LSD bolt hanging out

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
StevE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 177
Joined: Tue Jan 02, 2007 11:00 pm
Location: Taunton

Post Wed Jan 04, 2012 10:02 pm

Image

Its a bad picture but can anyone identify where this bolt has come from?

looks like it hasn't sheered off from anywhere. went bang over a bump and theres now a bolt sticking out of the rear casing.

still has drive as it was loaded on and off a trailer. Is it likely to have caused damage inside the diff or is it a case of a new back casing and its good to go again?

I bought the diff on here over a year ago but covered less than 4000 miles, do you think a bolt could have dropped in before I bought the diff and somehow it has managed to go this far without it happening? there were a couple knocks from the diff in the past.

FYI its a 3.25 ratio LSD.

thanks
Steve
Image
MrBenn
E30 Zone Regular
E30 Zone Regular
Posts: 672
Joined: Sun Jan 20, 2008 11:00 pm
Location: Bradford-on-Avon, Wiltshire

Post Thu Jan 05, 2012 9:26 am

Isn't that the drain plug?
Sjoerd320i
E30 Zone Addict
E30 Zone Addict
Posts: 4035
Joined: Mon Jan 10, 2005 11:00 pm
Location: Heemskerk, Holland

Post Thu Jan 05, 2012 10:13 am

MrBenn wrote:Isn't that the drain plug?
Sure is...

Wouldn't drive it anymore as the diff is empty.
Image
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 10:45 am

Its hard to see from that photo,

The sump plug is normally much larger in diameter.

Your poly bush doesnt look too clever either!

Andrew
User avatar
StevE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 177
Joined: Tue Jan 02, 2007 11:00 pm
Location: Taunton

Post Thu Jan 05, 2012 11:10 am

I've now got a better pic if it helps.

Image

thanks
Image
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 11:16 am

That looks like a flange bolt. Only the crown has those holding it on. Without taking the diff apart i would not risk driving on it. You run the risk of locking the rear wheels if any more bolts drop out.

That said, there is very little room for them to simply drop out, so expect damage inside!

Take it off and have it rebuilt.

Andrew
Curr946
E30 Zone Regular
E30 Zone Regular
Posts: 425
Joined: Tue Dec 23, 2008 11:00 pm
Location: Inverkeithing Fife

Post Thu Jan 05, 2012 11:18 am

I would be getting the back plate off get the inners washed out with some petrol then new back plate on with some fresh oil and crossing my fingers
If your wife must learn to drive, don't stand in her way!
MrBenn
E30 Zone Regular
E30 Zone Regular
Posts: 672
Joined: Sun Jan 20, 2008 11:00 pm
Location: Bradford-on-Avon, Wiltshire

Post Thu Jan 05, 2012 11:18 am

Woah! That looks like one of the bolts from LSD unit has worked loose, dropped off and punched the drain plug off of the back plate!

Oops too slow, already been answered.
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Thu Jan 05, 2012 11:29 am

what has happened to your polybush?
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Thu Jan 05, 2012 11:40 am

Yikes, looks fooked :clin:
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
craigieeb
E30 Zone Addict
E30 Zone Addict
Posts: 4988
Joined: Mon Jan 10, 2005 11:00 pm
Location: In my man cave modifying... something

Post Thu Jan 05, 2012 1:31 pm

StevE30 wrote:I've now got a better pic if it helps.

Image

thanks
That's quite impressive,

Has someone been in there before you bought it, and had a bit of a fiddle....?

Or just a freak occurrence,

Either way it's fooked!!
M50 Turbo!!! :o I shall say no more :D
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 1:36 pm

I dont think its a goner, just needs to be inspected, you could repair that on the car!

Andrew
Tom_Maverick
E30 Zone Camper
E30 Zone Camper
Posts: 1343
Joined: Wed Aug 25, 2010 11:00 pm
Location: Brighton

Post Thu Jan 05, 2012 2:57 pm

does the diff have a magnetic drain plug? if so the bolt could have floated about in the case for a short while till it got stuck to the magnetic plug and then while things were turning 'stood up' against the drain plug over a bump or suchlike and just punched the whole plug and surrounding ally out..
Image
User avatar
StevE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 177
Joined: Tue Jan 02, 2007 11:00 pm
Location: Taunton

Post Thu Jan 05, 2012 8:20 pm

4 missing bolts and 2 on the way out. Looks like the only thing damaged is the speed sensor wheel which is now loose. How is this normally held in place?

The edges of the poly bush are broken too.

Image

http://s72.photobucket.com/albums/i182/ ... -53-53.mp4

The person that put this together (bought off a zoner) should probably buy a new torque wrench with the money I paid for the diff.

Somehow it managed a trip to Gatwick and back like this. :o

thanks for the help.
Steve
Image
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 8:28 pm

The speed trigger needs to be heated up and pressed on as its an interference fit that keeps it on.

I would pull the diff and clean the bolt holes till they are dry and then use loctite to secure the bolts.

Its a pain but it looks like minimal damage has been done!

