Fiiting power steering+ e36 rack
Moderator: martauto
-
P10mike
- E30 Zone Regular

- Posts: 251
- Joined: Fri May 01, 2009 11:00 pm
- Location: fife
I'm looking to fit an e36 rack and power steering as i'm fed up with the keep fit steering and just wanted to check if i need anything else for it before i start. So far i have,
e36 rack + e30 rods and ends
PAS pump
Correct pipes
Belt
Resevoir with hose.
Am i right in thinking i also need a crank pulley?
e36 rack + e30 rods and ends
PAS pump
Correct pipes
Belt
Resevoir with hose.
Am i right in thinking i also need a crank pulley?
-
maxfield
- Old Skooler

- Posts: 15185
- Joined: Sat Nov 26, 2005 11:00 pm
- Location: Mansfield
Spacers for rack and subrame.
And something for the steering linkage. Seems DanThe is the man for the linkages...
And something for the steering linkage. Seems DanThe is the man for the linkages...

-
mattrs
- E30 Zone Squatter

- Posts: 1810
- Joined: Fri Apr 18, 2008 11:00 pm
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
What engine do you have in your e30
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Apart from 'bolting the rack to the subframe' I dont see the relevance
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Lhd cars don't have to worry about their steering linkage hitting the manifold
-
P10mike
- E30 Zone Regular

- Posts: 251
- Joined: Fri May 01, 2009 11:00 pm
- Location: fife
Oh forgot to say i have a machined centre with an e30 uj on one end and an e36 uj on the other.
Also have the washers for the spacing.
Wasn't sure about the pulley though, is it hard to fit?
Also have the washers for the spacing.
Wasn't sure about the pulley though, is it hard to fit?
-
Curr946
- E30 Zone Regular

- Posts: 425
- Joined: Tue Dec 23, 2008 11:00 pm
- Location: Inverkeithing Fife
Mike I have a pulley here if you need it 
If your wife must learn to drive, don't stand in her way!
-
P10mike
- E30 Zone Regular

- Posts: 251
- Joined: Fri May 01, 2009 11:00 pm
- Location: fife
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
Here's the ultimate guide Mike
http://www.e30zone.net/modules.php?name ... light=rack
This tells you everything and is where I got the info to make the spacer you have
http://www.e30zone.net/modules.php?name ... light=rack
This tells you everything and is where I got the info to make the spacer you have
-
mattrs
- E30 Zone Squatter

