M50 coolant system pressurising

Need technical Q/A then you're in the right place

Moderator: martauto

be11
E30 Zone Newbie
E30 Zone Newbie
Posts: 96
Joined: Sun Jul 04, 2010 11:00 pm

Post Sun Jan 15, 2012 1:37 pm

hi guys.

right, i know this usualy means head gasket failure or cracked head etc, but is there anything else it could be?

I bought the engine out of a running car that id seen around numerous times running sweet (e34 525). Did the engine conversion to my e30 and had a few problems getting the cooling system bled properly. after numerous attempts and a few hot encounters, the temperature now sits perfectly and it seems to be working fine.

But now after a short drive all my coolant hoses are rock hard. Iv tried the kseal trick and doesnt seem to make a difference.

The thing is it doesnt get bad until iv been for a drive in it. when i put the kseal in it i left it idling for about 45 minutes and i thought it had worked, only to go for a drive the next day and find my hoses are rock hard again.

Im pretty sure this means taking the head off to inspect but im just wondering if anyone else might have any advice?

cheers guys. This is really gonna stump me as its my daily hack. :(
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 15, 2012 2:46 pm

What do you mean by 'rock hard'? At a working pressure of 30 PSI they should be hard.
Is it actually losing coolant, leading to overheating?
be11
E30 Zone Newbie
E30 Zone Newbie
Posts: 96
Joined: Sun Jul 04, 2010 11:00 pm

Post Sun Jan 15, 2012 4:37 pm

30psi? Is that really what pressure there work at? The hoses usually are hard enough that you can only compress them a tiny bit. Its not loosing coolant until it pops a hose off which it has done a couple of times.
e30-EVN
Old Skooler
Old Skooler
Posts: 3382
Joined: Sun Dec 13, 2009 11:00 pm
Location: S.Wales

Post Sun Jan 15, 2012 4:58 pm

Popping hoses off or blowing them is NOT a good sign.!!

An old m20 2.5 of mine did this..... It was headgsaket to blame 8O
A 2 door e30 with 8 cylinders, what could be better winkeye :D
be11
E30 Zone Newbie
E30 Zone Newbie
Posts: 96
Joined: Sun Jul 04, 2010 11:00 pm

Post Sun Jan 15, 2012 8:07 pm

I think it may have only popped off hoses that were poorly fitted. Just Been out for a 15 min drive. It got up to temp and I pulled over. The hoses are firm but not rock hard anymore, pretty sure there no more than 25 psi.

Possibly might be ok then? :mad:
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 15, 2012 8:36 pm

be11 wrote:30psi? Is that really what pressure there work at?
http://bmwfans.info/parts/catalog/E34/S ... /radiator/
Item #7
be11
E30 Zone Newbie
E30 Zone Newbie
Posts: 96
Joined: Sun Jul 04, 2010 11:00 pm

Post Sun Jan 15, 2012 9:37 pm

So does that mean the cap releases pressure at 2 bar? Most jap stuff does this but has an overflow tank after the cap?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 15, 2012 9:58 pm

be11 wrote:So does that mean the cap releases pressure at 2 bar?
That's what it should do!
Most standard E30s have 1.4 bar caps, and there was (and still is) a safety recall for these caps around'96/'97. Some of these caps were failing to release at the correct pressure, resulting in the failure of the heater valve on the side of the heater box, and the subsequent scalding of the legs of whoever was in the front left seat. There are still loads or the original caps still in use, and I'm convinced that these are still killing heater valves to this day.
AFAIK, the recall didn't apply to 2.0 bar caps.
be11
E30 Zone Newbie
E30 Zone Newbie
Posts: 96
Joined: Sun Jul 04, 2010 11:00 pm

Post Mon Jan 16, 2012 6:29 pm

Ok so I did 65 miles in the car today, mostly motorway. Temp was fine the whole way. When I got back the hoses were quite firm but still with a tiny bit of give. The rad cap seemed to be trickling a tiny bit of pressure out. But the expansion tank was slightly bulged which is worrying.