Prop shaft vibrations?

Need technical Q/A then you're in the right place

Moderator: martauto

k17byo
E30 Zone Newbie
E30 Zone Newbie
Posts: 86
Joined: Sun Sep 06, 2009 11:00 pm

Post Sun Dec 04, 2011 4:59 pm

Hi everyone ;)

I had a funny knocking under my 325i sport a few months ago under heavy acceleration, so I had a mate replace centre bearling and doughnut!

Since he replaced those it vibrates over 60! More of a shudder!

I asked him if he marked the prop up before splitting it but he said it only goes one way and that it's not multi splined?

Is this true?

Any advice?
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Sun Dec 04, 2011 5:02 pm

Tech thread shirley?
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 04, 2011 5:12 pm

iirc it has to be pre tensioned as well when fitting the centre bearing. im sure the two halfs of the prop can be mixed around if not marked.
kev76
E30 Zone Newbie
E30 Zone Newbie
Posts: 172
Joined: Mon Aug 16, 2010 11:00 pm
Location: stoke...staffs

Post Sun Dec 04, 2011 5:13 pm

needed marking . they are multi splined :eek:
Image
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Sun Dec 04, 2011 5:20 pm

props I've seen have two white blobs which line up from the factory, so if he hasn't marked it may be worth looking for them. As fuzzy says, the centre bearing needs a preload.. details will more than likely be in the zone wiki..
k17byo
E30 Zone Newbie
E30 Zone Newbie
Posts: 86
Joined: Sun Sep 06, 2009 11:00 pm

Post Sun Dec 04, 2011 6:05 pm

I'm pretty sure the bearing I bought was already in the housing! I bought it all in one to save time and effort ;)
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 6:27 pm

props need to be marked when taken off otherwise when you put them back they are out of balance.they only need to be one spline out and the create the noise you speak about mate
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 04, 2011 6:34 pm

k17byo wrote:I'm pretty sure the bearing I bought was already in the housing! I bought it all in one to save time and effort ;)
its a one piece item but it need to be preloaded on fitting.
k17byo
E30 Zone Newbie
E30 Zone Newbie
Posts: 86
Joined: Sun Sep 06, 2009 11:00 pm

Post Sun Dec 04, 2011 6:53 pm

I knew it! Well I won't be using him again!
Do u know if the bearing is reuse able after bein used and under the assumption this muppet didn't preload it?
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 6:55 pm

it.s a two piece item that needs splitting to replace the centre bearing so it needs marking before you split it but as you say needs pre loading when you refit it
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 04, 2011 6:58 pm

threelander wrote:it.s a two piece item that needs splitting to replace the centre bearing so it needs marking before you split it but as you say needs pre loading when you refit it
the prop is a two piece item that needs splitting, the centre bearing is a one piece item than needs pre loading upon fitting iirc, its been a while since i did mine but i used to do them often... is the centre bearing the correct way around? iirc its slightly off centre on the carrier and will go either way as well. you should be able to reuse it.
k17byo
E30 Zone Newbie
E30 Zone Newbie
Posts: 86
Joined: Sun Sep 06, 2009 11:00 pm

Post Sun Dec 04, 2011 7:31 pm

That was another question I asked him but he assured me it only went one way!
Is there anyone in the brighton area that might be able to sort this for me? Someone that might have half a clue what their doin lol
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 04, 2011 7:38 pm

my prop was custom made but i used the standard bearing and carrier, thats why im a little unsure .
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 10:09 pm

do it yourself m8 not a hard job tye bearing goes on one way and one way only for anyone with an ounce of common sense. read the wiki files in here mate but its more like your man has not marked the prop when he split it and it is not balanced.easy sorted if you get someone what knows a e30 mate
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 10:13 pm

hi fuzzy i,m baffled if you got a one piece prop how and why do you need a centre bearing and how do you replace it
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 04, 2011 10:21 pm

no, the prop is a 2 piece and the centre bearing is 1 piece, with the bearing already mounted within the carrier when you buy it.
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 10:28 pm

yes
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Sun Dec 04, 2011 10:41 pm

sorry fuzzy :o:
mrLEE30
E30 Zone Team Member
E30 Zone Team Member
Posts: 6589
Joined: Tue Jan 18, 2005 11:00 pm
Location: Sweating buckets in Bahrain

Post Mon Dec 05, 2011 4:50 am

The prop is multi splined but given the position of the two u joints there is really only a few obvious correct alignments, I.e so the u joints are in the same plane.

First pre load the centre bearing, (assuming you have not ripped the rubber mount), you will see the mounting holes are slotted, start with the bearing in its natural position, and hand tighten the two mounting bolts, then slide the bearing 5mm toward the gearbox and tighten in this position. If this does not cure vibration then your prop is misaligned or the donut is perished.

Also moved to tech section, Shirley.
Image
k17byo
E30 Zone Newbie
E30 Zone Newbie
Posts: 86
Joined: Sun Sep 06, 2009 11:00 pm

Post Mon Dec 05, 2011 7:21 am

Thanks for all the advice!
I have got half a clue as I did restore the whole car myself!
This was the first person I'd ever let loose on my car and he makes a right mess of it :-/
Looks like I'll just have to find time to do it myself