Rear Hard Brake Lines
Moderator: martauto
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
I will be fitting the last of the rear brake lines - I have bought cunnifer and the unions but after seeing some pictures on here, there seems to be a clip that joins the flexi and hard pipes -
Looks like 6 on here...
http://bmwfans.info/parts/catalog/E30/C ... pipe_rear/
What do these clips do and do I need them as they are not on the diagram above?
Thanks
Looks like 6 on here...
http://bmwfans.info/parts/catalog/E30/C ... pipe_rear/
What do these clips do and do I need them as they are not on the diagram above?
Thanks
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
number 6 fits between hard lines and flexies to hold/secure them in place on body mounts
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Thanks for the heads up. Will order them tomorrow. Are they dealer only or would ECP do them do you know? Also how many would I need? Thanks
-
toby
- E30 Zone Addict

- Posts: 3609
- Joined: Thu Aug 11, 2005 11:00 pm
- Location: Kent
Tap your chassis number into the parts catalogue in this section and that may help. It's probably a dealer only part but you could check ECP's website.

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Hope you've used 'short' M10 male ends for your pipe, otherwise the clips won't fit.
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Yes ordered these. Will have a go tomorrow.Brianmoooore wrote:Hope you've used 'short' M10 male ends for your pipe, otherwise the clips won't fit.
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
Dealer only, or you may be able to re-use your old one's
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Yep thought so. They don't look expensive anyhow. 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Always worth replacing - they will have started to corrode, even if they are still passable.
I buy these in bulk, and they weren't expensive the last time I bought a batch, although that was a year or three ago.
Also, by far the easiest way to remove the old stuff, is to chop the hard lines just behind the pipe ends, and then destroy the clip.
I buy these in bulk, and they weren't expensive the last time I bought a batch, although that was a year or three ago.
Also, by far the easiest way to remove the old stuff, is to chop the hard lines just behind the pipe ends, and then destroy the clip.
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
They're pennies from BMW - you might even find they're in stock 

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
Wee bit of topic....Brianmoooore wrote:Hope you've used 'short' M10 male ends for your pipe, otherwise the clips won't fit.
Does that mean these: http://www.ebay.ie/itm/ws/eBayISAPI.dll ... SA:IE:1123 won't fit/work?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Doesn't say in the ad., but if that's a pic. of the actual item, it looks like it is the 'short' version.Jozi wrote:Wee bit of topic....Brianmoooore wrote:Hope you've used 'short' M10 male ends for your pipe, otherwise the clips won't fit.
Does that mean these: http://www.ebay.ie/itm/ws/eBayISAPI.dll ... SA:IE:1123 won't fit/work?
I'd like to find a source of 'short' brass ones, but have only managed to find 'long' ones.
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
They measure about 16-17mm top to bottom, look much like in the picture. If their the right ones I'm glad to find out now rather than realise their not when I get at the brakes.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
'Short' ones are 16.3mm and 'long' ones are 21.5mm, overall length. Just measured some.
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
Thanks for checking, it's short ones I have soBrianmoooore wrote:'Short' ones are 16.3mm and 'long' ones are 21.5mm, overall length. Just measured some.
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Not done this yet but will start tomorrow.
Quick question - are the flares single or double flares on the hard pipe?
I'll need to practise tonight as I've not done it for a long time!!
Quick question - are the flares single or double flares on the hard pipe?
I'll need to practise tonight as I've not done it for a long time!!
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Wow, bit over the top Brian? I find greasing them up everywhere before assembling gives them a long life, covered with waxoil afterwards of course.Brianmoooore wrote: I'd like to find a source of 'short' brass ones, but have only managed to find 'long' ones.
Ive taken apart joints that are only 12 months old and they have been seized up/rusted because eejits put them together dry
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
OK had a quick practise...

Left is Single Flared Joint
Middle is Double Flared Joint
Right is OLD BM pipe
Mine don't look like this? Any tips?

Left is Single Flared Joint
Middle is Double Flared Joint
Right is OLD BM pipe
Mine don't look like this? Any tips?
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Double flare.
what do yours look like ?
and what kit are you using ?
what do yours look like ?
and what kit are you using ?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
I suppose they look like the OE ones. The kit is as old as the world but still in very condition. Thanks will do Double flaring!
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Imagine the middle one once its been compressed 
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Do you think it needs compressing a little more?
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
NO. The middle one is fine........tom325sport wrote:Do you think it needs compressing a little more?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I doubt if it's older than mine - I've had it for around forty years, and like yours, it still makes perfect flares, and is easily used in confined spaces.tom325sport wrote: The kit is as old as the world but still in very condition.
The middle pipe is absolutely perfect. It'll take up its final shape when it's been used.
-
tom325sport
- E30 Zone Regular

- Posts: 819
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Guernsey
Thanks Brian that's great. Yes I inherited mine through an old neighbour who was an 80 year old mechanic before he
Retired and passed this on to me. It's used but in great condition!! I'm sure it will be used for more years to come. I don't think it's 40 years however.
Retired and passed this on to me. It's used but in great condition!! I'm sure it will be used for more years to come. I don't think it's 40 years however.

