'm trying to find out if my idle speed is too high. It's currently around 1000rpm at cold. Is this OK? And if not would these screws affect idle speed?

I know that vacuum leaks can cause idle issues, but I've checked all the hose junctions are tight, and all the hoses are brand new.

Cheers

Jason
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Thu Jan 26, 2012 9:22 pm

What engine ?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Thu Jan 26, 2012 9:40 pm

DON'T TOUCH THE AFM SCREW!

No if's, no but's, just leave it alone. If you've already fiddled with it, you'll have to connect the car up to a gas analyser to put it back where it should be.

As for the high idle, 1000 isn't too bad, but idle speed is electronically controlled, not mechanically. Air leaks, rich running and a non-functioning TPS can all contribute to high, lumpy or rough idle.

Learn more about Idling in the Wiki:

http://www.e30zone.net/e30zonewiki/inde ... ake#Idling
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Thu Jan 26, 2012 9:43 pm

Dont touch the the screw on the on the throttle body either as this affects the throttle position sensor.

Have a good read through the wiki as detailed above.

GrrrMachine, its worth noting that the screw pictured on the AFM is only for minor adjustment of the mixture. The main one is under the big black cap, this is the one that causes the biggest change in mixture.

I only had that confirmed a few weeks back on another similar thread.
User avatar
GreatOldOne
E30 Zone Newbie
E30 Zone Newbie
Posts: 111
Joined: Thu Sep 08, 2005 11:00 pm
Location: Northants, UK

Post Thu Jan 26, 2012 10:29 pm

Thanks for your help.

For clarity, it's an M20B25, Early 86 model.

I don't know if the AFM screw has been messed around with, as it came as is - the engine is no longer in an e30, but in my Marlin Sportster.

www.greatoldone.co.uk

If 1000rpm tick over is OK, I'll leave them well alone. I just thought it was high, as it makes no mention of the correct speed in the Bentley manual (or at least I haven't found one)

Ta

Jason
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Fri Jan 27, 2012 10:34 am

Mine runs at 1000RPPM when cold and 750 when warm which from what I am told is about right.
e301988325i
E30 Zone Addict
E30 Zone Addict
Posts: 3701
Joined: Fri Feb 01, 2008 11:00 pm
Location: Taunton, Somerset

Post Sat Jan 28, 2012 4:31 pm

Rtaylor2208 wrote:Dont touch the the screw on the on the throttle body either as this affects the throttle position sensor.
Not so.

The golden, slotted screw pictured controls the air bypass for the butterfly.

In addition to this, although not in shot is another screw which is the butterfly position stop, this affects the butterfly and TPS and should not be adjusted unless either a) it has already been tampered with or b) The butterfly is jamming shut on return.

Ps) It sounds as though your idle speeds are fine, perhaps a smidge high but if it's running ok then I'd advise to leave well alone!
I said:

Can anyone suggest how to test if the boot lights are staying on with the boot shut?

e30topless said:

lock the wife in there