Swapping full loom from one shell to another?
Moderator: martauto
-
DmcL
- E30 Zone Regular

- Posts: 424
- Joined: Thu Mar 12, 2009 11:00 pm
- Location: N.Ireland
anyone done this before and if so how tricky is it? have someone wanting me to swap a loom into another shell and dont really know if i want to take it on or not.
WMMotorsports
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
It's all one piece, and involves stripping out the entire interior (seats, carpets and dash) to get access to it all. Once all the plugs are out and it's unclipped, it then has to be fed through a fist-sized hole in the bulkhead (behind the glovebox) to get to the fusebox.
Then the new loom will have to go back through that hole, snaked around everywhere, clipped in place and then the interior rebuilt.
It's more than a day's work, and although the only "hard" part is getting it through that hole, it's not exactly a fun job.
Then the new loom will have to go back through that hole, snaked around everywhere, clipped in place and then the interior rebuilt.
It's more than a day's work, and although the only "hard" part is getting it through that hole, it's not exactly a fun job.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
DmcL
- E30 Zone Regular

- Posts: 424
- Joined: Thu Mar 12, 2009 11:00 pm
- Location: N.Ireland
as far as i know the car with the loom to come out has everything removed from the interior and the shell its to go into is bare.
not really sure what to charge for a job like that either.. wouldnt want to under charge but also wouldnt want to over charge but id probably need to give some rough idea before i started it rather than do it and then say a price afterwards and it be more then they want to pay, etc.
not really sure what to charge for a job like that either.. wouldnt want to under charge but also wouldnt want to over charge but id probably need to give some rough idea before i started it rather than do it and then say a price afterwards and it be more then they want to pay, etc.
WMMotorsports
-
rossmc88
- E30 Zone Regular

- Posts: 813
- Joined: Wed Nov 21, 2007 11:00 pm
- Location: Fife Scotland
just have an hourly rate, however long it takes x hourly rate = price
Unless its for family, good friend etc
Unless its for family, good friend etc
-
DmcL
- E30 Zone Regular

- Posts: 424
- Joined: Thu Mar 12, 2009 11:00 pm
- Location: N.Ireland
was thinking hourly.. im all good when it comes to doing the work but i have a hard time coming up with a price thats fair. have undercharged on a few occasions before..
maybe £10 an hour? or do we think thats too low/high?
maybe £10 an hour? or do we think thats too low/high?
WMMotorsports
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
If the interior's out, the only time-consuming thing will be writing out all the sticky labels so that you know what each of the plugs is.
Price depends on the client. If was some moneybags hero asking you to build him a track car for his weekends away from the office, I'd ask 150. If it was a mate who just needed a favour, I'd only charge 50 but have him on hand for cups of tea.
Depends whether it's this sort of work that pays your bills too.
Price depends on the client. If was some moneybags hero asking you to build him a track car for his weekends away from the office, I'd ask 150. If it was a mate who just needed a favour, I'd only charge 50 but have him on hand for cups of tea.
Depends whether it's this sort of work that pays your bills too.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
£10 an hour seems fair, but it depends on how long it takes you. If its a bare shell going into bareshell, it shouldnt take you long at all. Like Grrrmachine said, £150 wouldnt be a bad price and I doubt it would take you 15 hours. Unless your stripping it all down in both cars yourself, if so, it might even take longer when putting it all back together.
Then you have to make sure you dont snap or break anything while doing it too.
To actually get the full loom out with everything out the way, it shouldnt take more than an hour, getting it back in, I'm not sure as havent attempting it before, but I'm guessing its not gonna be a fun job.
Everything labelled would make it alot easier.
Then you have to make sure you dont snap or break anything while doing it too.
To actually get the full loom out with everything out the way, it shouldnt take more than an hour, getting it back in, I'm not sure as havent attempting it before, but I'm guessing its not gonna be a fun job.
Everything labelled would make it alot easier.
-
DmcL
- E30 Zone Regular

- Posts: 424
- Joined: Thu Mar 12, 2009 11:00 pm
- Location: N.Ireland
he says everything is labelled already so im thinking id only have to remove the loom from one shell and fit to the other.
this sort of work doesnt pay the bills yet as im still working full time but i would eventually like to either have my own shop/dyno or get in with someone likeminded who already has a business premesis.
the guy isnt a mate but i have done a few wee jobs for him or one of his friends before as well as a chip for an E30 one of them owns.. oddly i think its the loom from the one i chipped thats coming out, must have found some bad rust on the shell or something.
i told him id have to get a look at it first before anything so ill see what it looks like and give him a price after that and see if he wants to pay or try it himself/with his mates.
this sort of work doesnt pay the bills yet as im still working full time but i would eventually like to either have my own shop/dyno or get in with someone likeminded who already has a business premesis.
the guy isnt a mate but i have done a few wee jobs for him or one of his friends before as well as a chip for an E30 one of them owns.. oddly i think its the loom from the one i chipped thats coming out, must have found some bad rust on the shell or something.
i told him id have to get a look at it first before anything so ill see what it looks like and give him a price after that and see if he wants to pay or try it himself/with his mates.
WMMotorsports

