changing gearboxes

Need technical Q/A then you're in the right place

Moderator: martauto

ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Mon Nov 21, 2011 10:15 am

whats the easiest way to change a box on a m20 ?
still in the car if you can get it high enough or really take the whole lump out ? but really dont want to take it out as theres alot more plumbing in mine than a standard m20
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon Nov 21, 2011 11:50 am

If you have access to a car lift and a willing helper fueled with plenty of beer,working from under the car makes much sense.

However,if like I,you only have axle stands and drive on DIY ramps available,then pulling the engine/box out as a unit starts to look appealing.Snag to this is that you have to drain the coolant,advantage is that you have the heavy bits supported on an engine crane and lining the 'box up is a doddle with the engine on the garage floor.
Youth is wasted on the young.
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Mon Nov 21, 2011 12:07 pm

yeah would be a whole lot easier to pull it but I have a lot more plumbing on mine as it's a turbo an it hasn't got a standard loom so it abit more involved than standard to pull it
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon Nov 21, 2011 12:28 pm

Then you are left with only the option of struggling from under the car...

I've only struggled with a starter motor,would not want to take on a 'box in situ!

Wish you luck... :D
Youth is wasted on the young.
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Mon Nov 21, 2011 12:44 pm

ha thanks although i do have a engine crane so i can at least support the engine from above having said that i have done a few th 350 gearboxs from underneth which is a small block chevy auto box so i cant see this being much harder as them auto boxs are bloody heavy lol
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
rix313
E30 Zone Team Member
E30 Zone Team Member
Posts: 4970
Joined: Fri Oct 31, 2008 11:00 pm
Location: Silverstone

Post Mon Nov 21, 2011 2:31 pm

I did my gearbos with the car on axel stands and it was a complete cock and took ages. The second time I used my neighbours ramp and transmission jack and it took about 30 minutes to remove one and refit the other one.
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Mon Nov 21, 2011 2:39 pm

lol ha i know the saying is right if you aint got the right tools to do a job it can be a right bitch
the only reason why i wanna change it is because ive knocked the layshaft bearing out and its got an oil leak so i thought i might aswell kill 2 birds with one stone so to speak
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30