Just put the old girl back together - few issues

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Nov 27, 2011 5:21 pm

Today I have fired her up for the first time in a while.

I have just replaced:
ATF filter + oil,
Engine oil + filter
Plugs
Dizzy
Rotor
Water pump
thermostat
Timing Belt
Aux belt
PAS belt
Pas fluid
Inlet manifold gaskets
Had my injectors serviced and cleaned by injectortune


First of all, only the temp gauge on my clocks are working - none of the other gauges. I have the big multiplug thing plugged in but nothing else - but I assume it should work with the multiplug plugged in?

Second of all, The engine oil light on the check panel will not go out

Third of all,
The cooling fan will not go off.
On bleeding the system I got hot air coming out of the blowers fine, The bottom rad hose was getting hot but the water in the reservoir was still cold (I guess this is because I didnt leave it on long enough)

Fourthly,
On changing the ATF and refilling, loads more than 3.0l came out (which is what bentley manual states) and I put a full tub back in (4.55l) and its still not quite up to the minimum on the ATF dipstick - normal?

Fifth,
The injectors now sound very loud - I'm postive they were not that loud before.



Help please!
'88 325i Auto Chromie Cabriolet in Alpine White
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Sun Nov 27, 2011 5:41 pm

James90 wrote:Pas fluid
First of all, only the temp gauge on my clocks are working - none of the other gauges. I have the big multiplug thing plugged in but nothing else - but I assume it should work with the multiplug plugged in?
Have you checked all the fuses etc? In the past half of my dials worked and the other didnt, down to a fuse.

Second of all, The engine oil light on the check panel will not go out
Check the sensor on the block for dirt and grime? Clean it up and plug back in.
Fifth,
The injectors now sound very loud - I'm postive they were not that loud before.

Are you certain its the Injectors and not the rockers now making the noise? Did you do the valve timing?
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Sun Nov 27, 2011 5:43 pm

Also, those Ebay bits! You spanner! Lol,

I got a another set of hoses but 2 of them we're missing from the full set, exactly the same as the other though, and the fuel lines are genuine BMW ones in good order too. PM if you still needed them etc. :thumb:
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Nov 27, 2011 6:13 pm

Fuses in the fuse box in LHS of engine bay? Not since firing it up no but they were all fine before


Check the sensor on the block for dirt and grime? Clean it up and plug back in.

That the one near the engine mount inlet side? Will have a go, never had a problem before today though.


Pretty sure its the injectors, I have put a 1/2" drive extension on the rocker cover and used it as a stethoscope and the tapping in there is different and not as loud.

This set of coolant hoses in really good nick too?
Can you send me a pic of the fuel lines/hoses please?

cheers
'88 325i Auto Chromie Cabriolet in Alpine White
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Sun Nov 27, 2011 7:37 pm

I'll message the pictures over to you bud tomorrow :thumb: