temp rises in traffic!

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
adi1987
E30 Zone Newbie
E30 Zone Newbie
Posts: 37
Joined: Thu Dec 15, 2011 11:00 pm

Post Fri Dec 30, 2011 8:27 pm

I'm just wondering if anyone can point me in the right direction, my 320 has been getting up to just over 3/4 on the temp guage in heavy traffic, it doesn't get any higher, and it does seem to take quite a while to get warm in the cold mornings.
DHFiS
Old Skooler
Old Skooler
Posts: 2733
Joined: Sat Aug 12, 2006 11:00 pm
Location: cambridge

Post Fri Dec 30, 2011 8:29 pm

Thermostat stuck half open can lead to these symptoms
User avatar
adi1987
E30 Zone Newbie
E30 Zone Newbie
Posts: 37
Joined: Thu Dec 15, 2011 11:00 pm

Post Fri Dec 30, 2011 8:39 pm

Thats what I thought, but could it be anything to do with the fan? I've never had to deal with viscous fans so don't really know much about them
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Fri Dec 30, 2011 8:48 pm

likely to be your viscous fan.
johnl320
E30 Zone Addict
E30 Zone Addict
Posts: 3124
Joined: Mon Jan 10, 2005 11:00 pm
Location: Hampshire

Post Fri Dec 30, 2011 8:50 pm

My money is on the viscous fan and if you haven't owned the car very long maybe a previous owner has removed the thermostat to try and solve the initial fan issues.
User avatar
adi1987
E30 Zone Newbie
E30 Zone Newbie
Posts: 37
Joined: Thu Dec 15, 2011 11:00 pm

Post Fri Dec 30, 2011 10:34 pm

I'd have to double check but I think the fan runs at a fairly steady speed no matter how high the temperature is, I guess if the temp gets too hot the fan speeds up?
mr_dink
E30 Zone Regular
E30 Zone Regular
Posts: 812
Joined: Thu Jan 03, 2008 11:00 pm
Location: Huddersfield

Post Fri Dec 30, 2011 10:38 pm

The fan will spin even if the viscous coupling has gone, but it wont be moving enough air.

The test is to use a rolled up newspaper to try to stop the fan when the engine is running and warm. If you can stop the fan, the viscous coupling is dead.
User avatar
adi1987
E30 Zone Newbie
E30 Zone Newbie
Posts: 37
Joined: Thu Dec 15, 2011 11:00 pm

Post Fri Dec 30, 2011 10:43 pm

Ahh good idea, will try that. Is it an easy enough job to change it? I see some on ebay, "4 bolt" couplings, quite a few at around £30 posted, is this what I will need?
Blitz
Married to the E30 Zone
Married to the E30 Zone
Posts: 11151
Joined: Mon Jan 30, 2006 11:00 pm
Location: East London+Basildon

Post Sat Dec 31, 2011 1:03 am

adi1987 wrote:Ahh good idea, will try that. Is it an easy enough job to change it? I see some on ebay, "4 bolt" couplings, quite a few at around £30 posted, is this what I will need?
Cheap ones dont last long when I used one. GSF sell a Sachs/Boge one for £60
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Sat Dec 31, 2011 1:27 am

they can be a pain to remove as sometimes hooligans use loctite on the thread, which causes all sorts of aggro.

It is a 32mm nut and it is a left hand thread that holds the viscous onto the water pump
User avatar
adi1987
E30 Zone Newbie
E30 Zone Newbie
Posts: 37
Joined: Thu Dec 15, 2011 11:00 pm

Post Sat Dec 31, 2011 11:17 am

if its a left handed thread then loctite isn't needed... some people have no common sense lol

Is there any easy way of locking it while trying to undo the big nut? I don't want to be breaking the fan or jamming my pry bar into the viscous for it to just fall to bits haha. It only seems to be affecting it in heavy traffic and it hasn't actually gone much above 3/4. When I go back to work its a 10 mile trip on main roads so it should be OK until payday.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Dec 31, 2011 2:20 pm

If the coupling was fitted properly, a sharp smack with a hammer on the handle of the 32mm spanner should be enough to start it unscrewing.
If this doesn't work, unscrew one of the four 6mm bolts that hold the pulley to the water pump, take a piece of flat steel bar, about 3mm x 20mm x 300mm, drill a 6.5mm hole close to one corner, than take a slightly longer 6mm bolt than the one you removed, and bolt the bar to the pump hub. Turn the pulley untill the bar locks against the hub, and use the 32mm spanner to undo the fan.