Steam and overheating... Headgasket, or thermostat?

Need technical Q/A then you're in the right place

Moderator: martauto

cee
E30 Zone Regular
E30 Zone Regular
Posts: 983
Joined: Sun Aug 23, 2009 11:00 pm
Location: Plymouth

Post Wed Dec 21, 2011 3:33 am

So I had some issues with some breathers around the throttle body, replaced them all, and have since double checked everything and all seems fine.

However, once I got the car running again (was off the road for around 3 weeks) it ran perfectly for a few hours, then suddenly overheated, when I pulled over, it started to steam. The steam was coming from below the throttle body somewhere, (this is when I double checked all my work to make sure I hadn't missed a pipe or what not).

This problem got gradually worse as I test drove the car.

However, there is no oil fouling. Speaking with people and everyone seems to agree that it is either a thermostat issue or the head gasket, but no one seems sure which.

The car will heat up fairly quickly while driving at town speeds (5-10 mins) and will go straight to the red, and steam A LOT. However, the steaming can be stopped if pressure is reduced by opening the expansion tank cap.

I also noticed, while running with the cap off, that when the tank is 3/4 full, there is no steam/hissing, however, if I fill it up to the max line, it starts steaming and hissing...

Opinions? And sorry for the essay, just trying to get as much detail as possible...
Image
1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Wed Dec 21, 2011 8:36 am

Cooling fan working OK ?

Has the stat been replaced ?

"No oil fouling" - so no oil in the coolant or Mayo on the oil filler or dipstick ?

Assuming the fan is working and the system is properly bled I would be changing the stat first ( as its cheap ) and if that doesnt work take it to a garage and get them to do a "sniff test" before you invest any time and money taking the head off.
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
cee
E30 Zone Regular
E30 Zone Regular
Posts: 983
Joined: Sun Aug 23, 2009 11:00 pm
Location: Plymouth

Post Wed Dec 21, 2011 10:29 am

Coolant fan is permanently on.

Stat not replaced since I've owned the car (18 months).

No oil in coolant and no mayo, however there was a little mayo in some of the breathers I replaced, but I put that down to moisture within the pipes (as they were cracked and perished)...

I bled the system as best I could, and it only seemed to get worse, so seems not to be the issue.

I'm assuming it's worth spending the extra on a brand new stat rather than used, but your point seems sensible, so will try that. Thanks
Image
1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Wed Dec 21, 2011 10:54 am

Buy a genuine Stat - cheap ones are asking for trouble.

Are you sure the viscous is working - the fan will spin all the time the engine is running but the viscous clutch only engages to properly drive air through the rad when the engine is hot. You need to do the "newspaper test" to check if you havent done so already.
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
cee
E30 Zone Regular
E30 Zone Regular
Posts: 983
Joined: Sun Aug 23, 2009 11:00 pm
Location: Plymouth

Post Wed Dec 21, 2011 10:59 am

Ah okay, will give that a try. The engine runs a lot hotter while stationary, which may well suggest a fan issue, didn't think of that!
Image
1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
User avatar
domkolo
E30 Zone Regular
E30 Zone Regular
Posts: 437
Joined: Sat Nov 27, 2010 11:00 pm

Post Fri Dec 23, 2011 10:33 am

if it's running hotter when stationary replace the viscous coupling and it'll stay at the right temp, i had that problem a fewmonths back and it's all fine now,
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Dec 23, 2011 4:58 pm

This all sounds like a leaking throttle body heater gasket to me, especially since work has been done in that area.
The whole thing can be bypassed with no ill effects (in the UK).
cee
E30 Zone Regular
E30 Zone Regular
Posts: 983
Joined: Sun Aug 23, 2009 11:00 pm
Location: Plymouth

Post Wed Jan 04, 2012 2:33 pm

Brianmoooore wrote:This all sounds like a leaking throttle body heater gasket to me, especially since work has been done in that area.
The whole thing can be bypassed with no ill effects (in the UK).
Been away for 2 weeks so will read through this topic again when I get time, however this seems like a logical cause as the gasket was in a bit of a state, however what I don't get is, the TB gasket doesn't hold back any liquid, and only seems to act as a compromise for poor fitment of the heater to the inlet manifold...(from what I can tell)?
Image
1990 Sterlingsilber 318iS - 146 bhp / 192 Nm