Is my Radiator Fooked???? Pics Added.

Need technical Q/A then you're in the right place

Moderator: martauto

Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Tue Dec 27, 2011 9:43 pm

Hi Folks need some advice The car is a 89 pre facelift 325i auto cabby.

The car was ran for the first time in about a month and the small pipe that goes from the top of the expansion tank to the top of the radiator flew off once the car was upto temp and coolant poured out every where.

It looks like its been bodged in the past as as the small metal pipe (about 3mm accross) that goes inside the radiator and the pipe to the expansion tank had been glued in.

Is this new radiator time or is there any good fix? Dont want to glue it back it.
Last edited by Rtaylor2208 on Thu Dec 29, 2011 1:55 pm, edited 1 time in total.
zaust
Zone day release
Posts: 13007
Joined: Sun Jan 09, 2005 11:00 pm
Location: Somewhere in Hertfordshire , or press Ctrl + W

Post Wed Dec 28, 2011 3:47 pm

Its more Likely the coolant bottle cap has a failed seal. A new one is around £6 from the dealers. Try this first.
M30 Tech 1 Touring on gas.
Image
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Wed Dec 28, 2011 4:32 pm

Zaust, thanks for the reply but why would the metal pipe going into the radiator snap off if the cap seal has failed. When pushed back in it doesnt hold tight so as soon as the thermostat opens and coolant starts pumping round the engine it goes again.

I can see where the plastic outer coating to the inner metal pipe had been broke off in the past. I'll try and post a pic up later better explaining the problem.
zaust
Zone day release
Posts: 13007
Joined: Sun Jan 09, 2005 11:00 pm
Location: Somewhere in Hertfordshire , or press Ctrl + W

Post Wed Dec 28, 2011 9:56 pm

You have a separate tank to the rad ? If so it should be a case of new tank. If the tank Is attached to the rad then new rad as its a ballache to replace just the tank.
M30 Tech 1 Touring on gas.
Image
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Thu Dec 29, 2011 1:36 pm

OK, Some pictures attached to help explain.

Where the pipe has broken off from the Radiator
Image

The broken off pipe bit in the pipe itself:
Image

How it looks when attached:
Image
mrLEE30
E30 Zone Team Member
E30 Zone Team Member
Posts: 6589
Joined: Tue Jan 18, 2005 11:00 pm
Location: Sweating buckets in Bahrain

Post Thu Dec 29, 2011 2:23 pm

unfortuntely the radiator system works under a set pressure, as this increases the boiling point of the fluid, the expansion tank and that hose is subject to the same pressure so it would need to be a good tight fit to maintain the pressure

so unless you can find a company that is able to weld the plastic pipe back on in some way yes your rad is finished, for what its worth many compnaies recore radiators, but few are able to fix the end caps if broken, and certainly not if plastic....
Image
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Thu Dec 29, 2011 2:28 pm

mrLEE30 wrote:......... and certainly not if plastic....
That pipe is brass!

My radiator man would have no trouble in soldering a replacement pipe in....
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Thu Dec 29, 2011 2:36 pm

Thanks for looking folks. Daimlerman it did have a plastic surround round it before it snapped off, I think a new or replacement rad looks to be the way to go. I don't know anyone that does that kind of work and after a few phone calls this morning there doesn't appear to be any one local either.

2 steps forward, 3 back. The car managed a grand total of 237 miles since this time last year due to all these niggly problems. And thats before I start the expensive work of a new hood and paint. :cry: