Removing bumper bump strips
Moderator: martauto
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
Are they clipped or bolted? Is it just a case of pulling them or is there a hidden bolt somewhere I can't find?
Last edited by cee on Wed Nov 23, 2011 8:39 pm, edited 1 time in total.

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
DHFiS
- Old Skooler

- Posts: 2733
- Joined: Sat Aug 12, 2006 11:00 pm
- Location: cambridge
Are we talking about the black strips on the doors? If so they are clipped on. Best way I found to remove them was from the rear but be prepared to break some of the plastic clips.
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
No sorry, typo in the title. The bump strips on the bumpers.DHFiS wrote:Are we talking about the black strips on the doors? If so they are clipped on. Best way I found to remove them was from the rear but be prepared to break some of the plastic clips.

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
There is a small plastic nut on the outer edge of the strip on the door, if you open it, you'll see it where the strip starts,
The rest ar clipped into plce on the rear arch, and the front arch has a nut on the inside of the wing.
The rest ar clipped into plce on the rear arch, and the front arch has a nut on the inside of the wing.

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Front bumper trims just clip off.
Rear bumper has to be removed to get the corner pieces off,little star headed bolt from memory?
Rear bumper has to be removed to get the corner pieces off,little star headed bolt from memory?

-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
Must type faster. 

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
DHFiS
- Old Skooler

- Posts: 2733
- Joined: Sat Aug 12, 2006 11:00 pm
- Location: cambridge
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
Great, see now. Thanks!

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
If you want to take them off intact, remove the bumper, bring it indoors, crank the heating right up, then carefully release the clips from the inside with a flat blade screwdriver.
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
Yes, part 11 in the RealOEM link given above is a star headed nut. Suitable tool for this? It's far too big for anything I have...

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
TouringTash
- E30 Zone Team Member

- Posts: 3803
- Joined: Mon Jun 28, 2010 11:00 pm
- Location: Kent
A trip to halfords for the correct tool and a can of a wd40 type of product that smells of lemon to drown them in first. These are a pig to release from past experience. Has only been 8 bumpers in total and only 3 bolts have come out without blood and tears.
This MAY be what is needed http://www.halfords.com/webapp/wcs/stor ... 65469#dtab
but it's late, my eyes are hanging out and I doubt I'll make the stairs this morn so don't spend any cash till a more awake zoner confirms you need the 55.
This MAY be what is needed http://www.halfords.com/webapp/wcs/stor ... 65469#dtab
but it's late, my eyes are hanging out and I doubt I'll make the stairs this morn so don't spend any cash till a more awake zoner confirms you need the 55.
318i Touring
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
Thanks!

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
its a Torx drive T-55 size.

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Check that it is torx first. Early facelift cars used 10mm hex.
-
cee
- E30 Zone Regular

- Posts: 983
- Joined: Sun Aug 23, 2009 11:00 pm
- Location: Plymouth
Definitely torx. Thanks guys!

1990 Sterlingsilber 318iS - 146 bhp / 192 Nm
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
I believe you meant to say "It's" as in 'it is'.mrLEE30 wrote:its a Torx drive T-55 size.
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
TouchéAndyboy wrote:I believe you meant to say "It's" as in 'it is'.mrLEE30 wrote:its a Torx drive T-55 size.

-
TouringTash
- E30 Zone Team Member

- Posts: 3803
- Joined: Mon Jun 28, 2010 11:00 pm
- Location: Kent
Poor bloke was doing his best, surrounded by heathens, sand and a lack of the English way of life let alone rolling hills, dales and vales. Surely a little leniency can be afforded towards one afflicted no doubt each day by poor grammar. 
318i Touring
