Burnt wire
Moderator: martauto
-
RoadHazard
- E30 Zone Newbie

- Posts: 231
- Joined: Mon Oct 13, 2008 11:00 pm
- Location: Bangkok, Thailand
I have a burnt wire which goes between the fuse box and C103 through the firewall. It's bad enough to melt a few other surrounding wires. These wires are a part of the main loom. I want opinions how I should fix this please. I don't want to replace the whole loom. But since I can't tell which wires have been melted because of the tight space, should I go as far as replacing the whole bundle going to the fuse box? Of course I'm going to find out what caused the burnt in the first place as the first thing.
90 E30 S50B30
http://www.fquick.com/RoadHazard
http://www.fquick.com/RoadHazard
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
What pin on the C103? Wire colour would help as well if you can still make it out.
-
RoadHazard
- E30 Zone Newbie

- Posts: 231
- Joined: Mon Oct 13, 2008 11:00 pm
- Location: Bangkok, Thailand
Pin 11 yl/gn. The wire is burnt from the plug all the way to the relay K4 in the fuse box. It also melted a few other near by wires.
90 E30 S50B30
http://www.fquick.com/RoadHazard
http://www.fquick.com/RoadHazard
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
There's a second yellow/green wire going on from pin 11 on the 103 (to the steering column plug) and another one from the plug that pushes into the 103, that goes to the lighting switch.
Is either of these burnt?
I'm trying to get some idea of why and how a wire that is effectively an earth wire could get damaged like this. Best theory at the moment is that someone tried to bypass the relay by linking 30 to 87, and linked 30 to 85 instead.
I've no experience of this particular wire burning up, but I've seen a couple of cases where a similar sized brown earth wire that also goes down through the duct from the fusebox to behind the glovebox has burnt up (following an engine change) and in spite of the mess and masses of acrid smoke (as it burns), no shorts have occurred to adjacent wires. I think you may do more damage to adjacent wires if you try to pull the damaged wire out, as this is likely to tear strips of partly melted insulation, which has stuck to the burnt wire, completely off of the wires.
Is either of these burnt?
I'm trying to get some idea of why and how a wire that is effectively an earth wire could get damaged like this. Best theory at the moment is that someone tried to bypass the relay by linking 30 to 87, and linked 30 to 85 instead.
I've no experience of this particular wire burning up, but I've seen a couple of cases where a similar sized brown earth wire that also goes down through the duct from the fusebox to behind the glovebox has burnt up (following an engine change) and in spite of the mess and masses of acrid smoke (as it burns), no shorts have occurred to adjacent wires. I think you may do more damage to adjacent wires if you try to pull the damaged wire out, as this is likely to tear strips of partly melted insulation, which has stuck to the burnt wire, completely off of the wires.
-
RoadHazard
- E30 Zone Newbie

- Posts: 231
- Joined: Mon Oct 13, 2008 11:00 pm
- Location: Bangkok, Thailand
I have only told you about the burnt wire but not the story when it happened, so let me do it now:
On that day, I came to the car to find out that the low beams were staying on even though the switch was off. I was wondering what was going on so I turned on the lights. And there was smoke. I investigated further and found out that for the lights that turned on, they became off when the key is in Run/Start.
After looking at the ETM, I can conclude that somehow the yl/gn wire was touching a battery feed so when I turned on the light switch, the yl/gn got connected to ground and the short occurred. As one pole of the relay K4 connects to a Hot-in-Run feed, when the other pole touched a battery feed, the lights came on when the key was not in Run.
So I'll have to find out why the yl/gn was touching the battery. I've used this car for months and it just had to happen that day. And that was only a few hours after the last time I had used the low beams too.
BTW, the yl/gn wire that goes to the combo switch is not burnt. The only one burnt is the one from the C103 to the K4 relay. I haven't looked carefully at the loom under the front console yet but from what I can see, it's not burnt either. Maybe because of the fact that the wire is thicker in that loom.
On that day, I came to the car to find out that the low beams were staying on even though the switch was off. I was wondering what was going on so I turned on the lights. And there was smoke. I investigated further and found out that for the lights that turned on, they became off when the key is in Run/Start.
After looking at the ETM, I can conclude that somehow the yl/gn wire was touching a battery feed so when I turned on the light switch, the yl/gn got connected to ground and the short occurred. As one pole of the relay K4 connects to a Hot-in-Run feed, when the other pole touched a battery feed, the lights came on when the key was not in Run.
So I'll have to find out why the yl/gn was touching the battery. I've used this car for months and it just had to happen that day. And that was only a few hours after the last time I had used the low beams too.
BTW, the yl/gn wire that goes to the combo switch is not burnt. The only one burnt is the one from the C103 to the K4 relay. I haven't looked carefully at the loom under the front console yet but from what I can see, it's not burnt either. Maybe because of the fact that the wire is thicker in that loom.
90 E30 S50B30
http://www.fquick.com/RoadHazard
http://www.fquick.com/RoadHazard
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Like you say, it all fits with a direct short between the green/yellow wire and a permanent live, and if the damage extends to the fusebox, the short must have been here.
Apart from insulating the wire inside the fusebox, so that it doesn't happen again, I'd be tempted to leave well alone. Although it doesn't look pretty, the bubbled up plastic still seems to insulate well.
Apart from insulating the wire inside the fusebox, so that it doesn't happen again, I'd be tempted to leave well alone. Although it doesn't look pretty, the bubbled up plastic still seems to insulate well.
-
RoadHazard
- E30 Zone Newbie

- Posts: 231
- Joined: Mon Oct 13, 2008 11:00 pm
- Location: Bangkok, Thailand
I think I might have found the problem. There's a crack on the heat shrink insulator at the relay terminal. That may be where it touched the battery feed.
I looked more carefully at the melted wires today. They are melted together by the burnt wire and are likely to have their conductor exposed. I'll have to pull those out and replace with good wires. Since they are stuck together, I pretty much know which ones I have to work on. Some other wires are also melted but not as bad and can be left as they are, although not pretty like you said.
I looked more carefully at the melted wires today. They are melted together by the burnt wire and are likely to have their conductor exposed. I'll have to pull those out and replace with good wires. Since they are stuck together, I pretty much know which ones I have to work on. Some other wires are also melted but not as bad and can be left as they are, although not pretty like you said.
90 E30 S50B30
http://www.fquick.com/RoadHazard
http://www.fquick.com/RoadHazard
