316 TO 318IS SWAP GOING WRONG :( wire has burnt out on loom
Moderator: martauto
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
hello all . i have just finished swapping my friends 316 carb engine for a 318is engine. i have connected the engine harness to the original fuse box, swiched the ignition on and a whole load of smoke came out the wiring loom. i have pealed back the insulation and one wire a yellow/? has melted and is now undressed it self. this wire on the loom runs from the fuse box wiring connecter to a red wire in the loom. what am i doing wrong ? there is no life in the engine when trying to turn over . nothing is happening. would i need to replace the fuse box? some one please help . MR MOORE WHERE ARE YOU !

-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Pin 20 by any chance on the connection by the fuse box ?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
I think so kam . What am I doing wrong ?
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
I do remember brian mentioning that on some looms, the connection on pin 20 is live, but on socket by the fuse box, pin 20 is earth.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Jimbob
- E30 Zone Addict

- Posts: 3731
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Poole
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Thats the post i was after
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
johnl320
- E30 Zone Addict

- Posts: 3124
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Hampshire
I'm about to break a 318is so if you need another loom or any other bits give me a shout. 
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
John ! Where u been all this time . I was searching hi and low for this engine . Took me 4 month months to find one . How much u want for the loom ? Pm me .
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
Thanks Jimbob
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The damage that occurs to the engine loom is relatively minor and easy to sort, by replacing the whole engine loom, if not by any other way.
Unfortunately, the worst damage occurs to the main body loom, where it goes from the fusebox to the area behind the glovebox.
You need to open up the fusebox and check the remains of the brown wire hasn't melted to anything in there, and get to work with the side cutters, removing as much of this wire as you can, including the section that goes to the engine loom socket.
The red/yellow on the engine loom that has melted can be removed completely. It's not needed for your car.
The total amount of damage done depends on how long you left the ignition on, and there's no guarantee that the damaged body loom wiring won't cause problems in the future. Cars have been written off for much less than this!
Unfortunately, the worst damage occurs to the main body loom, where it goes from the fusebox to the area behind the glovebox.
You need to open up the fusebox and check the remains of the brown wire hasn't melted to anything in there, and get to work with the side cutters, removing as much of this wire as you can, including the section that goes to the engine loom socket.
The red/yellow on the engine loom that has melted can be removed completely. It's not needed for your car.
The total amount of damage done depends on how long you left the ignition on, and there's no guarantee that the damaged body loom wiring won't cause problems in the future. Cars have been written off for much less than this!
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
Ok I will get to work this morning with stripping them wires back . The engine loom had two relays only and missing one is this normal ? Or are they ment to have all three relays ? Thanks Brian .
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Third relay socket is for a lambda sensor in the exhaust, which you don't have.
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
Brian I am at the car , I'm trying to turn it over and noting .
any ideas . I have sniped all the pin 20 wiring out as it as frazzled . Is was only left on for 5 secs so all the other wires are ok back at the glove box .
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Have you opened up the fusebox? The most serious damage can be in here, since the affected wire is much thinner than the burnt one in the engine loom, and will have become considerably hotter.
The damage should still allow the engine to crank, possibly accompanied by smoke. Try linking 11 and 14 in the diagnostic socket, which should crank the engine.
The damage should still allow the engine to crank, possibly accompanied by smoke. Try linking 11 and 14 in the diagnostic socket, which should crank the engine.
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
That worked mr more . It turned over . But without doing that with the key nothing . . I have two wires coming off the steering cloum green/purple and green/brown and also two off the ecu harness purple/ grey and grey/black this both have diffent cennection blocks and don't fit . Has this got someting to do with it ?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
None of those wires are required. They're to do with parking lights, aircon and auto gearboxes.
It's a black wire out of the ignition switch, that becomes black/yellow half way down the steering column, that controls the starter motor.
May have an immobiliser connected in line with it.
It's a black wire out of the ignition switch, that becomes black/yellow half way down the steering column, that controls the starter motor.
May have an immobiliser connected in line with it.
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
There is no imobiliser on it Brian , I don't have many relays in the in the fusebox , will take a pic , And upload
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
http://i1213.photobucket.com/albums/cc4 ... 9c8b3a.jpgBrianmoooore wrote:None of those wires are required. They're to do with parking lights, aircon and auto gearboxes.
It's a black wire out of the ignition switch, that becomes black/yellow half way down the steering column, that controls the starter motor.
May have an immobiliser connected in line with it.
http://i1213.photobucket.com/albums/cc4 ... b7ea46.jpg
http://i1213.photobucket.com/albums/cc4 ... 3137a4.jpg
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
The wiki has all this info, if you look:
http://www.e30zone.net/e30zonewiki/index.php/Fuse_Box
Now you can see what relays you have.
http://www.e30zone.net/e30zonewiki/index.php/Fuse_Box
Now you can see what relays you have.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
While you're at it, sort your fuses out, before you melt some more loom!!Grrrmachine wrote:The wiki has all this info, if you look:
http://www.e30zone.net/e30zonewiki/index.php/Fuse_Box
Now you can see what relays you have.
Especially the fuel pump fuse, #11, which is 4X its correct rating!
-
gafta
- E30 Zone Newbie

- Posts: 132
- Joined: Sat Nov 10, 2007 11:00 pm
All sorted now . What a headache it was as well . Turns out there's some wires behind the glove box u have to switch over for the ignition to work . Took me ages to figure it out after stripping the wiring loom down to check the wires after the burn out . Then there was no spark at all plugs , one of the earth cables that tun along the engine harness to the c101 plug was cut . Once that was connect is sprung to life . I know have no more hair left on my head . Want to thank u mr Moore for your reponses . You are a true gent .
