2 issues
Moderator: martauto
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
not long ago i had built a m20b28 stroker using new main and big end bearings, rings, 290 cam, all the gaskets inc seals, to make the list short everything else in the head. including all water hoses.
i had the head professionally pressure tested which came back ok also skimmed. Put it all back to gather using a 79 degrees celsius thermostat instead of the 80 degrees celsius.
the first issue is that every 4 weeks i need to top up with water as the coolant light comes on, iv checked for water leaks but can see any, car drives 100% with no overheating issues also in the cold within 5min of cold start the steam stops. has anyone got any ideas?
the second is, iv noticed a small oil leak coming somewhere from the front top of the engine. dont no where its coming from, all the gaskets were replaced including the cam,crank seal and all the other seals. the bottom of the block is dry apart from the oil that was travelled from the top to the bottom. i at first thought that it might be coming from the head, its only wet at one (exhaust side near the cam pully) side and not the hole head. can someone help on this?
Both of these issues are very frustrating so can some please help.
i had the head professionally pressure tested which came back ok also skimmed. Put it all back to gather using a 79 degrees celsius thermostat instead of the 80 degrees celsius.
the first issue is that every 4 weeks i need to top up with water as the coolant light comes on, iv checked for water leaks but can see any, car drives 100% with no overheating issues also in the cold within 5min of cold start the steam stops. has anyone got any ideas?
the second is, iv noticed a small oil leak coming somewhere from the front top of the engine. dont no where its coming from, all the gaskets were replaced including the cam,crank seal and all the other seals. the bottom of the block is dry apart from the oil that was travelled from the top to the bottom. i at first thought that it might be coming from the head, its only wet at one (exhaust side near the cam pully) side and not the hole head. can someone help on this?
Both of these issues are very frustrating so can some please help.
-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
I bet the oil leak is coming from the front of the head where the oil gallery from the block meets the head?
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
what makes you say that? and how could i sort it.sweep wrote:I bet the oil leak is coming from the front of the head where the oil gallery from the block meets the head?
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
oil leaking from rocker cover gasket? that is a common place on M20s
E30 Crazy!
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
rocker cover gasket was replaced, the sides of the head under the rocker cover seems to be dry, but will double check tomorrowAjsingh wrote:oil leaking from rocker cover gasket? that is a common place on M20s
-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
It seems to be a weak point as theres a high pressure from the oil gallery
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
bit of a dumb question, but what do you mean by oil gallery
1989 cab M20B28 build
http://www.e30zone.net/modules.php?name ... highlight=
http://www.e30zone.net/modules.php?name ... highlight=
-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
My money's on this.Ajsingh wrote:oil leaking from rocker cover gasket? that is a common place on M20s

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
This! The oil feed to the head from the block is via the second from the front head bolt hole on the exhaust side. Leaks out of the side of the join are very common, especially if a non genuine head gasket is used.sweep wrote:I bet the oil leak is coming from the front of the head where the oil gallery from the block meets the head?
Minor water leaks can be an absolute pain to trace.
Very occasional leaks from the water pump are a common one, or the tiniest leak in the rad, which evaporates instantly.
Checked under the carpet in the cabin? Does the windscreen mist up more before it begins to clear when you use the demister?
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
why would it leak if a non genuine head gasket was used, where is the best place to get a genuine one from apart from the dealers.Brianmoooore wrote:This! The oil feed to the head from the block is via the second from the front head bolt hole on the exhaust side. Leaks out of the side of the join are very common, especially if a non genuine head gasket is used.sweep wrote:I bet the oil leak is coming from the front of the head where the oil gallery from the block meets the head?
Minor water leaks can be an absolute pain to trace.
Very occasional leaks from the water pump are a common one, or the tiniest leak in the rad, which evaporates instantly.
Checked under the carpet in the cabin? Does the windscreen mist up more before it begins to clear when you use the demister?
water pump is new but will check near the pump when i can as busy at work, the carpet is dry, and sometimes the windscreen does mist up before it begins to clear when using the demister also makes a grinding sound from the heater blower.
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
bump
1989 cab M20B28 build
http://www.e30zone.net/modules.php?name ... highlight=
http://www.e30zone.net/modules.php?name ... highlight=
-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
I dont no why they do this, i have used good aftermarket gaskets before and had no leaks.but i suppose the castings are old now.
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
had a good look over the weekend but couldn't see any water leaks. When using the demister the windscreen demists as normal, also the carpet in the cabin is dry. Any other ideasaceifty wrote:why would it leak if a non genuine head gasket was used, where is the best place to get a genuine one from apart from the dealers.Brianmoooore wrote:This! The oil feed to the head from the block is via the second from the front head bolt hole on the exhaust side. Leaks out of the side of the join are very common, especially if a non genuine head gasket is used.sweep wrote:I bet the oil leak is coming from the front of the head where the oil gallery from the block meets the head?
Minor water leaks can be an absolute pain to trace.
Very occasional leaks from the water pump are a common one, or the tiniest leak in the rad, which evaporates instantly.
Checked under the carpet in the cabin? Does the windscreen mist up more before it begins to clear when you use the demister?
water pump is new but will check near the pump when i can as busy at work, the carpet is dry, and sometimes the windscreen does mist up before it begins to clear when using the demister also makes a grinding sound from the heater blower.
-
fixedwheelnut
- E30 Zone Regular