- Posts: 1810
- Joined: Fri Apr 18, 2008 11:00 pm
DanThe wrote:Apart from 'bolting the rack to the subframe' I dont see the relevance
I obviously thought a link to a step by step pictorial guide with part numbers of a e36 rack conversion would be pretty handy for the op as he is inquiring about doing just that!
Or am I missing something?
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
The link you gave is for left hand drive cars, we have right hand drive so everything apart from the bolts through the rack is different
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
The link I've posted is for right hand drive and is the best I've ever found after hours of searching
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Yes your guide is good
I use that lonkage
I use that lonkage
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
PAS rack should be mounted in the rear holes FYI
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
hi buddy do you have an e36 rack on an m42 e30?rossmc88 wrote:Here's the ultimate guide Mike
http://www.e30zone.net/modules.php?name ... light=rack
This tells you everything and is where I got the info to make the spacer you have
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
not yet, but I have a Z3 rack to fit. I had everything I needed before, but sold it to Mike when I got rid of my E30. Then I bought another E30, this time an M42, so bought a Z3 rack for it since it's a keeper. I'm saving up for new arms, track rods and drop links before I fit itredcar wrote:hi buddy do you have an e36 rack on an m42 e30?rossmc88 wrote:Here's the ultimate guide Mike
http://www.e30zone.net/modules.php?name ... light=rack
This tells you everything and is where I got the info to make the spacer you have
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
oh ok and what linkage are you going to use. Standard e30 with different guibo or an e30/e36 hybrid?rossmc88 wrote:not yet, but I have a Z3 rack to fit. I had everything I needed before, but sold it to Mike when I got rid of my E30. Then I bought another E30, this time an M42, so bought a Z3 rack for it since it's a keeper. I'm saving up for new arms, track rods and drop links before I fit itredcar wrote:hi buddy do you have an e36 rack on an m42 e30?rossmc88 wrote:Here's the ultimate guide Mike
http://www.e30zone.net/modules.php?name ... light=rack
This tells you everything and is where I got the info to make the spacer you have
Im using the hybrid but the lower UJ is very close to the manifold. Ordered some new poly engine mounts and hopefully that solves it.
Is a z3 rack the exact same as an e36 rack in terms of the shafts etc.?
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
The Z3 rack is better as the splines match on both ends, so I don't have to make a hybrid like I did for the E36 rack kit I sold Mike. I'll still have to make a 22mm spacer like I did before to create the extra length needed.
Are you fitting the rack to an M42? If so, get some solid M50 e34 mounts from euro car parts - £30 ish pounds and this will raise the enging slightly and help with the clearance. This is what I'm going to do for my M42 installation
Are you fitting the rack to an M42? If so, get some solid M50 e34 mounts from euro car parts - £30 ish pounds and this will raise the enging slightly and help with the clearance. This is what I'm going to do for my M42 installation
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Was thinking of doing that but didn't want to raise the engine an extra 8mm.rossmc88 wrote:The Z3 rack is better as the splines match on both ends, so I don't have to make a hybrid like I did for the E36 rack kit I sold Mike. I'll still have to make a 22mm spacer like I did before to create the extra length needed.
Are you fitting the rack to an M42? If so, get some solid M50 e34 mounts from euro car parts - £30 ish pounds and this will raise the enging slightly and help with the clearance. This is what I'm going to do for my M42 installation
So i decided to buy some poly m42 e30 engine mounts. Engine shouldn't be moving at all!
I've heard even a few mm clearance from the uj and the manifold is good enough as long as your engine mounts don't let the engine move at all.
I just need to get some e21 gearbox mounts. Don't really want poly on the gearbox as it might vibrate.
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
How much were your poly engine mounts and where from? Would the e34 mounts raise the engine as much as 8mm?
Yeah I've read you only need a couple of mm clearance too
I would get a DanThe linkage, but I can get the spacers made up at my work for free
Yeah I've read you only need a couple of mm clearance too
I would get a DanThe linkage, but I can get the spacers made up at my work for free
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
No need for us to have a new linkage, the linkage isn't the problem its just the lower UJ which is the problem.rossmc88 wrote:How much were your poly engine mounts and where from? Would the e34 mounts raise the engine as much as 8mm?
Yeah I've read you only need a couple of mm clearance too
I would get a DanThe linkage, but I can get the spacers made up at my work for free
I got mine from revshift, they were $150 shipped. those e28 mounts which fit are 63mm whereas m42 mounts are 55mm.
Wouldn't really want to raise the engine.
-
TamTom
- E30 Zone Newbie

- Posts: 181
- Joined: Thu Sep 24, 2009 11:00 pm
i want to do this project to my m42, i bought a 95 e36 m3 evo rack can i use all the old pipes etc?
will the e30 Universal joint fit the e36 one?
will the e30 Universal joint fit the e36 one?
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
I think you need the e36 lower uj as the splines on e30 and e36 are different
Make a hybrid e30 / e36 shaft
Make a hybrid e30 / e36 shaft
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
PAS rack splines are all the same from what ive seen
-
suhinaffy
- E30 Zone Regular

- Posts: 355
- Joined: Tue Jul 06, 2010 11:00 pm
- Location: Fife
If you need a hand fitting it give me a phone.
-
P10mike
- E30 Zone Regular

- Posts: 251
- Joined: Fri May 01, 2009 11:00 pm
- Location: fife
Cheers bud i still need to get a few bits for it so i will be fitting the exhaust first and the rack in a month or so.

