If there's one thing that you can guarantee to be worn on a relatively low mileage (100k) M20 head, it's the exhaust valve guides!Tay wrote:
guides and seats is the last thing thar i would do, they never get them right and they tend not to be worn,
M20 Head Removal
Moderator: martauto
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
Agree with Brian there inlets guides are normally fine exhaust guide are normally worn
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
again i fitted a head to my own car years ago that was so bent and twisted that there was no way we could have fitted it to a customers car, especially as the cam was like a banana once fitted and would barely turn!!!!! and that was well into the 150k mark and the guides were all fine. and we've again never fitted any.
always worth checking and if they are worn then fair enough, i'm not saying they don't wear just saying why spend if there is no need to???
******please bear in mind what i do with my own cars doesn't reflect on how i work on a customers car********
always worth checking and if they are worn then fair enough, i'm not saying they don't wear just saying why spend if there is no need to???
******please bear in mind what i do with my own cars doesn't reflect on how i work on a customers car********
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
exhaust guides wear, the inlets don't really. They'll do 250k easy the inlets and still be in spec.
I had 6 new exhaust guides fitted recently to an M20 head £160 all in including the price on the guides. which were about £10 each
The rockershafts are totally seperate to the head bolts - your thinking of an M30 on that.
I had 6 new exhaust guides fitted recently to an M20 head £160 all in including the price on the guides. which were about £10 each
The rockershafts are totally seperate to the head bolts - your thinking of an M30 on that.
-
Tedswagon
- E30 Zone Addict

- Posts: 2195
- Joined: Sun Nov 23, 2008 11:00 pm
- Location: Edinburgh
There is loads of info for each of these jobs in the wiki links above. With this reference info you should be fine. If you did get stuck you are only a q and a in technical section from getting going again.
http://www.e30zone.net/e30zonewiki/inde ... ket_Change
http://www.e30zone.net/e30zonewiki/inde ... ket_Change
E30 316i auto coupe build thread here viewtopic.php?f=25&t=273035
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
I would NEVER use stretch bolts again.
Rob. OEM head gasket set, a set of stretch bolts, a face off to get the right finish to the head, replace the stem seals, lap in the valves and the jobs a goodun. That will see the job done in a good manner, using quality parts and as cheap as you can.
Si's right with the manifold though. Have that checked before you refit. And the reason to have the head faced (not skimmed, facing is a miniscule amount) is that you'll have a perfect finish to mate the gasket to.
Yes you will find some cam wear and exhaust valve guide wear but if it aint noisy at the moment, it won't be noisy on reassembly (as long as the order is kept right). Yes it's a bit of a lottery on how long before it does get noisy but thats the risk you take. Any very worn rockers I would replace though. Using Febi brand is the same as OEM.
Rob. OEM head gasket set, a set of stretch bolts, a face off to get the right finish to the head, replace the stem seals, lap in the valves and the jobs a goodun. That will see the job done in a good manner, using quality parts and as cheap as you can.
Si's right with the manifold though. Have that checked before you refit. And the reason to have the head faced (not skimmed, facing is a miniscule amount) is that you'll have a perfect finish to mate the gasket to.
Yes you will find some cam wear and exhaust valve guide wear but if it aint noisy at the moment, it won't be noisy on reassembly (as long as the order is kept right). Yes it's a bit of a lottery on how long before it does get noisy but thats the risk you take. Any very worn rockers I would replace though. Using Febi brand is the same as OEM.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
OK having read the Wiki articles I think I'm gonna have a crack at doing a proper job on this.
First thing to do is get the head off and see exactly what I'm dealing with.
The cars done 143k so I guess its due a sympathetic head rebuild anyways.
I guess if I can get it stripped down to a bare head as per the Wiki guide a machine shop will be able to tell me if the guides are worn and need replacement - it will need to go away to be sorted anyway for the exhaust manifold studs to be replaced and the log manifold is also on the list to be refaced as well.
Just need to borrow a valve spring compressor from somewhere
Anyone know how much the Febi rockers are ? - If its not noisy now would fitting new rockers without changing the camshaft make it better or worse ?
Thanks again for the words of advice people - much appreciated
First thing to do is get the head off and see exactly what I'm dealing with.
The cars done 143k so I guess its due a sympathetic head rebuild anyways.
I guess if I can get it stripped down to a bare head as per the Wiki guide a machine shop will be able to tell me if the guides are worn and need replacement - it will need to go away to be sorted anyway for the exhaust manifold studs to be replaced and the log manifold is also on the list to be refaced as well.
Just need to borrow a valve spring compressor from somewhere
Anyone know how much the Febi rockers are ? - If its not noisy now would fitting new rockers without changing the camshaft make it better or worse ?
Thanks again for the words of advice people - much appreciated

