How tight should the head bolts be on a M20 engine?
Moderator: martauto
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
never thought of doing it that way, may well be the way forward..........
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
How about your wheel bolts?Tay wrote:you can just look at my cars if you think i'm a bodger!
when you've torqued as many heads down as i have you get to know the feel of how tight things are! your more than welcome to come and check my head bolts if you wish and i can guarentee they are dead on! and 2.5k after rebuild and no issues........
quezzies?!
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
holding the wheels on nicely cheers! 
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
Well funnye30topless wrote:you guys use a torque wrench ? I just wait until my elbow clicks
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Therein lies the problem!e30topless wrote:a no brainer
He probably re-uses oil filters as well...wash them out in paraffin and off they go again. Tighten it on with Mole grips, set the tappets with a McDonalds plastic spoon handle and off it rattles!
-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Where can i look at your cars?Tay wrote:you can just look at my cars if you think i'm a bodger!

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
my sport in photos.............. await the onslaught!!!!
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
I just have......... Who did the retrim, Torvill & Dean?
-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
I've had a little look too. Glad i did as well. That proves without any doubt that your no bodger!

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
Mikey_Boy
- E30 Zone Regular

- Posts: 996
- Joined: Sun Mar 16, 2008 11:00 pm
- Location: Cheshire - trying to avoid the bling!
[/quote]
Therein lies the problem!
He probably re-uses oil filters as well...wash them out in paraffin and off they go again. Tighten it on with Mole grips, set the tappets with a McDonalds plastic spoon handle and off it rattles!
[/quote]
Still laughing at this...........!
I never would have thought M20 head bolts would cause sooooo much debate.
Stick with the manufacturers recommendations - written by engineers for mechanics...
Therein lies the problem!
He probably re-uses oil filters as well...wash them out in paraffin and off they go again. Tighten it on with Mole grips, set the tappets with a McDonalds plastic spoon handle and off it rattles!
Still laughing at this...........!
I never would have thought M20 head bolts would cause sooooo much debate.
Stick with the manufacturers recommendations - written by engineers for mechanics...
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
mcdonalds spoons are a bit on the thick side, i tend to go for one of their chewed down coffe stirers..............
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
I was under the impression that was what you used to make rocker gaskets out of.....Tay wrote:mcdonalds spoons are a bit on the thick side, i tend to go for one of their chewed down coffe stirers..............
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
no. now thats just stupid...............
-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Not compaired to the sh1te you've been posting!Tay wrote:no. now thats just stupid...............

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
now thats just harsh.............
