timing belt m20
Moderator: martauto
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
hiya can the belt on an e30 be 1 tooth out of timing and still run? i am asking because my engine wont rev past 5500 and it sounds lyk its being choked thts why it wont rev higher.it did before i rebuilt the head and done the timing belt.i have replaced everything i can think of.fuel pump, fuel filter, plugs, leads, distributor, fpr and the ecu yet still no joy.asked a few people and nobody seems to have a clue so this is the last thing i can think of. any help would be appreciated alot as its doing my tits right in now. cheerz Mark
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
forgot to say its not an eta engine
-
craigieeb
- E30 Zone Addict

- Posts: 4988
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: In my man cave modifying... something
Have you made sure the connectors to the T.P.S and the I.C.V are connected up the right way?
(swap them over and see if there is any change)
(swap them over and see if there is any change)
M50 Turbo!!!
I shall say no more 
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
I suppose an M20 may run but crap if one tooth was out, not something i have ever tried,
surely it makes sense to first of all have a look and see if the timing marks are lined up properly ? if it is even one tooth out on the belt they won't line up
surely it makes sense to first of all have a look and see if the timing marks are lined up properly ? if it is even one tooth out on the belt they won't line up
-
maxfield
- Old Skooler

- Posts: 15185
- Joined: Sat Nov 26, 2005 11:00 pm
- Location: Mansfield
With my experience in do cambelts, you can never get the cambelt spot on. But thats my experience though. I would always put the tooth out the the tensioner side as the belt stretches it becomes right again. IMO can't see it stopping revving.

-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
it runs perfect up until i hit 5500
-
chh137
- E30 Zone Squatter

- Posts: 1502
- Joined: Mon Apr 18, 2011 11:00 pm
- Location: deepest darkest derbyshire
rev limiter/
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
it should limit at 6200 plus its got a chip so it should rev to 7000.is there a way of adjusting the rev limiter or is that only possible on the m10 carb engine?
-
kewliost
- E30 Zone Newbie

- Posts: 16
- Joined: Sun Jan 02, 2011 11:00 pm
We need more info about your car? i take it is motronic if you put a chip in, what kind of chip did you put in?
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
the engine is from a 325ise motoronic. its a speedtouch chip and it limited at 5500 before i fitted the chip to it aswell. the ecu has 173 at the end of the part number. when i first start the car and let it idle the first rev i give it it will rev to 7000 then after that 5500 but it sounds like the engines being strangled and stopping it from reving higher it doesnt sound like a normal car on the limiter.it says above the things i have checked and i dont know what else it could be other than the things i have listed.any help will be greatly appreciated because its starting to wind me right up now
cheerz
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
afm? maybe the flap is getting stuck and wont open all the way.. just a thought 
-
markgE30
- E30 Zone Newbie

- Posts: 134
- Joined: Wed Feb 02, 2011 11:00 pm
- Location: falkirk scotland
cleaned that out with wd40 aswell still no change