Andrew
Tom_Maverick
E30 Zone Camper
E30 Zone Camper
Posts: 1343
Joined: Wed Aug 25, 2010 11:00 pm
Location: Brighton

Post Thu Jan 05, 2012 10:04 pm

Lucky lucky! Thank Christ you didn't do more damage.. :)
Image
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 10:10 pm

I've just watched the video, it looks like the LSD is not working either, it should not be making that clicking noise, something is seriously damaged inside!
User avatar
StevE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 177
Joined: Tue Jan 02, 2007 11:00 pm
Location: Taunton

Post Thu Jan 05, 2012 10:40 pm

Demlotcrew wrote:I've just watched the video, it looks like the LSD is not working either, it should not be making that clicking noise, something is seriously damaged inside!
Are you sure its not the speed trigger?

there is still quite a bit of resistance to turn the wheel with the other wheel on the ground.
Image
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Thu Jan 05, 2012 11:02 pm

There's also a stray washer on the left-hand output shaft coupling. :mad:
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Thu Jan 05, 2012 11:52 pm

Ouch!
Right, that's not something i've seen before! To remove those bolts usually requires a 1/2" breaker bar and an extension! tight and retained with some strong loctite! I suspect it's been bodged together from two diffs to get a LSD in another ratio.

It's hard to pinpoint the source of the noise but it could be gear damage. Check the teeth on the crownwheel (the big gear you can see) carefully for any damage caused by the stray bolt. If there's damage, it's need a full rebuild with a new crownwheel and pinion. There's also a very good chance of bolt / casing fragments in the bearings.

PM on it's way :thumb:
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Fri Jan 06, 2012 10:11 am

StevE30 wrote:
Demlotcrew wrote:I've just watched the video, it looks like the LSD is not working either, it should not be making that clicking noise, something is seriously damaged inside!
Are you sure its not the speed trigger?

there is still quite a bit of resistance to turn the wheel with the other wheel on the ground.
Apologies, i thought both wheels were in the air. That noise could just be the clutch pack working, but i have never heard it make that sound before.

I always heat the crown before its tightened down with the flange bolts and loctite. As the crown cools, it clamps the flange bolts and secures them in place, You cannot be sure otherwise.

I would not attempt to fix it in situ, Its not that hard to pull the diff apart to see whats going on.

Andrew
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Fri Jan 06, 2012 10:32 am

One fooked LSD! :eek:
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Fri Jan 06, 2012 10:35 am

Its one of the reasons why i would never use Polly on my car, it doesn't last very long!
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Fri Jan 06, 2012 10:59 am

Demlotcrew wrote:Its one of the reasons why i would never use Polly on my car, it doesn't last very long!
Seems that this problem with the diff poly mount is quite common. It sags.
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Fri Jan 06, 2012 11:04 am

Its not the best solution, its a solution that has been well marketed and is relatively inexpensive!
User avatar
Kos
E30 Zone Team Member
E30 Zone Team Member
Posts: 15448
Joined: Tue Jul 12, 2005 11:00 pm
Location: London / Cyprus

Post Sun Jan 08, 2012 1:28 am

i've been saying it for years that the polly bushes for diffs are crap and fail and cause more damage

Z3M diff bush is fine for any fast road car and track car.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 08, 2012 10:22 am

Kos wrote:i've been saying it for years that the polly bushes for diffs are crap
Extend that to include all bushes on an E30, and I fully agree!
User avatar
Kos
E30 Zone Team Member
E30 Zone Team Member
Posts: 15448
Joined: Tue Jul 12, 2005 11:00 pm
Location: London / Cyprus

Post Sun Jan 08, 2012 5:22 pm

Brianmoooore wrote:
Kos wrote:i've been saying it for years that the polly bushes for diffs are crap
Extend that to include all bushes on an E30, and I fully agree!
Agreed

Ps, I sent you a pm ages ago, it's still in my out box !!!
pacerpete
E30 Zone Team Member
E30 Zone Team Member
Posts: 18165
Joined: Sun Jan 23, 2005 11:00 pm
Location: Iver heath. South bucks.

Post Sun Jan 08, 2012 5:40 pm

Kos wrote:
Brianmoooore wrote:
Kos wrote:i've been saying it for years that the polly bushes for diffs are crap
Extend that to include all bushes on an E30, and I fully agree!
Agreed

Ps, I sent you a pm ages ago, it's still in my out box !!!

He is probably too scared to open it ! :eek: :)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 08, 2012 9:07 pm

Kos wrote:
Brianmoooore wrote:
Kos wrote:i've been saying it for years that the polly bushes for diffs are crap
Extend that to include all bushes on an E30, and I fully agree!
Agreed

Ps, I sent you a pm ages ago, it's still in my out box !!!
90 messages in my inbox, going back to June last year, Kos
None of them from you!
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Sun Jan 08, 2012 9:36 pm

Brianmoooore wrote:
Kos wrote:
Brianmoooore wrote: Extend that to include all bushes on an E30, and I fully agree!
Agreed

Ps, I sent you a pm ages ago, it's still in my out box !!!
90 messages in my inbox, going back to June last year, Kos
None of them from you!
I can only fit about 20 in my inbox :eek:

How about a solid aluminium diff bush?
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Sun Jan 08, 2012 9:40 pm

solid would transmit stress's to the chassis.

The idea behind the rubber bush is to absorb some of the stress's.....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
User avatar
Kos
E30 Zone Team Member
E30 Zone Team Member
Posts: 15448
Joined: Tue Jul 12, 2005 11:00 pm
Location: London / Cyprus

Post Tue Jan 10, 2012 8:36 pm

redcar wrote:
Brianmoooore wrote:
Kos wrote: Agreed

Ps, I sent you a pm ages ago, it's still in my out box !!!
90 messages in my inbox, going back to June last year, Kos
None of them from you!
its out of my out box now......
redcar wrote: I can only fit about 20 in my inbox :eek:

How about a solid aluminium diff bush?

team members have more inbox space than us commoners