crankshaft oil seal replacement

Need technical Q/A then you're in the right place

Moderator: martauto

steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Wed Dec 07, 2011 8:02 pm

right then folk's

found out today that i've got a slight oil leak on the car (1990 325i) & it looks like it's coming from the front of the engine around the crankshaft oil seal area.

now thing is if it is coming from there then how hard is it to replace it?

never had to do it before so it'll be my first time :o:
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Dec 07, 2011 10:01 pm

Are you sure? It would be very unusual if it was. Crank seals don't normally give trouble, front or rear.
Biggest problem is getting the crank pulley bolt undone, which is done up to a torque well past the top end of most torque wrenches. An effective way is to place a block of wood on the chassis rail, a 22mm ring spanner on the bolt, and engage the starter motor.
Cam belt has to come off and be renewed, of course, and remember not to turn the crank once the belt's off, or you'll be removing the head and replacing bent valves.
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Thu Dec 08, 2011 6:05 pm

I've had two fail, the front seal on an E21 323i and same again on an M30 engine.
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Wed Dec 14, 2011 11:04 am

Well it look's like i've sussed where the oil leak is :)

& thankfully it ain't the crankshaft oil seal :D

it look's to be coming from the oil filter area so it must be the O ring gasket on the oil filter (going to change the oil & filter anyway) so finger's crossed that's it.
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Wed Dec 14, 2011 11:29 am

Brianmoooore wrote:An effective way is to place a block of wood on the chassis rail, a 22mm ring spanner on the bolt, and engage the starter motor.
good tip brian

it's even more fun with the engine out 8O

i had to jack a scrap car up and slide the block under on a piece of wood, put an old engine arm on and wedge it under the car, and even then I needed a 2m pipe to crack off the bolt
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Dec 14, 2011 1:27 pm

steve_k wrote:

it look's to be coming from the oil filter area so it must be the O ring gasket on the oil filter (going to change the oil & filter anyway) so finger's crossed that's it.
Check out an approx. 20mm diameter plug in the underside of the oil filter mounting block, held in place by a circlip. BMW made a design fault here with the choice of material for the sealing O ring, and an improved design is available as a small kit of parts for about £4 or so.
Don't let the oil cooler thermostat fall out when you remove the plug.
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Wed Dec 14, 2011 7:19 pm

Brianmoooore wrote:
steve_k wrote:

it look's to be coming from the oil filter area so it must be the O ring gasket on the oil filter (going to change the oil & filter anyway) so finger's crossed that's it.
Check out an approx. 20mm diameter plug in the underside of the oil filter mounting block, held in place by a circlip. BMW made a design fault here with the choice of material for the sealing O ring, and an improved design is available as a small kit of parts for about £4 or so.
Don't let the oil cooler thermostat fall out when you remove the plug.
cheers for that brian :D job for tomorrow then.

would you happen to have a part number for that "kit"?
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Dec 14, 2011 7:26 pm

11 42 9 059 338
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Wed Dec 14, 2011 7:31 pm

Brianmoooore wrote:11 42 9 059 338
topman thanks brian :cool:
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Tue Jan 03, 2012 11:00 pm

well i found out that i DO have a slight leak from around the oil filter but the main one i was worried about ain't the crankshaft oil seal at all.

it is a power steering rack leak so when i get a dry day i'll be under the car to see if it can be fixed quickly & cheaply.

strange thing is the fluid level hardly drops (been checking it every other day).

just hoping i get a dry day tomorrow.
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Tue Jan 03, 2012 11:51 pm

give the rubber rack boots a squeeze to see if theres any PAS fluid in them. If not, probably an easy fix by a new banjo bolt crush washer and/or jubilee clamp on the bottom of the PAS reservoir to replace the standad clips which can leak over time
Image