Alpina C2 engine specification/distinguishing marks/genuine?

Need technical Q/A then you're in the right place

Moderator: martauto

nickphine
E30 Zone Regular
E30 Zone Regular
Posts: 282
Joined: Sun Dec 03, 2006 11:00 pm
Location: Kendal

Post Mon Dec 12, 2011 11:09 pm

Hi chaps

Does anyone have any definitive information about the specs of Alpina C2 engines. I've just bought what appears to be one and I need to find out .

It's got an 81mm crank(good). 135mm rods (very good) and therefore custom pistons (hurrah!). The block is stamped with a 4 digit code and the C2/1 marks and also the engine number 'appears' to have been re-stamped (that might be my inexperience though).

The head appears a standard 885, although it has 2.5 2.7 cast on it, unlike my other 885 head. Porting appears standard (bad?) as do the valves. haven't measured the cam yet. Head is cracked anyway.

Any thoughts would be appreciated although I'd rather get knowledge than guesses, judging by the frankly frightning lack of knowledge I've just witnessed on an 'LSD or not post', scary...

Cheers, Nick Hine
User avatar
Rodderz
E30 Zone Addict
E30 Zone Addict
Posts: 3105
Joined: Thu Nov 24, 2005 11:00 pm
Location: Southampton

Post Mon Dec 12, 2011 11:22 pm

These are the numbers stamped on my C2 2.7 block.

Image
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Mon Dec 12, 2011 11:27 pm

all late heads have 2.5 2.7 cast into it. Theres a raised tab near the front of the head if its genuine then it will have a 4 digit stamp here. But if theres no head work i doubt it as they reworked on all the ports and chambers

The bottom end sounds legit to me, thats the hard part really.
nickphine
E30 Zone Regular
E30 Zone Regular
Posts: 282
Joined: Sun Dec 03, 2006 11:00 pm
Location: Kendal

Post Mon Dec 12, 2011 11:42 pm

Thanks chaps, I did read somewhere that the heads were stamped so was assuming the worst. Fingers crossed it's still got the alpina cam in it though. The block looks the same as mine too which is great. Does anyone know the code numbers on the correct crank btw?

Cheers

Nick Hine
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Tue Dec 13, 2011 2:01 am

the biggest difference appears to be the chamber, i have molded a stock and genuine alpina inlet and exhaust port using silicone and mostly its cleaned up ports with the last bit of the exhaust port gasket matched. There seems to alot better flow numbers on the exhaust side but as hairyscreech found this might be from the hemi style chamber rather than anuthing drastic in the port
E30 325is with M20B31
nickphine
E30 Zone Regular
E30 Zone Regular
Posts: 282
Joined: Sun Dec 03, 2006 11:00 pm
Location: Kendal

Post Tue Dec 13, 2011 9:10 am

That makes sense, even from my limited knowledge of porting, the inlet ports do look 'right' i.e. not obvisouly restrictive at the manifold or valve ends, barring a bit of matching at the gaskets. The exhaust ports do appear to narrow at the gaskets though, quite a large difference between the diameter of the port on exit and the diameter of the gasket and then I'm assuming another step to my btb manifold. From what I know a step between port and exhaust can be a good thing though?

Do you have any photos of the ports and chambers?

Thanks again