Dropping rear subframe - quick Q

Need technical Q/A then you're in the right place

Moderator: martauto

Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Dec 17, 2011 9:45 pm

Attempted this today, and made some progress but got stuck.

Side plates removed and main 22mm bolts undone. ARB and shock bolts undone, and the trailing arms lowered to the floor. Brake flexis cut. Diff bush bolt removed, unbolted from the prop, and diff lowered down but not on the floor yet.

Now, one side dropped immediately before I even had a chance to hammer the bolt up, so that's lowered by about 1". On the other, the alloy centre has welded to the car, so I'm having to hack away at the rubber to make it fall.

Using a crow bar, the subframe will move away from the car by nearly 2", but I just can't seem to get it to drop. Could this be because the prop bolts are still going through to the diff, even though they're not secured? With the trailing arms already on the floor, it seems incredible that the whole lot hasn't dropped yet, and I can't see what's stopping it.
Sanchez
Married to the E30 Zone
Married to the E30 Zone
Posts: 7578
Joined: Sun Apr 17, 2005 11:00 pm
Location: Sunny Scotland

Post Sat Dec 17, 2011 9:48 pm

Brake flexis cut but what about the handbrake?
Image
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Sat Dec 17, 2011 9:50 pm

Remove the whole prop
Done the handbrake cables?

The subframe has to come out evenly from both sides, lift the other side back in and try to make both sides lower at the same time
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Dec 17, 2011 9:54 pm

Gah, the handbrake cables run under the subframe, don't they? Would that be enough to stop it dropping down?

The evenness would also be an issue, so I'll get on that too. I brained myself with the breaker bar today, so I'm not thinking too straight...
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Sat Dec 17, 2011 10:02 pm

You'd almost be better off bolting the trailing arms back to the shocks as if the arse end sags down it does make it difficult for the subframe to drop down "square" if you know what I mean.

Knock the splined bolts back up into the shell so they pop into the rear seat area (you have to take the seat base out). Then get a largish screwdriver from underneath and insert it into the centre of the alloy bush centre and give it a good wiggle, watch out for the subframe falling onto your hand though :)
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Dec 17, 2011 10:14 pm

Bolt's out on side one side, but that's the side that refuses to drop. Gave the ally a hammering with some 8mm bar pushed inside, and all I managed to do was bend the bar...

For starters, I'll get the diff off properly in case the prop is being an issue, then I'll jack it all back up straight and take it from there.
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Sat Dec 17, 2011 10:18 pm

Just undo the prop from the centre bearing mount, stick a trolley jack under the diff and jack it back up a bit and then have another go giving it a wiggle
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Sat Dec 17, 2011 10:38 pm

Jam something in the hole and give it a good wiggle
I did this to mine and it came out
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Dec 17, 2011 10:44 pm

redcar wrote:Jam something in the hole and give it a good wiggle
I did this to mine and it came out
thats wot i did to the wife. (same result) :mad: :mad:
SGP
E30 Zone Regular
E30 Zone Regular
Posts: 502
Joined: Thu Aug 31, 2006 11:00 pm

Post Sun Dec 18, 2011 2:03 am

The centre of the bush is welded into the socket under the car, I ended up using a 5ft long steel bar to lever it apart. Brute force required.
If it ain't broke..
Fix it till it is :)
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Sun Dec 18, 2011 8:53 am

When we dropped the original subframe on my touring the alloy bush centre snapped off in the mounting point :x

Had to drill the fecker out and clean it up - make sure you put a good layer of copper grease on the alloy of the new bush when you refit :wink:
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Fri Jan 06, 2012 3:23 pm

Took off the diff, lifted the trailing arms back up on bricks, and then used a crowbar to pull down the subframe. Slid off neatly!

Now I've got to get these f**king trailing arm bolts undone...