Fast Idle
Moderator: martauto
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
My 1989 325i SE has developed a problem. Since it went for some welding work, it now wants to idle at 1.2k all the time sometimes up to 1.5k. For cold starts it's an improvement on what it was like, but I find it embarrassing sitting at traffic lights sounding like I am preparing to launch! I have checked for 350 ohm at the blue plug and checked pin 45 on the ECU. Both are reading 350 ohm engine warm, removing the power from the Idle stability valve, sometimes drops the revs a little, but as i understand it the opposite should happen!? Other than getting the ECU checked not sure where to go next! Bit of a coincidence that ECU cover was removed when the welding job was done?! Am i being paranoid?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Which ECU does your car have? Number's on a label on the case.
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
Brian,
It's a Motronic Bosch 0 261 200 173. WBAAA12070 AE53756 AO5E.
Not sure what numbers you need so given all.
It's a Motronic Bosch 0 261 200 173. WBAAA12070 AE53756 AO5E.
Not sure what numbers you need so given all.
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
if your needing an ecu i have the one in question.pm if you want it
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
After more driving it seems, she runs 1.5k Cold and 1.2k Warm? Any ideas, will give the Idle stability valve a good clean, but not expecting any change. Can welding work damage any relevant components?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Welding work can damage electronic components if care isn't taken and thought isn't given to where the current to the earth clamp will run through the car. This is why I asked about the ECU number. The 731 that you have is normally ultra reliable, but the later 381 is known to develop idle control problems.
What exactly do you mean by "Bit of a coincidence that ECU cover was removed when the welding job was done?!" in your OP?
What exactly do you mean by "Bit of a coincidence that ECU cover was removed when the welding job was done?!" in your OP?
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
I wasn't entirely convinced that it was necessary for him to remove the cover, as the area he was welding was the bottom of the o/s inner wheel arch, he said he had to take the accelerator pedal out. He found a loose wire and re connected it for me, the wire was the lights on the headlight angle adjuster. Probably me being paranoid, I have had work done on my car before and thought bits had been changed wheels etc... Just seems odd how the idle characteristics have now changed! 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
You mean the under dash panel that closes in the area above the driver's legs? I would remove this panel if welding where you say, in order to be able to lift the carpet clear of the area and turn it back.
To repair this area properly, and in a way that will last for the next twenty years, the carpet really needs to come completely out. (Which will almost certainly reveal a few more areas that need MIG attention.)
To repair this area properly, and in a way that will last for the next twenty years, the carpet really needs to come completely out. (Which will almost certainly reveal a few more areas that need MIG attention.)
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
You're right Brian! Any more checks I can make to resolve the fast idle?
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
A good friend of mine Dave, RIP once told me, on older high mileage cars you have to either adjust the valve clearances tighter or looser than the recommended gap! I can't remember which, and I can't ask him now, so does anyone on here know what he meant?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
On some designs of engine (BL A series comes to mind), one side of the gap that you slide the feeler gauge into becomes worn concave. The feeler gauge bridges over this concave surface, with the result that the clearances end up too great, so the advice was to set the measured clearance slightly tight to compensate.
Off no relevance to a BMW engine of course, although you'll never set the tappets correctly on a M20 if the eccentrics are worn.
Have you checked for something as basic as a dislodged throttle cable, preventing the throttle from closing onto its stop?
Off no relevance to a BMW engine of course, although you'll never set the tappets correctly on a M20 if the eccentrics are worn.
Have you checked for something as basic as a dislodged throttle cable, preventing the throttle from closing onto its stop?
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
Thanks Brian your depth of knowledge is impressive!
I have checked the throttle cable, initially it wasn't seated properly, I thought I had found the problem when I saw that, but turned out not to be the case, the cable is quite free and doesn't prevent the throttle closing, gave the Idle stability valve a good flush yesterday, bit mucky but appears to be working ok. Still got a fast idle cold and warm.
Changed the clips on the power steering hoses! thought that was going to be a quick easy job! Not so easy...couldn't get the larger pipe off then had a brain wave and unscrewed the replacement jubilee clip completely d'oh! wrapped it around the pipe tightened it back up so I didn't have to remove the pipe...which lets face it was never coming off! Also changed the fuel filter as part of the 24k service, to date I have adjusted the valve clearances every 24k. But due to the age and condition of the car not so sure wether its worth doing, likewise HT leads and spark plugs, checked both, spark plugs are in good condition and no flashing or problems detected from leads. the sparks are the bosch four conductor types they seem to wear better.
I have checked the throttle cable, initially it wasn't seated properly, I thought I had found the problem when I saw that, but turned out not to be the case, the cable is quite free and doesn't prevent the throttle closing, gave the Idle stability valve a good flush yesterday, bit mucky but appears to be working ok. Still got a fast idle cold and warm.
Changed the clips on the power steering hoses! thought that was going to be a quick easy job! Not so easy...couldn't get the larger pipe off then had a brain wave and unscrewed the replacement jubilee clip completely d'oh! wrapped it around the pipe tightened it back up so I didn't have to remove the pipe...which lets face it was never coming off! Also changed the fuel filter as part of the 24k service, to date I have adjusted the valve clearances every 24k. But due to the age and condition of the car not so sure wether its worth doing, likewise HT leads and spark plugs, checked both, spark plugs are in good condition and no flashing or problems detected from leads. the sparks are the bosch four conductor types they seem to wear better.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
It almost sounds as if the ECU thinks that the air conditioner is switched on and is increasing the revs to compensate for the drag of the compressor.
Brian has mentioned in a post before how the one pin on the ECU can be held up to +12 volts if you want to increase the idle....maybe you have something like this happening when you do not want it!
I have had a case of the engine idling too high when the air con was switched on but the air con clutch had not engaged due to a broken wire so the drag of the compressor was not there.
just a thought of something worth checking.
Brian has mentioned in a post before how the one pin on the ECU can be held up to +12 volts if you want to increase the idle....maybe you have something like this happening when you do not want it!
I have had a case of the engine idling too high when the air con was switched on but the air con clutch had not engaged due to a broken wire so the drag of the compressor was not there.
just a thought of something worth checking.
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
Thanks Bill, My car doesn't have air con. But it's possible it's getting the wrong information from somewhere?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The 'air con on' signal is fed to the ECU by applying 12 volts to a purple/grey wire in a four pin plug hanging off of the engine loom a couple of inches or so from the ECU plug.
-
loogie1
- E30 Zone Newbie

- Posts: 151
- Joined: Wed Jan 11, 2006 11:00 pm
So not as simple as something shorting out! I think I saw the plug your referring to. Could a bad earth be an issue?