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
i think febi ones are about 150 from gsf or ecp 
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
Ouch.
I'll probably let the machine shop have a look and comment on whether they need replacing or not first then.
I'll probably let the machine shop have a look and comment on whether they need replacing or not first then.

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
just put your rockers in a vice and linish the face so that there is no sign of wear there. just make sure there is no play on the shafts as if there is play there you will never be able to adjust the clearance properly,
i have found the febi rockers don't last as well as the original whether they are the same part or not!!!! not sure why but never had any luck with them! but then i've always had a good stock of second hand ones to use!
i have found the febi rockers don't last as well as the original whether they are the same part or not!!!! not sure why but never had any luck with them! but then i've always had a good stock of second hand ones to use!
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Febis will last a damn site longer than "linishing" whats left of any of the running surface. Once that finish is worn through they wear at a faster rat and form the concave shape instead of concave.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
thats why they have a linish to put them back to a convex finish but i only linish if they arn't nearly worn through!!!!
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
the wear pads are only hard faced, once this has been removed, the pads will wear out like fook.....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
the febi ones may be but they are a block of the same material until you get to the alloy rocker itself????
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
it is a little square of the same material, but the hard facing is only a few microns deep.
once the hard face has been removed, you will be supprised how soft the material is.
once the hard face has been removed, you will be supprised how soft the material is.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
not that supprised lol!!!!
either way i think this poor old uy has got plenty of info to chew through now!!!!
either way i think this poor old uy has got plenty of info to chew through now!!!!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The slightest wear on any of these components and they are scrap!!kam-325i wrote:the hard facing is only a few microns deep.
IF your M20 has seen regular servicing with a decent quality oil, I wouldn't expect anything on a M20 head to be worn, except for the exhaust valve guides.
New guides, all valves faced up, their seats lightly recut, and the lightest skim that you can get away with on the head face (plus the studs sorted), and the head should be like new.
It's still necessary to check everything, of course, but I wouldn't expect to have to replace anything else as a matter of course.
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
febi make the BMW rockers 100% this is utter dross. Again don't listenTay wrote:just put your rockers in a vice and linish the face so that there is no sign of wear there. just make sure there is no play on the shafts as if there is play there you will never be able to adjust the clearance properly,
i have found the febi rockers don't last as well as the original whether they are the same part or not!!!! not sure why but never had any luck with them! but then i've always had a good stock of second hand ones to use!
Without sounding rude of the M20's now that are out there with 150k plus milege. But 99% will have had skipped oil changes etc by this age. The myth of the serviced engine with the oil done on the button by now is just that a myth and Rob go in eyes open expecting to find some wear on the cam and rockers.
I'll eat my hat if you don't what brian is saying is true if they are looked after but we all know now that cars like the one you bought don't fall into that category.
Budget £500 to do it all. And that will be once and properly as the others have said. Its not alot really is it for what you can get back in return of years of trouble free motoring.
-
SGP
- E30 Zone Regular

- Posts: 502
- Joined: Thu Aug 31, 2006 11:00 pm
Be very sure it's not just the valve cover gasket that's leaking before you pull the engine apart.
If it ain't broke..
Fix it till it is
Fix it till it is
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
Its definately leaking from the front of the head - I pressure washed it all clean in the summer and since then you can see exactly where its coming from. Its got to come off anyway to sort the broken exhaust studs.SGP wrote:Be very sure it's not just the valve cover gasket that's leaking before you pull the engine apart.
£500 isnt too bad I guess if that will do a thorough job - will just need to try and save up quick as I would like to tax insure and start using it on 1st April !
If the rockers do need replacement will the eccentric adjusters also need renewing ?

