Head drilled? any ideas

Need technical Q/A then you're in the right place

Moderator: martauto

TouringTash
E30 Zone Team Member
E30 Zone Team Member
Posts: 3803
Joined: Mon Jun 28, 2010 11:00 pm
Location: Kent

Post Thu Dec 08, 2011 11:15 pm

Came off a working lump, thoughts please.

Image
318i Touring
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Fri Dec 09, 2011 7:05 am

They all have it.

Heres a shot of one of mine:

Image
By b7tmw at 2011-12-08
B7's Motto. "If it's French, BURN IT!!!!!!"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Dec 09, 2011 8:40 am

It's part of the oil feed arrangements to the top end, IIRC.
TouringTash
E30 Zone Team Member
E30 Zone Team Member
Posts: 3803
Joined: Mon Jun 28, 2010 11:00 pm
Location: Kent

Post Fri Dec 09, 2011 3:26 pm

Cheers Trevor & Brian, now that I'm looking at it with open eyes and not OMG what's gone on here I can see the extra bit of 'meat' @ 4 O'clock from the drilled point on your lovely, clean and shiny head.
Time for a strip, clean and send it off for some work then. :thumb:

Thankfully I can't help Hairy with getting to the bottom of why heads crack on 6 pots
http://www.e30zone.net/modules.php?name ... c&t=210764 something you two would know tons more than me about. I would blame a lack of mechanical sympathy for each and every failure and a failed viscous.
318i Touring
User avatar
fowler
Boost Junkie
Posts: 3468
Joined: Mon Jan 10, 2005 11:00 pm
Location: New Addington/Croydon

Post Fri Dec 09, 2011 8:26 pm

Heat coefficient between to disimilar metals. :D me thinks
EX A-Tech Workshop bitch !!!
325i Turbo touring (Aka Project Fridge)
gone but not forgotten
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Fri Dec 09, 2011 11:05 pm

im currently wondering if there is something that promotes a hot spot on one side of the head resulting in a hot sides and cold center, thus putting stress into the material in the center.
but that's a discussion for after i have spoken to the unis materials and structures specialist.

as far as that head goes everyone i have seen so far of all types has had that drilling, not sure why they chose to feed the oil like that but not had a good look at it.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
TouringTash
E30 Zone Team Member
E30 Zone Team Member
Posts: 3803
Joined: Mon Jun 28, 2010 11:00 pm
Location: Kent

Post Sat Dec 10, 2011 12:13 am

fowler wrote:Heat coefficient between to disimilar metals. :D me thinks
:wave:
318i Touring
User avatar
fowler
Boost Junkie
Posts: 3468
Joined: Mon Jan 10, 2005 11:00 pm
Location: New Addington/Croydon

Post Sat Dec 10, 2011 2:35 am

winkeye
how does
EX A-Tech Workshop bitch !!!
325i Turbo touring (Aka Project Fridge)
gone but not forgotten
TouringTash
E30 Zone Team Member
E30 Zone Team Member
Posts: 3803
Joined: Mon Jun 28, 2010 11:00 pm
Location: Kent

Post Sat Dec 10, 2011 2:37 am

working late?


Or hiding from the Mrs?
318i Touring
User avatar
fowler
Boost Junkie
Posts: 3468
Joined: Mon Jan 10, 2005 11:00 pm
Location: New Addington/Croydon

Post Sat Dec 10, 2011 2:41 am

Nights mate only 4hr45mins to go :D
EX A-Tech Workshop bitch !!!
325i Turbo touring (Aka Project Fridge)
gone but not forgotten
TouringTash
E30 Zone Team Member
E30 Zone Team Member
Posts: 3803
Joined: Mon Jun 28, 2010 11:00 pm
Location: Kent

Post Sat Dec 10, 2011 2:42 am

lol Glad it's going well.

Had any karzis to sort?
318i Touring
User avatar
fowler
Boost Junkie
Posts: 3468
Joined: Mon Jan 10, 2005 11:00 pm
Location: New Addington/Croydon

Post Sat Dec 10, 2011 2:44 am

na not yet mate..
EX A-Tech Workshop bitch !!!
325i Turbo touring (Aka Project Fridge)
gone but not forgotten
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Sat Dec 10, 2011 2:45 pm

HairyScreech wrote:im currently wondering if there is something that promotes a hot spot on one side of the head resulting in a hot sides and cold center, thus putting stress into the material in the center.
but that's a discussion for after i have spoken to the unis materials and structures specialist.

as far as that head goes everyone i have seen so far of all types has had that drilling, not sure why they chose to feed the oil like that but not had a good look at it.
I think it's to "stall" or delay the drain back to the sump. If it direct feed and not off set, the return would be to quick. It may also have to do with crank case pressure.

Although they have been know to crack all along under the cam, more often than not, it's at the rear above 6 5 & 4 they go. The reason? M20's run hotter to the rear than the front. And as Si says, 2.7's run even hotter. I can physicaly feel that my 2.7 runs hotter than my old 2.5 when I open the bonnet.
B7's Motto. "If it's French, BURN IT!!!!!!"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Dec 10, 2011 8:16 pm

HairyScreech wrote:im currently wondering if there is something that promotes a hot spot on one side of the head .
Well, there's six exhaust ports on one side carrying gas at a few hundred degrees, and six inlet ports on the other, flowing air at the ambient, and being refrigerated by vaporising fuel.
e301988325i
E30 Zone Addict
E30 Zone Addict
Posts: 3701
Joined: Fri Feb 01, 2008 11:00 pm
Location: Taunton, Somerset

Post Sat Dec 10, 2011 8:23 pm

Sorry for the hijack, but has anybody suffered a crack head with a tubular manifold fitted? I'm thinking a tubular manifold will hold a lot less heat then the cst logs when the engine is switched off.
I said:

Can anyone suggest how to test if the boot lights are staying on with the boot shut?

e30topless said:

lock the wife in there