- Posts: 909
- Joined: Sun Nov 20, 2005 11:00 pm
- Location: South East London
I recently had a slow leak with no visible signs, I pressure tested it over three hours and eventually at max pressure found a small leak at the top of the radiator.
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
Forgot to say, the car has never used water before until i had a broken rocker arm replaced it and had the head skimmed and pressure tasted and put back together, after this work the car has been using water.
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
bump
1989 cab M20B28 build
http://www.e30zone.net/modules.php?name ... highlight=
http://www.e30zone.net/modules.php?name ... highlight=
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Pressure test it, as per fixedwheelnut.
If the pressure test appears to consume coolant, but you still can't find the leak, remove the spark plugs before cranking the engine, in case you have a cylinder partly filled with coolant.
If the coolant is ejected from one cylinder when you do turn it over, you've a) located the leak, and b) avoided bending a conrod.
If the pressure test appears to consume coolant, but you still can't find the leak, remove the spark plugs before cranking the engine, in case you have a cylinder partly filled with coolant.
If the coolant is ejected from one cylinder when you do turn it over, you've a) located the leak, and b) avoided bending a conrod.
-
SGP
- E30 Zone Regular

- Posts: 502
- Joined: Thu Aug 31, 2006 11:00 pm
If the heads been off, there is a fair chance this is the problem. My m20 mysteriously consumes coolant (mostly on start up when the engines cold, and with a misfire or lumpy idle) less than 10k since head skimmed etc.. I'm sure Brian hit the proverbial nail re. the oil leak.. Word.
If it ain't broke..
Fix it till it is
Fix it till it is
-
hongkongfuey
- Mad-tango-geezer
- Posts: 3303
- Joined: Fri Jun 08, 2007 11:00 pm
- Location: portsmouth
For the oil leak, when i was at bmw, there was a mod on the piece of metal that locates the rocker shafts, it presses on the underside of the rocker cover at the front, with thinner baskets it holds the rocker cover off slightly, the way to sort it is take out the shaft locator, and file off 1mm off the top where it would meet the rocker cover, hold it against the cover to see where to file off, put back and if should my leak again
if there wern't people like me,
with cars like mine,
who would you put down to make yourself feel better?
with cars like mine,
who would you put down to make yourself feel better?
-
aceifty
- E30 Zone Regular

- Posts: 866
- Joined: Mon Jan 26, 2009 11:00 pm
- Location: never you mind
how would I carry out that pressure test?Brianmoooore wrote:Pressure test it, as per fixedwheelnut.
-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
Get it done from a specialist Ifty.aceifty wrote:how would I carry out that pressure test?Brianmoooore wrote:Pressure test it, as per fixedwheelnut.

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
SGP
- E30 Zone Regular

- Posts: 502
- Joined: Thu Aug 31, 2006 11:00 pm
Some garages have a device to check for combustion deposits in the coolant. Just a suggestion.
If it ain't broke..
Fix it till it is
Fix it till it is