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Tay, are you Polish by any chance?
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
Far from it, just a very good and renowned mechanic, and I know not everyone wants to or can afford new parts! I know if I don't have to spend then I won't just like everyone else! I know alot of garages and guys who like to spend other peoples money but not their own when it comes to them having to repair their own car???
Right or wrong????
Right or wrong????
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
i just do it the right way and once. Or try, You get enough dramas that way let alone f**king about buffing worn rockers with emery and torquing heads down with less force than the wheel nuts!
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
calm down flashy only trying to help and if your doing your wheel nuts up to that then there's definitly something wrong!!! lol
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
About 20 minutes ago I torqued up a set of BMW wheel bolts - to 100Nm, which, if my memory serves, is around 75 lb ft - considerably more than you claim to torque head bolts to!Tay wrote:calm down flashy only trying to help and if your doing your wheel nuts up to that then there's definitly something wrong!!! lol
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
thats far more than i've ever put on a wheel bolt!
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
My point exactly. If the rockers are worn flat of concave, then they are scrap. The case hardened finish has long gone.kam-325i wrote:the wear pads are only hard faced, once this has been removed, the pads will wear out like fook.....
Tay, Where abouts is your workshop mate?
B7's Motto. "If it's French, BURN IT!!!!!!"
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
used to be in the middle of norfolk, now do free lance stuff around toytown along side my permenant job, until i go outside in a year or 2 then back to norfolk to work for the old boss again!
so little hope of getting hold of me unless you want work done!! lol i only say that due to some of the feedback i've been getting!!!!
so little hope of getting hold of me unless you want work done!! lol i only say that due to some of the feedback i've been getting!!!!
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Do you have a thread on your own cars full restoration Tay? Id love to see some info, I bet a man of your knowledge/experience managed the full engine rebuild for about £27 eh?
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
Hahahahahaha only a few photos! As it stands the engine to built only cost me the price of the headset, oil and filter”¦”¦
I kind of remember why I stopped posting on here”¦”¦ because everyone that knows all know the correct way which is theirs? I've just been trying to pass on my knowledge and getting shot down for it, possibly because I'm a newbee even though I've been a user since '05-06????
The methods I have said work do work, they've been tried and tested. I'm sorry if I don't like spending other people's money like water by buying all new parts!! Even my car is a good example finished it 2 years ago and not had the slightest problem just like all of my customers.
So if your still bent on giving me stick then crack on I ain't going far. But for a site that's supposed to help other 30 owners out”¦”¦ is it really when there is half a dozen of you that won't accept other ways of doing things? You should read the thread chat about abuse!!!! Not saying this is but the guys have been scratching around this sort of issue”¦”¦”¦
And breath!!!
I kind of remember why I stopped posting on here”¦”¦ because everyone that knows all know the correct way which is theirs? I've just been trying to pass on my knowledge and getting shot down for it, possibly because I'm a newbee even though I've been a user since '05-06????
The methods I have said work do work, they've been tried and tested. I'm sorry if I don't like spending other people's money like water by buying all new parts!! Even my car is a good example finished it 2 years ago and not had the slightest problem just like all of my customers.
So if your still bent on giving me stick then crack on I ain't going far. But for a site that's supposed to help other 30 owners out”¦”¦ is it really when there is half a dozen of you that won't accept other ways of doing things? You should read the thread chat about abuse!!!! Not saying this is but the guys have been scratching around this sort of issue”¦”¦”¦
And breath!!!
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
OK I've got the info I needed from this thread now and don't want it to degenerate into a bunfight as theres been too many of them of late.
Thanks to all contributors for their input
I will update my resto thread when the head comes off.
Mods feel free to lock this up.
Thanks to all contributors for their input
I will update my resto thread when the head comes off.
Mods feel free to lock this up.

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Judging by what you've been preaching, I wouldn't let you near a lawnmower. Reusing old headbolts (£14 a set new) and farting about refacing shagged out rockers is sheer bodgery.Tay wrote:Far from it, just a renowned bodger
Still, back to Norfolk for more broom and kettle duties soon eh?
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
lmaoAndyboy wrote:Tay wrote:Far from it, just a renowned bodger
Still, back to Norfolk for more broom and kettle duties soon eh?
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
lol not quite, as i live about 300 miles away now?!
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Don't worry - a member of the Institute of Master Bodgers can always find his way back! 

